Spec Tech Industrial
Back to Ametek

Buy Your Industrial Control Products Here!

Ametek - Gemco Product and Parts


Ametek Description of Parts


Part No Description
949029L12 Ametek Gemco Cable Assembly for a 953D LDT with a 6 Pin Straight 12mm Euro Connector . Shielded Cable by 12 Feet Long
NEMA 12 Enclosure Ametek Gemco NEMA 12 Enclosure for AHM Panels
004560058 Ametek Gemco Screw on a 1025D Foot & Palm Switch Item 5 1/8
01-533114LXX Ametek Gemco Cable. Resolver Cable 22 AWG., 3 Twisted Pair with Shield. Priced per Foot
014570001 Ametek Gemco Bearing 3/4 (Inch Bore with Flanges
01533002L100 Ametek Gemco Cable. 100 Foot Bulk Resolver Cable for single Turn Resolvers, 22 AWG., 4 twisted Pairs with shield Price per foot / $ 2.00 Add length required at the end of the part number for other lengths (15LB)
01533002L2000 Ametek Gemco Cable. 2000 Foot Bulk Resolver Cable for single Turn Resolvers, 22 AWG., 4 twisted Pairs with shield Price per foot / $ 2.00 Add length required at the end of the part number for other lengths (15LB)
01533002L300 Ametek Gemco Cable. 300 Foot Bulk Resolver Cable for single Turn Resolvers, 22 AWG., 4 twisted Pairs with shield Price per foot / $ 2.00 Add length required at the end of the part number for other lengths
01533002LXX Ametek Gemco Cable. Bulk Resolver Cable for single Turn Resolvers, 22 AWG., 4 twisted Pairs with shield Price per foot. Add length required at the end of the part number XXX (<5LB)
01591317 Ametek Gemco Fluid. Shell Transformer Oil. Standard Fluid for ET Brake Thrusters. Diala AX Transformer Fluid. Sold per LB. About 6 pounds per thruster
01591318 Ametek Gemco Fluid. Silicone Fluid. Optional Fluid for ET Brake Thrusters. Wacker SWS-101-50. Sold per LB. About 6 pounds per thruster
01591448 Ametek Gemco Cord. Teflon Cord, 1/8th Inch Diameter by 90 Foot
04-570252 Ametek Gemco Rod End. Plastic Rod Ends
04-570256 Ametek Gemco Rod End. Female 1/4 -28 UNC Thread Front Rod End. Attaches to the rod / pistion. For use with 955D & DQ, 955LC, 956A, S, LC & DQ LDT'S
04234100 Ametek Gemco Relay, Double Pole, Double Throw, 240 Volt, 60 Hz, 25 Amp (1LB)
04234700 Ametek Gemco Relay, Double Pole, Single Throw, 240 Volt
04513135 Ametek Gemco EPROM. IC EPROM for a 1995-L Micro-Set Programmable Limit Switch. Programmed with ''- X '' Standard Software 128K (<1LB)
04514195 Ametek Gemco Rectifier a component on rectifier E010326
04515173 Ametek Gemco Varistor on rectifier E010326
04517039 Ametek Gemco Intrinsically Safe Barrier. Consult Factory
04517214 Ametek Gemco Panel Mount Bracket for Barrier. Consult Factory
04519072 Ametek Gemco Transformer on rectifier panel E0103026. 500 VA, 1 PH, 50 / 60 Hz, 380 to 600 Volt Primary, 115 / 230 Volt Secondary
04519135 Ametek Gemco Transformer used on a rectifier panel, 100 VA, 230 Volt PR1, 56VCT Sec., Triad FD8-56
04521186 Ametek Gemco Terminal Strip. 16 Place Terminal Strip used on programmer and output expansion module. 1995 Micro-Set PLS (<1LB)
04521187 Ametek Gemco Terminal Strip. 24 Place Terminal Strip used on programmer and output expansion module. 1995 Micro-Set PLS (<1LB)
04521210 Ametek Gemco Cable Assembly for the 950IS only. 6 Foot 2 Pin Euro Mini Straight Connector
04523020 Ametek Gemco Relay. 1996 Ram-Set & Brake Monitor Relay on a 1992 Press-Set Controller (<1LB)
04523022 Ametek Gemco Relay. Mechanical Output Relay SPDT 10 AMP, 24 VDC 1992 & 1995 PLS
04523085 Ametek Gemco Timer on Delay used on a rectifier panel, 10 Sec Plug in, 8 Pin, 240 VAC 12/6
04523126 Ametek Gemco Relay. AC Solid State Relay, 3 AMP., 24 - 280 VAC
04523127 Ametek Gemco Relay. DC Solid State Relay
04535001 Ametek Gemco Resolver. Replacement resolver with wire leads but without connector (2LBS) Size 11 Single S Kearfott CR41093052-14 or Deltran # 11BRCX-300-L10/6
04535094 Ametek Gemco Resolver. Size 11 resolver, single shaft (internal resolver only, no housing)
11-BHW-40-F/F473
04537001 Ametek Gemco Switch. Snap Switch. S.P.D.T. Single Pole Double Throw (<1LB) 1/8
04537002 Ametek Gemco Switch. Snap Switch. S.P.D.T. Single Pole Double Throw 1/8
04537003 Ametek Gemco Micro Switch DPDT. Includes Roller & Arm (<1LB) 1/8
04537004 Ametek Gemco Switch used on the 2000 Series Limit Switch Assemblies, S.P.D.T., Includes Actuator Arm with Roller and Hardware. Can be wired for normally open or closed circuit. Plunger Side Normally Open Terminals, Opposite Plunger Side Normally Closed Terminals 16-204 (<1LB) 1/8
04537018 Ametek Gemco Switch. Precision Snap Switch with 1/2 Roller. Sq D # 9007-AB1-S1. 2000 Series GRLS 1/8
04537080 Ametek Gemco Key for a 1992 Press-Set Controller & a 1989 PLS (<1LB)
04560001 Ametek Gemco Screw. Pan Head Machine Screw 6-32 x 1'' STL SLTD zinc & wax taptite (<1LB)
04562148 Ametek Gemco Jam Nut (<1LB)
04564002 Ametek Gemco Woodruff Key
04564012 Ametek Gemco Fastener. Retaining / Snap Ring. Truarc 5100-37 SZDB. Shaft to Worm Gear Fastener 200- Series
04570001 Ametek Gemco Bearing. Sealed Ball Bearing with Mounting Flanges for a 1980 Series Limit Switch. NEMA 1, 4 or 12 Enclosures. 3/4 Inch I.D. (1LB)
04570252 Ametek Gemco Rod Ends for the 956 LDT or Control Arm 955ARM Female Thread 1/4 -28
04573067 Ametek Gemco Motor 48 VDC Tach Generator
04578121 Ametek Gemco Repair Kit. Repair Kit for the Master Cylinder Section of a New Style J54085 or a J054086 Power Cluster
04578122 Ametek Gemco Repair Kit. Repair Kit for the Diaphragm on a New Style J054085 Power Cluster
04578123 Ametek Gemco Repair Kit. Repair Kit for the Diaphragm on a New Style J054086 Power Cluster
04580066 Ametek Gemco Coupling. .25 X .120 Bore . Used to connect the cam shaft and a resolver (1LB)
04581003 Ametek Gemco Spring. Return Spring on a Foot Switch (<1LB) 7/7
04582015 Ametek Gemco Belt. O-Ring Belt, Cam box main shaft to tach generator drive belt (<1LB)
10'' H 1 Ametek Gemco 10 Inch Hydraulic Type H Brake System. Provides infinitely variable progressive brake application for smooth controlled braking. 0 to 425 LBS. / FT dynamic stopping torque. Includes Qty.1, 10 Inch Hydraulic Brake Assembly, Fluid Reservoir Bleeder, Pushbutton Switch with Enclosure for operating the bleeder check valve, Control Cylinder with Foot Pedal, 100 Feet of Hydraulic Tubing, Tube Fittings, Unions, Clamps, Bushings, Brackets, Gaskets, 4 Armored Flexible Hoses & Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703. 10 Inch Brake Weight 93 LBS. Overall Width 19 - 7/16 Inch , Height 19 - 7/16 Inch. Please specify whether the Fluid Reservoir Bleeder is to be AC DC or manually operated. A 10 X 4 Inch Brake Wheel is not included. 7905 Actuator 222 LBS Gross
10'' HM 1 Ametek Gemco 10 X 4.25 Inch Hydraulic Brake System Type HM for Progressive / Controlled Stopping Torque and Parking. Torque range of 0 through 425 FT LBS. via Foot Pedal Pressure along with Spring Set Parking & Holding. Parking Torque 450 FT LBS. Includes one 10 Inch Diameter Hydraulic Brake Assembly, HM Control Unit, Parking Brake Control station with Signal Light, Foot Pedal & Control Cylinder, Fluid Reservoir / Bleeder, Bleeder Pushbutton, 150 FT Copper Hydraulic Tubing, Wagner 21B Super Heavy Duty Brake Fluid, Fittings, Gaskets and Armored Flexible Hoses. Specify whether 230 VDC or 115 VAC for the bleeder operation. A manually operated bleeder is also available. Less Brake Wheel. 220 LBS Net.
10''-H-1 Ametek Gemco 10 Inch Hydraulic Type H Brake System. Provides infinitely variable progressive brake application for smooth controlled braking. 0 to 425 LBS. / FT dynamic stopping torque. Includes Qty.1, 10 Inch Hydraulic Brake Assembly J002926 with Actuating Cylinder J007905 , Fluid Reservoir Bleeder, Pushbutton Switch with Enclosure J010008 for operating the bleeder check valve, Control Cylinder J017616 with Foot Pedal J008219, 100 Feet of Hydraulic Tubing A055980, Tube Fittings J00086 , Unions J049087, Clamps J005138, Bushings J005137, Brackets F005780, Gaskets F17, 4 Armored Flexible Hoses J010160 & Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703. 10 Inch Brake Weight 93 LBS. Overall Width 19 - 7/16 Inch , Height 19 - 7/16 Inch. Please specify whether the Fluid Reservoir Bleeder is to be AC DC or manually operated. A 10 X 4 Inch Brake Wheel is not included in this price (222LBS)
10''-H-2 Ametek Gemco Hydraulic Brake System, Complete Type H Brake System. Infinitely Progressive Braking Torque, 0 to 400 Foot LBS via Foot Pedal Pressure based on a Maximum Pedal Pressure of 70 LBS. Includes Qty. 2, 10 Inch Hydraulic Brake Assemblies J002926, Fluid Reservoir Bleeder, Bleeder Pushbutton Station J10008, Control Cylinder J017616 with Pedal J008219, J73901 Installation Kit which includes, 250 Feet of Copper Tubing, Tube clamps, Tube Bushings, Tube Fittings, Tube Unions, Tube Tee, Qty.6, Armored Hose Kits J010797 & 1 Gallon of Wagner 21B Brake Fluid F9314. Brake Wheels are not included. Please specify whether the Fluid Reservoir Bleeder is to be AC DC or manually via a 1/4 Turn Ball Valve (189LBS)
1025-1407 Ametek Gemco Foot Switch. Engineered product with a Reed Switch. Like a 1025-B-1SP-P
B = Heavy Duty NEMA 4 Treadle Operated Foot Switch
1SP = Reed Switch supplied
P = Plain Cover, covers only the enclosure 1/6
1025-1421 Ametek Gemco Foot Switch. Type C Heavy Duty NEMA 4 Side Treadle Operated Foot Switch. 2 Single Pole Double Throw Switches. ( Each 1 N.O. - 1 N.C.) with special I.D originally done for United Airlines (7LBS) 1/06
1025-1423 Ametek Gemco Foot Switch use new part number 1025-B-1SP-P-X
1025-A-1DP-S Ametek Gemco Foot Switch. Obsolete 4/1/06 see Type ''B'' Type ''A'' Standard Duty Treadle Operated Foot Switch, NEMA 1 Die Cast Enclosure, 1DP = One contact Block, 1 D.P.D.T. Double Pole Double Throw Switch, (2N.O. - 2 N.C.) 2 Position with Spring Return
. Includes Protective Shield to prevent accidental treadle operation. 3/4 Inch Conduit Entrance
(4LBS)
1025-A-1DP-X Ametek Gemco Foot Switch. Obsolete 4/1/06 see Type ''B'', Type ''A'' Standard Duty Treadle Operated Foot Switch, NEMA 1 Die Cast Enclosure, 1SP = One contact Block, 1 D.P.D.T. Single Pole Double Throw Switch, (2N.O. - 2 N.C.) 2 Position with Spring Return. 3/4 Inch Conduit Entrance (2LBS)
1025-A-1SP-S Ametek Gemco Foot Switch. Obsolete 4/1/06 see Type ''B'' Type ''A'' Standard Duty Treadle Operated Foot Switch, NEMA 1 Die Cast Enclosure, 1SP = One contact Block, 1 S.P.D.T. Single Pole Double Throw Switch, (1N.O. - 1 N.C.) 2 Position with Spring Return. Includes Protective Shield to prevent accidental treadle operation. 3/4 Inch Conduit Entrance (4LBS)
1025-A-1SP-X Ametek Gemco Foot Switch. Obsolete 4/1/06 see Type ''B'',Type ''A'' Standard Duty Treadle Operated Foot Switch, NEMA 1 Die Cast Enclosure, 1SP = One contact Block, 1 S.P.D.T. Single Pole Double Throw Switch, (1N.O. - 1 N.C.) 2 Position with Spring Return. 3/4 Inch Conduit Entrance.
1025-B-1A4-S-X Ametek Gemco Foot Switch. Heavy Duty NEMA 4 Treadle Foot Switch.
1A4 = 4 Way 5 Port, 1 Air Valve
S = Treadle Shield for Top & Side Switch Protection
X = No Switch Latch
1025-B-1DP-P-X Ametek Gemco Foot & Palm Switches. Series 1025 Type B Heavy Duty NEMA 4 Treadle Operated Foot Switch. 1 Contact Block 1 D.P.D.T. Switch that can be wired for a normally open or closed circuit. Only the enclosure is covered. The foot pedal is not covered (5LBS)
1025-B-1DP-S-X Ametek Gemco Foot Operated Switch
B = Heavy Duty NEMA 4 Treadle Operated Foot Switch
1DP = One D.P.D.T. Double Pole Double Throw Switch which can be wired for either Normally Open or Normally Closed Circuits
S = Treadle Shield for Top & Side Protection
1025-B-1SP-G-X Ametek Gemco Foot Operated Switches, Type ''B'' Heavy Duty Treadle operated foot switch. NEMA 4, Two contact blocks, 1 SPDT ( 1 NO - 1NC ) with Treadle Guard to provide top protection from accidental operation
1025-B-1SP-P-X Ametek Gemco Foot & Palm Switches. Series 1025 Type B Heavy Duty NEMA 4 Treadle Operated Foot Switch. 1 Contact Block 1 S.P.D.T. Switch that can be wired for a normally open or closed circuit. Only the enclosure is covered. The foot pedal is not covered (5LBS)
1025-B-1SP-S-X Ametek Gemco Foot Operated Switches, Type ''B'' Heavy Duty Treadle Operated Foot Switch. NEMA 4, One contact block, 1 SPDT ( One 1 NO - 1NC ), S Cover Option = Treadle Shield provides Top & Side Protection C-H 10251-H35C with Switch Type B (8LBS)
1025-B-1SP-U-X Ametek Gemco Foot Operated Switches, Type ''B'' Heavy Duty Treadle Operated Foot Switch. NEMA 4, One contact block, 1 SPDT ( One 1 NO - 1NC ), U Cover Option = Treadle Shield provides Top, Side and a Safety Gate which must be raised by the toe to gain access to the treadle (11LBS)
1025-B-2DP-P-X Ametek Gemco Foot Operated Switch
B = Heavy Duty NEMA 4 Treadle Operated Foot Switch
2DP = Two D.P.D.T. Double Pole Double Throw Switches which can be wired for either Normally Open or Normally Closed Circuits
X = No other options
1025-B-2DP-S-L Ametek Gemco Foot Operated Switch.
B = Heavy Duty NEMA 4 Treadle Operated Foot Switch
2DP = Two D.P.D.T. Double Pole Double Throw Switches which can be wired for either Normally Open or Normally Closed Circuits
S = Treadle Shield for Top & Side Protection
L = Protective Shield
1025-B-2DP-S-X Ametek Gemco Foot Operated Switch
B = Heavy Duty NEMA 4 Treadle Operated Foot Switch
2DP = Two D.P.D.T. Double Pole Double Throw Switches which can be wired for either Normally Open or Normally Closed Circuits
S = Treadle Shield for Top & Side Protection
1025-B-2SP-G-X Ametek Gemco Foot Operated Switches, Type ''B'' Heavy Duty Treadle operated foot switch. NEMA 4, Two contact blocks, 2 SPDT ( Each 1 NO - 1NC ) with Treadle Guard to provide top protection from accidental operation
1025-B-2SP-P-X Ametek Gemco Foot & Palm Switches. Series 1025 Type B Heavy Duty NEMA 4 Treadle Operated Foot Switch. 2 Contact Blocks, 2 S.P.D.T. Switches that can be wired for a normally open or closed circuits. Only the enclosure is covered. The foot pedal is not covered (5LBS)
1025-B-2SP-S-X Ametek Gemco Foot Operated Switches, Type ''B'' Heavy Duty Treadle operated foot switch. NEMA 4, Two contact blocks, 2 SPDT ( Each 1 NO - 1NC ) with Treadle Shield providing Top & Side Guard protection from accidental operation
1025-C-2DP-S Ametek Gemco Foot Operated Switch, Type C Heavy Duty Side Treadle, NEMA 4 Water and Oiltight Enclosure has a Die Cast Aluminum Case, Cover & Treadle. Two Contact Blocks, 2 D.P.D.T. Switches (Each 2 NO - 2 NC) with Protective Shields. Six nameplates are provided, ''START'' ''STOP'' ''FORWARD'' ''REVERSE'' two are blank for special markings. Case has Qty. 2, 3/4'' pipe tapped conduit entrances one of which is fitted with a pipe plug. (12LBS)
1025-C-2DP-X Ametek Gemco Foot Operated Switch, Type C Heavy Duty Side Treadle, NEMA 4 Water and Oiltight Enclosure has a Die Cast Aluminum Case & Treadle. Two Contact Blocks, 2 D.P.D.T. Switches (Each 2 NO - 2 NC) Six nameplates are provided, ''START'' ''STOP'' ''FORWARD'' ''REVERSE'' two are blank for special markings. Case has Qty. 2, 3/4'' pipe tapped conduit entrances one of which is fitted with a pipe plug. (11LBS)
1025-C-2SP-S Ametek Gemco Foot Operated Switch, Type C Heavy Duty Side Treadle, NEMA 4 Water and Oiltight Enclosure has a Die Cast Aluminum Case, Cover & Treadle. Two Contact Blocks, 2 S.P.D.T. Switches (Each 1 NO - 1 NC) with Protective Shields. Six nameplates are provided, ''START'' ''STOP'' ''FORWARD'' ''REVERSE'' two are blank for special markings. Case has Qty. 2, 3/4'' pipe tapped conduit entrances one of which is fitted with a pipe plug (11LBS)
1025-C-2SP-X Ametek Gemco Switch. Foot Operated Switches, Type ''C'' Heavy Duty Side Treadle Operated Foot Switch. NEMA 4 Enclosure, Two Contact Blocks, Two Snap action Single Pole Double Throw Switches that can be wired for either Normally Open or Normally Closed Circuits. Six Name Plates are provided. START STOP FORWARD REVERSE & Two are blank for your custom marking (7LBS)
1025-D-1SP Ametek Gemco Foot and Palm Operated Switch. Type D with a Large Orange Mushroom Button 5 Inches in Diameter which is well suited for critical applications where a large easy to see operator is required. NEMA Type 1 Enclosure has a die cast aluminum case and operating button. One S.P.D.T. Switch (1 NO - 1 NC) Case has a Qty. of 2, 3/4 inch pipe tapped conduit entrances one of which is fitted with a pipe plug (4LBS)
1025-D-2DP Ametek Gemco Foot and Palm Operated Switch. Type D with a Large Orange Mushroom Button 5 Inches in Diameter which is well suited for critical applications where a large easy to see operator is required. NEMA Type 1 Enclosure has a die cast aluminum case and operating button. Two D.P.D.T. Switch (2 NO - 2 NC) Case has a Qty. of 2, 3/4 inch pipe tapped conduit entrances one of which is fitted with a pipe plug (4LBS)
1025-D-2SP Ametek Gemco Foot and Palm Operated Switch. Type D with a Large Orange Mushroom Button 5 Inches in Diameter which is well suited for critical applications where a large easy to see operator is required. NEMA Type 1 Enclosure has a die cast aluminum case and operating button. One D.P.D.T. Switch (2 NO - 2 NC) Case has a Qty. of 2, 3/4 inch pipe tapped conduit entrances one of which is fitted with a pipe plug (4LBS)
10316H-169-1 Ametek Gemco 2006-402-L-1080-A
10316H89A Ametek Gemco 1950-1-B-A-DO C-H Part # shown above
104A020XXXX Ametek Gemco Thermistors. 9967 LUG Thermistor. MOTOGARD Controllers are designed for use with Positive Temperature Coefficient Thermistors. Thermistor is encapsulated in a special epoxy for rugged mechanical duty, severe environments and good thermal conductivity# 22 - 26 Teflon Insulated Leads. Specify desired length of the leads (<1LB)
104A022XXXX Ametek Gemco Thermistors. 9967 SPRING LOADED PROBE Thermistor. MOTOGARD Controllers are designed for use with Positive Temperature Coefficient Thermistors. Thermistor is encapsulated in a special epoxy for rugged mechanical duty, severe environments and good thermal conductivity# 22 - 26 Teflon Insulated Leads. 7/16 Inch Diameter. 1/4 Inch NPT. Specify desired probe length, 2 to 6 Inches is standard. Specify lead length (<1LB)
107085 Ametek Gemco Repair Kit, for a Moisture Ejection Valve. ISG SAP 1170357
107163002 Ametek Gemco Pressure Cluster Assembly, 1 X 8, with special piston for long static lines, like 54086
1090-A1 Ametek Gemco Obsolete 12 Bit unit. Replaced by 1090B1 a 14 Bit unit
1090B1 Ametek Gemco Multibus High Speed Programmable Limit Switch. 14 Bit Resolution. Replaced 1090A1
115101-2 Ametek Gemco MOTOGARD 9966. Series 115 Over Temperature Protection System. 6 Inputs, 2 Triac Outputs 1-N.O. 1 N.C. Input Rating: 120 VAC + or - 10% Single Phase 50/60 Hz. Output Rating: 120 /240 Volts 5 amp continuous. Reset is automatic. Enclosure 5.5'' Wide X 4.25'' Long X 3.12'' High Potted in a NEMA 4 Steel Case (2LBS)
120101 Ametek Gemco MOTOGARD 9966. Series 120 Over Temperature Protection System
135101 Ametek Gemco MOTOGARD 9966. Series 135 Over Temperature Protection System
14'' H 2 Ametek Gemco 14 Inch Hydraulic Brake System, Qty. 2, Brake Assemblies each capable of 0 to 600 LBS / FT Torque, Control Cylinder, Pedal, Fluid Reservoir Bleeder, 250 Foot of Tubing, 6 Armored Hoses, 3 Gallons of 21B Wagner Brake Fluid and Fittings, 6 Brackets, 6 Jam Nuts, 36 Tube Nuts, 6 Lock Washers, 15 Copper Gaskets, 85 Bushings, 85 Clamps, 7 Unions for a complete system, less brake wheels.
14'' HM 1 Ametek Gemco 14 X 6.50 Inch Hydraulic Brake System Type HM for Progressive / Controlled Stopping Torque and Parking. Torque range of 0 through 600 FT LBS. via Foot Pedal Pressure along with Spring Set Parking & Holding. Parking Torque 550 FT LBS. Includes one 14 Inch Diameter Hydraulic Brake Assembly, HM Control Unit, Parking Brake Control Station with Signal Light, Foot Pedal & Control Cylinder, Fluid Reservoir / Bleeder, Bleeder Pushbutton, 150 FT Copper Hydraulic Tubing, Wagner 21B Super Heavy Duty Brake Fluid, Fittings, Gaskets and Armored Flexible Hoses. Specify whether 230 VDC or 115 VAC for the bleeder operation. A manually operated bleeder is also available. Less Brake Wheel. 289 LBS Net.
14''-H-1 Ametek Gemco 14 Inch Hydraulic Type H Brake System. Provides infinitely variable progressive brake application for smooth controlled braking. 0 to 600 LBS. / FT dynamic stopping torque. Includes Qty.1, 14 Inch Hydraulic Brake Assembly, DC Fluid Reservoir Bleeder, Control Cylinder with Foot Pedal, 100 Feet of Hydraulic Tubing, Tube Fittings, Unions, Clamps, Bushings, Brackets, Gaskets, 4 Armored Flexible Hoses & Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703. 14 Inch Brake Weight 161 LBS. Overall Width 25 - 7/8 Inch, Height 28 - 1/2 Inch. A 7905 Brake Actuator is provided / used on a single brake system (320LBS)
1500-H-L3-S9-N1-X Ametek BW Controls Induction Control Relay model 1500-H-L3-S9-N1-X, 440 VAC Line Voltage, 480VAC Secondary Voltage, Nema 1 Enclosure without any other options.
1500-HL1-S30-C-X Ametek BW Controls Relay. Series 1500 Induction Control Relay. 110 volts Primary, 40 Volts Secondary
1500F-L1-S7OCX Ametek BW Controls Induction Control Relay
150101 Ametek Gemco MOTOGARD 9966. Series 150 Over Temperature Protection Systems provide immediate overheating protection for motors equipment enclosures, semiconductor heatsinks, sleeve bearings and other related machinery. For use with PTC Thermistors embedded in or in contact with the monitored surface. 1 Input, Form C Relay Output. 2 Triac Outputs 1-N.O. 1 N.C. Input Rating: 120 VAC + or - 10% Single Phase 50/60 Hz. Output Rating: 120 VAC for size 5 contactor coil. Reset is automatic. Enclosure 3.25'' Wide X 2.25'' Long X 2.50'' High. Potted in a polyester case. Conforms with NEC Requirements for integral motor thermal protection (1LB)
16-204 Ametek Gemco Switch see AME-04537004
1746L-1 Ametek Gemco LDT Interface Card. Single Axis, One LDT Input. Specify LDT output if other than: CP, VPI or RS (2LBS)
1746L-2 Ametek Gemco LDT Interface Card. Two Axis, Two LDT Inputs. Specify LDT output if other than: CP, VPI or RS (2LBS)
1746R-1 Ametek Gemco Interface Card. Series 1746R Resolver Interface Card incorporates Allen-Bradley licensed technology for complete compatibility with A-B Series 1746 I/O Chassis. The unit monitors machine position from a resolver and delivers continues absolute position data at 12 bit (4,096 count) resolution and RPM data to the SLC processor.
1746R-2 Ametek Gemco Interface Card. Series 1746R Resolver Interface Card incorporates Allen-Bradley licensed technology for complete compatibility with A-B Series 1746 I/O Chassis. The unit monitors machine position from a resolver and delivers continues absolute position data at 12 bit (4,096 count) resolution and RPM data to the SLC processor. Two axis resolver interface. Two resolver inputs or field configurable for one multi-turn dual resolver.
17618 Ametek Gemco Washer on Spring Case Gasket Kit
1771-PLS-B1 Ametek Gemco Ultra-High Speed Programmable Limit Switch (PLS) with 16 direct outputs from the front panel that update every 5 microseconds. A resolver based unit that incorporated Allen-Bradley technology and is completely compatible with the A-B Series 1771 I/O chassis. Internally powered by the PLC backplane. Resolver input with 14 bit (16,384 count) resolution and field programmable scale factor. Reset to Preset Inputs & Speed Compensation. This product incorporates patented technology which is licensed by Allen -Bradley Company Inc. Allen-Bradley is a registered trademark of Rockwell Corporation (3LBS)
1771-PLS-C1 Ametek Gemco Programmable Limit Switch. Allen Bradley Series 1771 Compatible High Speed Programmable Limit Switch. Standard 14 Bit Resolution (4LBS)
18'' H-2 Ametek Gemco Hydraulic Brake System, Complete Type H Brake System. Infinitely Progressive Braking Torque, 0 to 1800 Foot LBS via Foot Pedal Pressure based on a Maximum Pedal Pressure of 70 LBS. Includes Qty. 2, 18 Inch Hydraulic Brake Assemblies J002932, Fluid Reservoir Bleeder, Bleeder Pushbutton Station J10008, Control Cylinder J017616 with Pedal J008219, Installation Kits J07300 &J073903 which includes, 250 Feet of Copper Tubing, 85 Tube Clamps, 85 Tube Bushings, 36 Tube Fittings, 7 Tube Unions, 1 Tube Tee, Qty.6, Armored Hose Kits J010797 & 4 Gallons of Wagner 21B Brake Fluid F9314. Brake Wheels are not included. Please specify whether the Fluid Reservoir Bleeder is to be AC DC or manually via a 1/4 Turn Ball Valve (670LBS)
18'' HM 1 Ametek Gemco 18 X 8.50 Inch Hydraulic Brake System Type HM for Progressive / Controlled Stopping Torque and Parking. Torque range of 0 through 900 FT LBS. via Foot Pedal Pressure along with Spring Set Parking & Holding. Parking Torque 700 FT LBS. Includes one 18 Inch Diameter Hydraulic Brake Assembly, HM Control Unit, Parking Brake Control Station with Signal Light, Foot Pedal & Control Cylinder, Fluid Reservoir / Bleeder, Bleeder Pushbutton, 150 FT Copper Hydraulic Tubing, Wagner 21B Super Heavy Duty Brake Fluid, Fittings, Gaskets and Armored Flexible Hoses. Specify whether 230 VDC or 115 VAC for the bleeder operation. A manually operated bleeder is also available. Less Brake Wheel. 389 LBS Net.
18''-H-1 Ametek Gemco Hydraulic Brake System, Complete Type H Brake System. Infinitely Progressive Braking Torque, 0 to 900 Foot LBS via Foot Pedal Pressure based on a Maximum Pedal Pressure of 70 LBS. Includes Qty.1, 18 Inch Hydraulic Brake Assembly J002932, Fluid Reservoir Bleeder, Bleeder Pushbutton Station J10008, Control Cylinder J017616 with Pedal J008219, J73901 Installation Kit which includes, 100 Feet of Copper Tubing, Tube clamps, Tube Bushings, Tube Fittings, Tube Unions, Tube Tee, Qty.4, Armored Hose Kits J010797 & 1 Gallon of Wagner 21B Brake Fluid F9314. A Brake Wheel is not included. Please specify whether the Fluid Reservoir Bleeder is to be AC DC or manually via a 1/4 Turn Ball Valve (359LBS)
1950-1-B-A-AO Ametek Gemco Switch
1950 = Precision, Snap Action, Switch Assembly Mfg by Gemco
1 = Single Pole Double Throw / S.P.D.T., Four Screw Terminals, can be wired for either a Normally Open or Normally Close Circuit
B = Binder / Screw Terminals 4
A = Front Mounting
AO = Switch Plunger operated via cam or roller follower
U.L. Listed, 15 AMPS, 110 - 600 Volts AC / DC
-50 to 185 Degree F
Recommended replacement @ 15 million cycles
(<1LB)
1950-1-B-A-AR Ametek Gemco Switch
1950 = Precision, Snap Action, Switch Assembly Mfg by Gemco
1 = Single Pole Double Throw / S.P.D.T., Four Screw Terminals, can be wired for either a Normally Open or Normally Close Circuit
B = Binder / Screw Terminals 4
A = Front Mounting
A = Switch Plunger operated via cam or roller follower
R = Rubber boot for addition protection form humidity and dust
U.L. Listed, 15 AMPS, 110 - 600 Volts AC / DC
-50 to 185 Degree F
Recommended replacement @ 15 million cycles
(<1LB)
1950-1-B-A-BO Ametek Gemco Switch. Precision Snap Limit Switch Unit, Single Pole Double Throw (S.P.D.T.), 1 NO - 1NC Contacts, Front Mounting, Lever & 1/2'' Dia. Roller Assembly
1950-1-B-A-DO Ametek Gemco Switch. Precision Snap Action Switch Assembly. SPDT Single Pole Double Throw, Qty. 4 Screw Terminals, can be wired for either a Normally Open or Normally Close Circuit, Front Mounting, Plunger Push Operator, 2006 Type K, U.L. Listed (<1LB)
1950-1-B-A-DR Ametek Gemco Switch. Precision Snap Action Switch Assembly. 1 = Single Pole Double Throw / S.P.D.T., Four Screw Terminals, can be wired for either a Normally Open or Normally Close Circuit, B = Binder Terminals, A = Front Mounting, DR = Plunger with Boot, Push Operated, U.L. Listed (<1LB)
1950-1-C-A-BO Ametek Gemco Switch. Precision Snap Limit Switch Unit, Single Pole Double Throw (S.P.D.T.), 1 NO - 1NC Contacts, 915 / 917 Cycl-Set Terminals, Front Mount, Lever & 1/2 Inch Diameter Roller Assembly.
1950-1-C-A-DO Ametek Gemco Switch. Precision Snap Action Limit Switch Assembly, Single Pole Double Throw / S.P.D.T., 4 screw terminals, can be wired for either Normally Open or Normally Closed Circuits. Front Mount, Plunger Push Operator. 915 / 917 Cycl-Set & 2006 K RS (<1LB)
1950-1-D-A-AO Ametek Gemco Switch. Precision Snap Limit Switch Unit, Single Pole Double Throw (S.P.D.T.), 1 NO - 1NC Contacts, Saddle Clamp Terminals, Front Mounting, Plunger Cam Operated
1950-1-D-A-DO Ametek Gemco Switch. Precision Snap Limit Switch Unit, Single Pole Double Throw (S.P.D.T.), 1 NO - 1NC Contacts, Saddle Clamp Terminals, Front Mounting, Plunger Push Operator ( Cycl-Set & 2006K RS )
1950-1-P-A-AO Ametek Gemco Switch. Precision Snap Limit Switch Unit, Single Pole Double Throw (S.P.D.T.), 1 NO - 1NC Contacts, Plug-In Terminals, Front Mounting, Plunger Cam Operated
1950-1-P-A-AR Ametek Gemco Switch. Precision Snap Limit Switch Unit, Single Pole Double Throw (S.P.D.T.), 1 NO - 1NC Contacts, Plug-In Terminals, Front Mounting, Plunger Cam Operated, Plunger with boot-cam operator.
1950-1404 Ametek Gemco Switch. Precision Snap Limit Switch Unit. Single Pole Double Throw (S.P.D.T.) Plunger OP Bind TE with Boot and Heavy Springs. For use with the Series 1970 Driv Cheks (<1LB)
1950-1405 Ametek Gemco Switch. Precision Snap Limit Switch Unit. Double Pole Double Throw, Plunger Operated. Binder Terminals with Heavy Springs. 1970 Drive Chek (<1LB)
1950-1406 Ametek Gemco Switch. Obsoleted in 2006, See 1950-1413. Precision SPST Slow Make - Slow Break Switch Assembly. N.C. Normally Closed. Special Purpose Switch. U.L. Listed For the 1980 Product Line (<1LB)
1950-1408 Ametek Gemco Switch. SPDT Slow Make Slow Break. For products 915 / 917/ 2006 (<1LB)
1950-1413 Ametek Gemco Switch. Precision Slow Make - Slow Break Single Pole Double Throw Switch Assembly. Can be wire for either a normally open or normally close circuit. 4 screw terminals on this switch. Replaces 1950-1406 which is obsolete (<1LB)
1950-1414 Ametek Gemco Switch. Single Pole Double Throw with a Heavy Duty Spring for high vibration applications. Can be wired for normally open or closed circuits, 4 screw terminals. Replaces obsolete 1950-1416 but is not a Slow Make Slow Break Switch (<1LB)
1950-1416 Ametek Gemco Switch. Obsolete 1/6 Precision Snap Switch, Single Pole Double Throw, Slow Make Slow Break with a Heavy duty / strong Spring for High Vibration Applications. Only one contact that is Normally Closed. Replaced by 1950-1414, though it is NOT an exact duplicate replacement, see specifications (<1LB)
1950-4-B-A-AO Ametek Gemco Switch
1950 = Precision, Snap Action, Switch Assembly Mfg by Gemco
4 = Double Pole Double Throw / D.P.D.T., Eight Screw Terminals, can be wired for either a Normally Open or Normally Close Circuits
B = Binder / Screw Terminals 8
A = Front Mounting
AO = Switch Plunger operated via cam or roller follower
U.L. Listed, 15 AMPS, 110 - 600 Volts AC / DC
-50 to 185 Degree F
Recommended replacement @ 15 million cycles
(<1LB)
1950-4-B-A-AR Ametek Gemco Switch
1950 = Precision, Snap Action, Switch Assembly Mfg by Gemco
4 = Double Pole Double Throw / D.P.D.T., Eight Screw Terminals, can be wired for either a Normally Open or Normally Close Circuits
B = Binder / Screw Terminals 8
A = Front Mounting
A = Switch Plunger operated via cam or roller follower
R = Rubber boot for addition protection form humidity and dust
U.L. Listed, 15 AMPS, 110 - 600 Volts AC / DC
-50 to 185 Degree F
Recommended replacement @ 15 million cycles
(<1LB)
1950-4-B-A-BR Ametek Gemco Switch. Precision Snap Limit Switch Unit. Double Pole Double Throw (D.P.D.T.) 2-NO / 2-NC, Plunger operated by Lever & 1/2 Inch Diameter Roller Assembly. Includes Boot
1950-4-B-A-DO Ametek Gemco Switch. Precision Snap Action Switch Assembly. DPDT Double Pole Double Throw, Qty. 8 Screw Terminals, can be wired for either a Normally Open or Normally Close Circuit, Front Mounting, Plunger Push Operator, 2006 Type K, U.L. Listed (<1LB)
1950-4-C-A-DO Ametek Gemco Switch. Precision Snap Action Limit Switch Assembly. Double Pole Double Throw / D.P.D.T., Eight Screw Terminals, can be wired for either Normally Open or Normally Closed Circuits.Front Mount, Plunger Push Operator. 915 / 917 Cycl-Set & 2006 K RS (<1LB)
1950-4-P-A-AO Ametek Gemco Switch. Precision Snap Limit Switch Unit. D.P.D.T. Double Pole Double Throw 2-N.O 2-N.C , Plug-In Type Binder, Front Mounting Arrangement, Plunger Cam Operated.
1950G-1-B-A-AR Ametek Gemco Switch. Precision Snap Limit Switch Unit with Gold Contacts, Single Pole Double Throw (S.P.D.T.), 1 NO - 1NC Contacts, Front Mounting, Plunger with Boot, Cam Operated U.L. Listed (<1LB) 1/8
1970-104 Ametek Gemco Drive Chek for Series 1980 Rotating Cam Limit Switches. For a 2 to 4 Circuit Cam Box with a NEMA 1 Enclosure. The Drive-Chek is a multi-purpose sub base that is mounted under a chain or drive belt driven mechanism. The Drive-Chek can detect a broken chain or belt via a supplied travel limit switch is a , spring loaded sub base for chain or belt tensioning and a shock and vibration isolator (9LBS)
1970-106 Ametek Gemco Drive Chek for Series 1980 Rotating Cam Limit Switches. For a 5 to 6 Circuit Cam Box with a NEMA 1 Enclosure. The Drive-Chek is a multi-purpose sub base that is mounted under a chain or drive belt driven mechanism. The Drive-Chek can detect a broken chain or belt via a supplied travel limit switch is a , spring loaded sub base for chain or belt tensioning and a shock and vibration isolator (13LBS)
1970-108 Ametek Gemco Drive Chek for Series 1980 Rotating Cam Limit Switches. For a 7 to 8 Circuit Cam Box with a NEMA 1 Enclosure. The Drive-Chek is a multi-purpose sub base that is mounted under a chain or drive belt driven mechanism. The Drive-Chek can detect a broken chain or belt via a supplied travel limit switch is a , spring loaded sub base for chain or belt tensioning and a shock and vibration isolator (16LBS)
1970-112 Ametek Gemco Drive Chek for Series 1980 Rotating Cam Limit Switches. For a 9 to 12 Circuit Cam Box with a NEMA 1 Enclosure. The Drive-Chek is a multi-purpose sub base that is mounted under a chain or drive belt driven mechanism. The Drive-Chek can detect a broken chain or belt via a supplied travel limit switch is a , spring loaded sub base for chain or belt tensioning and a shock and vibration isolator (19LBS)
1970-116 Ametek Gemco Drive Chek for Series 1980 Rotating Cam Limit Switches. For a 13 to 16 Circuit Cam Box with a NEMA 1 Enclosure. The Drive-Chek is a multi-purpose sub base that is mounted under a chain or drive belt driven mechanism. The Drive-Chek can detect a broken chain or belt via a supplied travel limit switch is a , spring loaded sub base for chain or belt tensioning and a shock and vibration isolator
1970-120 Ametek Gemco Drive Chek for Series 1980 Rotating Cam Limit Switches. For a 17 or 20 Circuit Cam Box with a NEMA 1 Enclosure. The Drive-Chek is a multi-purpose sub base that is mounted under a chain or drive belt driven mechanism. The Drive-Chek serves 3 purposes; a broken chain or belt detector via a supplied travel limit switch, spring loaded sub base for chain or belt tensioning and a shock and vibration isolator
1970-1204 Ametek Gemco Drive Chek. Drive Check for a Series 1980 Rotating Cam Limit Switch. 2 to 4 Circuit Frame with a NEMA 4 / 12 Enclosure. The Drive-Chek is a multi-purpose sub base that is mounted under a chain or drive belt driven mechanism. The Unit serves 3 purposes; a broken chain or belt detector, a chain or belt tightener and a shock / vibration isolator
1970-1206 Ametek Gemco Drive Chek. Drive Check for a Series 1980 Rotating Cam Limit Switch. 5 to 6 Circuit Frame with a NEMA 4 / 12 Enclosure. The Drive-Chek is a multi-purpose sub base that is mounted under a chain or drive belt driven mechanism. The Unit serves 3 purposes; a broken chain or belt detector, a chain or belt tightener and a shock / vibration isolator
1970-1208 Ametek Gemco Drive Chek. Drive Check for a Series 1980 Rotating Cam Limit Switch. 7 to 8 Circuit Frame with a NEMA 4 / 12 Enclosure. The Drive-Chek is a multi-purpose sub base that is mounted under a chain or drive belt driven mechanism. The Unit serves 3 purposes; a broken chain or belt detector, a chain or belt tightener and a shock / vibration isolator
1970-1212 Ametek Gemco Drive Chek. Drive Check for a Series 1980 Rotating Cam Limit Switch. 5 to 6 Circuit Frame with a NEMA 12 Enclosure. The Drive-Chek is a multi-purpose sub base that is mounted under a chain or drive belt driven mechanism. The Unit serves 3 purposes; a broken chain or belt detector, a chain or belt tightener and a shock / vibration isolator
1970-124 Ametek Gemco Drive Chek for Series 1980 Rotating Cam Limit Switches. For a 21 to 24 Circuit Frame with a NEMA 1 Enclosure. The Drive-Chek is a multi-purpose sub base that is mounted under a chain or drive belt driven mechanism. The Unit serves 3 purposes; a broken chain or belt detector, a chain or belt tightener and a shock or vibration isolator.
1980 Ametek Gemco Series 1980 Micro-Adjust Rotating Cam Limit Switch
Switch Settings 4 to 356 Degrees without a Tool - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
Model 1980-106-R-DP-X
1 = NEMA 1 Enclosure
6 = Qty. 6, Independent Cams / Circuits / Switches
R = Right Hand Shaft Extension
DP = DPDT Switches = Double Pole Double Throw
X = No Timing Dial or timing dial window

CAPE MAY NEW JERSEY MOVEABLE BRIDGE;
Specification for rotating cam limit switch.

The contractor shall provide a rotating cam limit switch that meets the specification as called out below.
The cam box shall have 16 circuits each consisting of a micro adjust cam capable of dwells from 4 degrees through 356 degrees utilizing two cam halves.
The cams shall be adjusted by use of a cam adjustment tool supplied with the cam box and mounted inside of the enclosure on a bracket.
The cams are adjusted through a 36:1 ratio pinion assembly that will rotate each half of a circuit cam 10 degrees for each complete adjustment hub turn.
The micro-adjust cams shall maintain an accuracy and repeatability of 1/4 degree.
Each circuit shall have a precision rugged duty snap action switch with double break contacts that are actuated at a uniform rate to give long life.
Electrical switches shall be SPDT with one NO and one NC contact per switch.
Switches shall be rated for at least 15 million cycles.
The input shaft shall be a 3/4'' diameter made of 316 Stainless Steel having a # 606 woodruff key and can be located on the right end, left end or a double ended version can be specified.
The enclosure, cover, latches, bearing flanges and flange bolts shall be constructed of 304 Stainless Steel meeting a NEMA 4X rating.
The cam box shall utilize lifetime sealed ball bearings for the input shaft.
The cam box shall be supplied standard with a three year warranty covering the entire unit.
The cam box shall be manufactured by Ametek APT, Gemco division out of Clawson Michigan with no substitutions allowed.
1980-101-R-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-101-R-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
01 = 1 Independent Cam / Circuit / Switch
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial or Dial Window is to be provided
3 Year Warranty
(10LBS)
1980-102-L-DP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-102-L-DP-X
Series 1980
1 = NEMA 1 Enclosure
02 = 2 Independent Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
DP = DPDT Switches / Double Pole Double Throw Snap Action Switch U.L. Listed
X = No Timing Dial or Dial Window is provided
3 Year Warranty
(11 LBS)
1980-102-L-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-102-L-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
02 = 2 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
L = Left Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(11LBS)
1980-102-R-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-102-R-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
02 = 2 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
1980-103-L-DP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-103-L-DP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
03 = 3 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
L = Left Hand Shaft Extension from Enclosure
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuits. 8 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD1 = Timing Dial Labeled for C.W. Rotation
3 Year Limited Warranty
(11LBS)
1980-103-L-DP-TD2 Ametek Gemco Rotating Cam Limit Switch Model 1980-103-L-DP-TD2
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
03 = 3 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
L = Left Hand Shaft Extension from Enclosure
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuits. 8 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD2 = Timing Dial Labeled for C.C.W. Rotation
3 Year Limited Warranty
(11LBS)
1980-103-L-DP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-103-L-DP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
03 = 3 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
L = Left Hand Shaft Extension from Enclosure
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 8 screw terminals per switch
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(12LBS)
1980-103-L-GSP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-103-L-GSP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
03 = 3 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
L = Left Hand Shaft Extension
GSP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch. With Gold Plated Contacts
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
1980-103-L-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-103-L-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
03 = 3 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
L = Left Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(11LBS)
1980-103-R-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-103-R-SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
03= 3 Independent Cams / Circuits / Switches
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
TD1 = Timing Dial Labeled for Clockwise Rotation
3 Year Warranty
(12LBS)
1980-103-R-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-103-R-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
03= 3 Independent Cams / Circuits / Switches
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial or Dial Window is to be provided
3 Year Warranty
(12LBS)
1980-104-D-DP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-104-D-DP-X
Series 1980
1 = NEMA 1 Enclosure
4 = 4 Cams / Circuits / Switches
D = Double Shaft Extension from enclosure
DP = DPDT Switches / Double Pole Double Throw
X = No Timing Dial or Dial Window is provided
(13LBS)
1980-104-D-DPP-R-X-S-200-R Ametek Gemco Rotating Cam Limit Switch Model 1980-104-D-DPP-R-X-S-200-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
D = Shaft Extension Opposite the Gear Box, Double Shaft 2
DPP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch with a Plug in Socket
R = Rubber boot Option on the switch plunger for additional moisture & dust protection
X = No Timing Dial
S= Straight Drive Gear Reducer
200 = 200 to 1 Gear Ratio
R = Right End Gear Reducer
1980-104-D-GSP-R-X Ametek Gemco Rotating Cam Limit Switch like Model 1980-104-L-GSP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
L = Left Hand Shaft Extension
GSPR = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch. With Gold Plated Contacts & Rubber Seals for additional dust & moisture protection
X = No Timing Dial or Dial Window is to be provided (12LBS)
1980-104-D-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-104-D-SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
D = Dual Shafts Extending from Enclosure, 2
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD1 = Timing Dial Labeled for C.W. Rotation
3 Year Limited Warranty
(14LBS)
1980-104-D-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-104-D-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
D = Double Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial or Dial Window is provided
3 Year Warranty
(12LBS)
1980-104-L-DP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-104-L-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
L = Left Hand Shaft Extension from Enclosure
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 8 screw terminals per switch
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(12LBS)
1980-104-L-GSP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-104-L-GSP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
L = Left Hand Shaft Extension
GSP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch. With Gold Plated Contacts
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
1980-104-L-SP-R-X Ametek Gemco Rotating Cam Limit Switch Model 1980-104-L-SP-R-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
L = Left Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
R = Rubber Boot / Seal on the Switch Plunger for additional moisture protection
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(12LBS)
1980-104-L-SP-TD2 Ametek Gemco Rotating Cam Limit Switch Model 1980-104-L-SP-TD2
Series 1980
1 = NEMA 1 Enclosure
4 = 4 Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw
TD2 = Timing Dial C.C.W. Counter Clock Wise Rotation
1980-104-L-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-104-L-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
L = Left Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(12LBS)
1980-104-R-DP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-104-R-DP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
4 = 4 Independent Cams / Circuits / Switches
R = Right Hand Shaft Extension from Enclosure
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 8 screw terminals per switch
X = No Timing Dial or Dial Window is to be provided
3 Year Warranty
(12LBS)
1980-104-R-SP-R-X Ametek Gemco Rotating Cam Limit Switch Model 1980-104-R-SP-R-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
R = Rubber Boot / Seal on the Switch Plunger for additional moisture & dust protection
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(12LBS)
1980-104-R-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-104-R-SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD1 = Timing Dial Labeled for C.W. Rotation
3 Year Limited Warranty
(12LBS)
1980-104-R-SP-TD2 Ametek Gemco Rotating Cam Limit Switch Model 1980-104-R-SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD1 = Timing Dial Labeled for C.W. Rotation
3 Year Limited Warranty
(12LBS)
1980-104-R-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-104-R-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(12LBS)
1980-104-X-DP-X-S-10-R Ametek Gemco Rotating Cam Limit Switch Model 1980-104-X-DP-X-S-10-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch
X = No Timing Dial
S= Straight Drive Gear Reducer
10 = 10 to 1 Gear Ratio
R = Right End Gear Reducer
(18LBS)
1980-104-X-DP-X-S-1000-R Ametek Gemco Rotating Cam Limit Switch Model 1980-104-X-DP-X-S-1000-R1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
4 = 4 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch
X = No Timing Dial
S= Straight Drive Gear Reducer
1000 = 1000 to 1 Gear Ratio
R = Right End Gear Reducer Location
1980-104-X-DP-X-S-25-R Ametek Gemco Rotating Cam Limit Switch Model 1980-104-X-DP-X-S-25-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch
X = No Timing Dial
S= Straight Drive Gear Reducer
25 = 25 to 1 Gear Ratio
R = Right End Gear Reducer
(18LBS)
1980-104-X-SP-X-R-400-R1 Ametek Gemco Rotating Cam Limit Switch Model 1980-104-X-SP-X-R-400-R1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No shaft extension opposite gearbox / no double shaft extension
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
R= Right Angle Gear Reducer
400 = 400 to 1 Gear Ratio
R1 = Right End Gear Reducer Shaft Location 1
1980-104-X-SP-X-R-5-R1 Ametek Gemco Rotating Cam Limit Switch Model 1980-104-X-SP-X-R-5-R1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No shaft extension opposite gearbox / no double shaft extension
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
R= Right Angle Gear Reducer
5 = 5 to 1 Gear Ratio
R1 = Right End Gear Reducer Shaft Location 1
1980-104-X-SP-X-R-8-R1 Ametek Gemco Rotating Cam Limit Switch Model 1980-104-X-SP-X-R-8-R1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
4 = 4 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial
R= Right Angle Gear Reducer
8 = 8 to 1 Gear Ratio
R1 = Right End Gear Reducer Shaft Location 1
1980-104-X-SP-X-S-200-R Ametek Gemco Rotating Cam Limit Switch Model 1980-104-X-SP-X-S-200-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial
S = Straight Drive Gear Reducer
200 = 200 to 1 Gear Ratio
R = Right End Shaft Location
1980-105-L-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-105-L-SP-TD1
Series 1980
1 = NEMA 1 Enclosure
05 = 5 Independent Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw Snap Action Switches U.L. Listed
TD1 = Timing Dial Labeled for C.W. Rotation
3 Year Warranty
1980-105-L-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-105-L-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
05 = 5 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
L = Left Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(14LBS)
1980-105-R-DP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-105-R-DP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Enclosure
05 = 5 Independent Cams / Circuits / Switches
R = Right Hand Shaft Extension from enclosure
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuits. 8 screw terminals per switch
X = No Timing Dial or Dial Window is provided
3 Year Warranty
(14LBS)
1980-105-R-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-105-R-SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
05 = 5 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD1 = Timing Dial Labeled for C.W. Rotation
(14LBS)
1980-105-R-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-105-R-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
05 = 5 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(12LBS)
1980-105-X-SP-X-R-1-L7 Ametek Gemco Rotating Cam Limit Switch Model 1980-105-X-SP-X-R-1-L7
Series 1980
1 = NEMA 1 Enclosure
05 = 5 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches, Single Pole Double Throw Precision Snap Action Switches
X = No Timing Dial
R= Right Angle Gear Reducer
1 = 1 to 1 Gear Ratio
L7 = Left End Gear Reducer Shaft Location 7
1980-105-X-SP-X-S-14-R Ametek Gemco Rotating Cam Limit Switch Model 1980-105-X-SP-X-S-14-R
Series 1980
1 = NEMA 1 Enclosure
5 = 5 Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches, Single Pole Double Throw
X = No Timing Dial
S= Straight Drive Gear Reducer
14 = 14 to 1 Gear Ratio
R = Right End Shaft Location
1980-106-D-SP-TD2 Ametek Gemco Rotating Cam Limit Switch Model 1980-106-D-SP-TD2
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
06 = 6 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
D = Dual Shafts Extending from Enclosure, 2
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD2 = Timing Dial Labeled for Counter Clock Wise Rotation
3 Year Limited Warranty
(16LBS)
1980-106-D-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-106-D-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
06 = 6 Independent Cams / Circuits / Switches
D = Double Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial or Dial Window is to be provided
3 Year Warranty
(14LBS)
1980-106-L-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-106-L-SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
06 = 6 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
L = Left Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD1 = Timing Dial Labeled for C.W. Rotation
3 Year Limited Warranty
(14LBS)
1980-106-L-SP-TD2 Ametek Gemco Rotating Cam Limit Switch Model 1980-106-L-SP-TD2
Series 1980
1 = NEMA 1 Enclosure
06 = 6 Independent Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw
TD2 = Timing Dial Labeled for C.C.Wise Rotation
3 year Warranty
1980-106-L-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-106-L-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Enclosure
06 = 6 Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial or Dial Window is to be provided
3 Year Warranty
(14LBS)
1980-106-R-DP-TD2 Ametek Gemco Rotating Cam Limit Switch Model 1980-106-R-DP-TD2
Series 1980
1 = NEMA 1 Enclosure
06 = 6 Independent Cams / Circuits / Switches
R = Right Hand Shaft Extension from enclosure
DP = DPDT Switches / Double Pole Double Throw Snap Action Switches
TD2 = Timing Dial C.C.W. Counter Clock Wise Rotation
3 Year Warranty
1980-106-R-DP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-106-R-DP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
06 = 6 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(12LBS)
1980-106-R-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-106-R-SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
06 = 6 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD1 = Timing Dial Labeled for C.W. Rotation
3 Year Limited Warranty
(12LBS)
1980-106-R-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-106-R-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
06 = 6 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(14LBS)
1980-106-X-DP-X-S-2-R Ametek Gemco Rotating Cam Limit Switch Model 1980-106-X-DP-X-S-2-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Enclosure
06 = 6 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch
X = No Timing Dial
S= Straight Drive Gear Reducer
2 = 2 to 1 Gear Ratio
R = Right End Shaft Location
1980-106-X-DP-X-S-4-R Ametek Gemco Rotating Cam Limit Switch Model 1980-106-X-DP-X-S-4-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Enclosure
06 = 6 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch
X = No Timing Dial
S= Straight Drive Gear Reducer
4 = 4 to 1 Gear Ratio
R = Right End Shaft Location
1980-106-X-SP-R-X-S-28-L Ametek Gemco Rotating Cam Limit Switch Model 1980-106-X-SP-R-X-S-28-L
Series 1980
1 = NEMA 1 Rated Enclosure
6 = 6 Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
R = Rubber Boot / Seal on the Switch Plunger for additional moisture protection
X = No Timing Dial or Dial Window is to be provided
S= Straight Drive Gear Reducer
28 = 1 Gear Ratio
L = Left End Shaft Location
1980-106-X-SP-R-X-S-32-L Ametek Gemco Rotating Cam Limit Switch Model 1980-106-X-SP-R-X-S-32-L
Series 1980
1 = NEMA 1 Rated Enclosure
6 = 6 Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
R = Rubber Boot / Seal on the Switch Plunger for additional moisture protection
X = No Timing Dial or Dial Window is to be provided
S= Straight Drive Gear Reducer
32 = 1 Gear Ratio
L = Left End Shaft Location
1980-106-X-SP-X-R-10-R2 Ametek Gemco Rotating Cam Limit Switch Model 1980-106-X-SP-X-R-10-R2
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
06 = 6 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No shaft extension opposite gearbox / no double shaft extension
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
R= Right Angle Gear Reducer
10 = 10 to 1 Gear Ratio
R1 = Right End Gear Reducer Shaft Location 1
1980-106-X-SP-X-R-5-L7 Ametek Gemco Rotating Cam Limit Switch Model 1980-106-X-SP-X-R-5-L7
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
R= Right Angle Gear Reducer
5 = 5 to 1 Gear Ratio
L7 = Left End Gear Reducer Shaft Location 7
1980-106-X-SP-X-S-*-* Ametek Gemco Rotating Cam Limit Switch Model 1980-106-X-SP-X-S-*-*
Series 1980
1 = NEMA 1 Enclosure
6 = 6 Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches, Single Pole Double Throw
X = No Timing Dial
S= Straight Drive Gear Reducer
* = * Gear Ratio to be determined
* = * Shaft Location to be determined
1980-106-X-SP-X-S-200-R Ametek Gemco Rotating Cam Limit Switch Model 1980-106-X-SP-X-S-200-R
Series 1980
1 = NEMA 1 Enclosure
6 = 6 Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches, Single Pole Double Throw
X = No Timing Dial
S= Straight Drive Gear Reducer
200 = 1 Gear Ratio
R = Right End Shaft Location
1980-107-L-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-107-L-SP-X
Series 1980
1 = NEMA 1 Enclosure
7 = 7 Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw
X = No Timing Dial or Dial Window is provided
1980-107-R-DP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-107-R-DP-X
Series 1980
1 = NEMA 1 Enclosure
07 = 7 Independent Cams / Circuits / Switches
R = Right Hand Shaft Extension from enclosure
DP = DPDT Switches / Double Pole Double Throw Snap Action Switches U.L. Listed
X = No Timing Dial or Dial Window is provided
3 Year Warranty
(14LBS)
1980-107-R-SP-R-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-107-R-SP-R-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
07 = 7 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
R = Rubber Boot / Seal on the Switch Plunger for additional moisture & dust
TD1 = Timing Dial Labeled for C.W. Rotation
3 Year Limited Warranty
1980-107-R-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-107-L-SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
07 = 7 Independent Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
TD1 = Timing Dial Labeled for C.W. Rotation
1980-107-R-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-107-R-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
07 = 7 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(16LBS)
1980-107-X-SP-X-S-6-R Ametek Gemco Rotating Cam Limit Switch Model 1980-107-X-SP-X-S-6-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
07 = 7 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial
S= Straight Drive Gear Reducer
6 = 6 to 1 Gear Ratio
R = Right End Gear Reducer
(22LBS)
1980-108-D-SD-TW1 Ametek Gemco Rotating Cam Limit Switch Model 1980-108-R-SP-TW1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
8 = 8 Independent Cams / Circuits / Switches
D = Double Shaft Extension, shafts exit from both ends of the enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
TW1 = Timing Dial & Dial Window is to be provided Timing Dial Degrees Labeled for Clock Wise Rotation
3 Year Warranty
Dimensions, use a 9 to 12 circuit enclosure drawing
(22LBS)
1980-108-D-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-108-D-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
8 = 8 Independent Cams / Circuits / Switches
D = Double Shaft Extension, shafts exit from both ends of the enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial or Dial Window is to be provided
3 Year Warranty
(17LBS)
1980-108-L-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-108-L-SP-TD1
Series 1980
1 = NEMA 1 Enclosure
08 = 8 Independent Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw Snap Action Switches U.L. Listed
TD1 = Timing Dial Labeled for C.W. Rotation
3 Year Warranty
1980-108-L-SP-TD2 Ametek Gemco Rotating Cam Limit Switch Model 1980-104-L-SP-TD2
Series 1980
1 = NEMA 1 Enclosure
8 = 8 Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw
TD2 = Timing Dial C.C.W. Counter Clock Wise Rotation
1980-108-L-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-108-L-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
L = Left Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(17LBS)
1980-108-R-DP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-108-R-DP-X
Series 1980
1 = NEMA 1 Enclosure
4 = 8 Cams / Circuits / Switches
R = Right Hand Shaft Extension from enclosure
DP = DPDT Switches / Double Pole Double Throw
X = No Timing Dial or Dial Window is provided
1980-108-R-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-108-R-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
08 = 8 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(17LBS)
1980-108-X-DP-R-X-S-8-R Ametek Gemco Rotating Cam Limit Switch Model 1980-108-X-DP-R-X-S-8-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Enclosure
08 = 08 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
R = Rubber Boot on switch plunger for moisture & dust protection
X = No Timing Dial
S= Straight Drive Gear Reducer
8 = 8 to 1 Gear Ratio
R = Right End Shaft Location
(21LBS)
1980-108-X-DP-X-S-8-R Ametek Gemco Rotating Cam Limit Switch Model 1980-108-X-DP-X-S-8-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Enclosure
08 = 08 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial
S= Straight Drive Gear Reducer
8 = 8 to 1 Gear Ratio
R = Right End Shaft Location
1980-109-R-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-109-R-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
09 = 9 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(21LBS)
1980-109-X-DP-X-R-14-R1 Ametek Gemco Rotating Cam Limit Switch Model 1980-109-X-DP-X-R-14-R1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
09 = 9 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No shaft extension opposite gearbox / no double shaft extension
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuits. 8 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
R= Right Angle Gear Reducer
14 = 14 to 1 Gear Ratio
R1 = Right End Gear Reducer Shaft Location 1
1980-110-D-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-110-D-SP-TD1
Series 1980
1 = NEMA 1 Enclosure
10 = 10 Cams / Circuits / Switches
D = Double Shaft Extension (2) from enclosure
SP = SPDT Switches / Single Pole Double Throw
TD1 = Timing Dial Labeled for C.W. Rotation
(21LBS)
1980-110-R-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-110-R-SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
10 = 10 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD1 = Timing Dial Labeled for C.W. Rotation
3 Year Limited Warranty
1980-110-R-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-110-R-SP-X
Series 1980
1 = NEMA 1 Enclosure
10 = 10 Cams / Circuits / Switches
R = Right Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw
X = No Timing Dial or Dial Window is provided
(21LBS)
1980-111-R-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-111-R-SP-TD1
Series 1980
1 = NEMA 1 Enclosure
11= 11 Cams / Circuits / Switches
R = Right Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw
TD1 = Timing Dial Labeled for C.W. Rotation
1980-111-R-SP-TD2 Ametek Gemco Rotating Cam Limit Switch Model 1980-111-R-SP-TD2
Series 1980
1 = NEMA 1 Enclosure
11= 11 Cams / Circuits / Switches
R = Right Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw
TD2 = Timing Dial Labeled for C.C.W. Rotation
1980-112-R-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-112-R-SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
12 = 12 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD1 = Timing Dial Labeled for C.W. Rotation
3 Year Limited Warranty
(29LBS)
1980-112-R-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-112-R-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
12 = 12 Independent Cams / Circuits / Switches
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial or Dial Window is to be provided
3 Year Warranty
1980-112-X-SP-R-X-S-6-R Ametek Gemco Rotating Cam Limit Switch Model 1980-112-X-SP-X-S-6-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Enclosure
12 = 12 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
R = Rubber Boot / Seal on the Switch Plunger for additional moisture or dust protection
X = No Timing Dial
S= Straight Drive Gear Reducer
6 = 6 to 1 Gear Ratio
R = Right End Shaft Location
1980-112-X-SP-X-R-5-L1 Ametek Gemco Rotating Cam Limit Switch Model 1980-112-X-SP-X-R-5-L1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
12 = 12 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial is to be provided
R= right Angle Gear Reducer
5 = 5 to 1 Gear Ratio
L1 = Left End Shaft Location, Position 1
(36LBS)
1980-112-X-SP-X-S-4-R Ametek Gemco Rotating Cam Limit Switch Model 1980-112-X-SP-X-S-4-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Enclosure
12 = 12 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial
S= Straight Drive Gear Reducer
4 = 4 to 1 Gear Ratio
R = Right End Shaft Location
1980-116-R-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-116-R-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
16 = 16 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(30LBS)
1980-118-L-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-118-L-SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
018 = 18 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
L = Left Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD1 = Timing Dial Labeled for C.W. Rotation
3 Year Limited Warranty
1980-118-R-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-118-R-SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
018 = 18 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD1 = Timing Dial Labeled for C.W. Rotation
3 Year Limited Warranty
1980-118-X-SP-TD1-S-1.5-L Ametek Gemco Rotating Cam Limit Switch Model 1980-118-X-SP-TD1-S-1.5-L
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
018 = 18 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No Shaft Extension Opposite Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD1 = Timing Dial Labeled for C.W. Rotation
S = Straight Drive Gear Reducer
1.5 = 1 & 1/2 to 1 Gear Ratio
L = Gear Reducer & Shaft Extension on Left End
1980-118-X-SP-TD1-S-1.5-R Ametek Gemco Rotating Cam Limit Switch Model 1980-118-X-SP-TD1-S-1.5-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
018 = 18 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No Shaft Extension Opposite Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD1 = Timing Dial Labeled for C.W. Rotation
S = Straight Drive Gear Reducer
1.5 = 1 & 1/2 to 1 Gear Ratio
R = Gear Reducer & Shaft Extension on Right End
1980-1202-R-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-1202-R-SP-TD1
Series 1980
12 = NEMA 12 Enclosure
02 = 2 Cams / Circuits / Switches
R = Right Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw
TD1 = Timing Dial C.W. Clock Wise Rotation
1980-1203-R-SP-R-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-1203-R-SP-R-TD1
Series 1980
12 = NEMA 12 Enclosure
03= 3 Independent Cams / Circuits / Switches
R = Right Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw Snap Action Switches
R = Rubber Boot on Switch Plunger
TD1 = Timing Dial Clock Wise Rotation
1980-1203-R-SP-R-X Ametek Gemco Rotating Cam Limit Switch Model 1980-1203-R-SP-R-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Enclosure
03 = Qty. 3, Independent Cams / Circuits / Switches
R = Right Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
R = Rubber Boot / Seal on the Switch Plunger for additional moisture protection
X = No Timing Dial or Dial Window is to be provided
3 Year Warranty
1980-1203-R-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-1203-R-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Enclosure
03 = Qty. 3, Independent Cams / Circuits / Switches
R = Right Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial or Dial Window is to be provided
3 Year Warranty
1980-1204 Ametek Gemco Rotating Cam Limit Switch Model 1980-1204
Series 1980
12 = NEMA 12 Enclosure
4 = 4 Cams / Circuits / Switches
= Left Hand Shaft Extension from enclosure
= DPDT Switches / Double Pole Double Throw
X = No Timing Dial or Dial Window is provided
1980-1204-D-DP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-D-DP-X
Series 1980
12 = NEMA 12 Enclosure
4 = 4 Cams / Circuits / Switches
D = Double Shaft Extension from enclosure
DP = DPDT Switches / Double Pole Double Throw
X = No Timing Dial or Dial Window is provided
1980-1204-D-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-D-SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure
D = Dual (2) Shaft Extensions from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 TD1 = Timing Dial C.W. Clock Wise Rotation
3 Year Warranty
1980-1204-D-SPG-R-X Ametek Gemco Rotating Cam Limit Switch Model Like 1980-1204-D-SPG-R-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
D = Dual Shaft Extensions from Enclosure, 2
SPG = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch, with Gold Plated Contacts
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
R = Rubber Boots on the Switch Plunger for additional protection from Moisture & Dust
X = No Timing Dial or Dial Window is to be provided
(19LBS) 1/8
1980-1204-D-SPP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-D-SPP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
D = Double Shaft Extension from enclosure. Right & Left Side
SPP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch with Plug in Sockets
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(18LBS)
1980-1204-L-DP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-L-DP-X
Series 1980
12 = NEMA 12 Enclosure
4 = 4 Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
DP = DPDT Switches / Double Pole Double Throw
X = No Timing Dial or Dial Window is provided
1980-1204-L-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-L-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
L = Left Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(19LBS)
1980-1204-R-DP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-R-DP-X
Series 1980
12 = NEMA 12 Enclosure
4 = 4 Cams / Circuits / Switches
R = Right Hand Shaft Extension from enclosure
DP = DPDT Switches / Double Pole Double Throw
X = No Timing Dial or Dial Window is provided
1980-1204-R-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-R-SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure, Dust Tight
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD1 = Timing Dial Labeled for C.W. Rotation
3 Year Limited Warranty
1980-1204-R-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-R-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(19LBS)
1980-1204-X-DP-X-S-80-R Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-X-DP-X-S-80-R
Series 1980
12 = NEMA 12 Enclosure
4 = 4 Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
DP = DPDT Switches, Double Pole Double Throw
X = No Timing Dial
S = Straight Drive Gear Reducer
80 = 80 to 1 Gear Ratio
R = Right End Shaft Location
(24LBS)
1980-1204-X-SP-R-72-L1 Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-X-SP-R-72-L1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No Shaft Extension opposite gear box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
R = Right Angle Drive Gear Reducer
72 = 18 to 1 Gear Ratio
L1 = Shaft Location
1980-1204-X-SP-X-R-6-R1 Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-X-SP-X-R-6-R1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure, Watertight
04 = 4 Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial
R = Right Angle Drive Gear Reducer
6 = 6 to 1 Gear Ratio
R1 = Shaft Location, Right End, Shaft Position 1
1980-1204-X-SP-X-R-8-R3 Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-X-SP-X-R-8-R3
Series 1980
12 = NEMA 12 Enclosure
04 = 4 Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches, Single Pole Double Throw
X = No Timing Dial
R = Right Angle Drive Gear Reducer
8 = 8 to 1 Gear Ratio
R3 = Shaft Location
1980-1204-X-SP-X-S-2.2-L Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-X-SP-X-S-2.2-L
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial
S = Straight Drive Gear Reducer
2.2 = 2.2 to 1 Gear Ratio
L = Left End Shaft Location
1980-1204-X-SP-X-S-8-L Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-X-SP-X-S-8-L
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial
S = Straight Drive Gear Reducer
8 = 8 to 1 Gear Ratio
L = Left End Shaft Location
1980-1204-X-SP-X-S-8-R Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-X-SP-X-S-8-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial
S = Straight Drive Gear Reducer
8 = 8 to 1 Gear Ratio
R = Right End Shaft Location
1980-1205-D-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-1205-D-SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
D = Double Shaft Extension from enclosure, 2
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
TD1 = Timing Dial Labeled for Clockwise Rotation, 0-360 Degrees
3 Year Limited Warranty
(22LBS)
1980-1205-L-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-1205-L-SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
L = Left Hand Shaft Extension from enclosure, 2
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD1 = Timing Dial Labeled for C.W. Rotation
3 Year Limited Warranty
(24LBS)
1980-1205-L-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-1205-L-SP-X
Series 1980
12 = NEMA 12 Enclosure
5 = 5 Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw
X = No Timing Dial or Dial Window is provided
1980-1205-R-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-1205-R-SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
05 = 5 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from enclosure, 2
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD1 = Timing Dial Labeled for C.W. Rotation
3 Year Limited Warranty
(24LBS)
1980-1205-R-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-1205-R-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
05 = 5 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from enclosure, 2
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial
3 Year Limited Warranty
(22LBS)
1980-1205-X-DP-S-6-R Ametek Gemco Rotating Cam Limit Switch Model 1980-1205-X-DP-X-S-6-R
Series 1980
12 = NEMA 12 Enclosure
05 = 5 Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
DP = DPDT Switches, Double Pole Double Throw
X = No Timing Dial
S = Straight Drive Gear Reducer
6 = 6 to 1 Gear Ratio
R = Right End Shaft Location
1980-1206-D-DP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-D-DP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
6 = 6 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
D = Dual Shaft Extension from Enclosure
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 8 screw terminals per switch
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(16LBS)
1980-1206-L-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-L-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
06 = 6 Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial or Dial Window is to be provided
3 Year Warranty
(24LBS)
1980-1206-R-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-R-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
06 = 6 Cams / Circuits / Switches
R = Right Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial or Dial Window is to be provided
3 Year Warranty
(24LBS)
1980-1206-X-DP-R-X-S-14-R Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-X-DP-R-X-S-14-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
06 = 6 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No Shaft Extension Opposite the Gear Box
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
R = Rubber Boots on the switch plunger for additional moisture & dust protection
X = No Timing Dial
S = Straight Drive Gear Reducer
14 = 14 to 1 Gear Ratio
R = Right Side, Gear Box & Main Shaft
1980-1206-X-DP-X-R-18-L1 Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-X-DP-X-R18-L1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No Shaft Extension Opposite the Gear Box
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial
R = Right Angle Drive Gear Reducer
18 = 18 to 1 Gear Ratio
L1 = Shaft Location
1980-1206-X-DP-X-S-1.33-L Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-X-DP-X-S-1.33-L
Series 1980
12 = NEMA 12 Enclosure
6 = 6 Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
DP = DPDT Switches, Double Pole Double Throw
X = No Timing Dial
S = Straight Drive Gear Reducer
1.33 = 1.33 to 1 Gear Ratio
L = Left End Shaft Location
1980-1206-X-DP-X-S-1.33-R Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-X-DP-X-S-1.33-R
Series 1980
12 = NEMA 12 Enclosure
6 = 6 Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
DP = DPDT Switches, Double Pole Double Throw
X = No Timing Dial
S = Straight Drive Gear Reducer
1.33 = 1.33 to 1 Gear Ratio
R = Right End Shaft Location
1980-1206-X-DP-X-S36-L Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-X-DP-X-S-36-L
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
06 = 06 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial
S = Straight Drive Gear Reducer
36 = 36 to 1 Gear Ratio
L = Left End Shaft Location
1980-1206-X-SP-R-X-S-16-L Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-X-SP-R-X-S-16-L
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
06 = 6 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No shaft extension opposite gear box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
R = Rubber Boot on the switch plunger for additional moisture protection
X = No Timing Dial or Dial Window is to be provided
S= Straight Drive Gear Reducer
16 = 16 to 1 Gear Ratio
L = Left End Gear Reducer
(28LBS)
1980-1206-X-SP-TD1-S-25-R Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-X-SP-TD1-S-25-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
06 = 6 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
TD1 = Timing Dial labeled for clock wise rotation
S = Straight Drive Gear Reducer
25 = 25 to 1 Gear Ratio
R = Right End Shaft Location
1980-1206-X-SP-X-S-15-R Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-X-SP-S-15-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
06 = 6 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial
S = Straight Drive Gear Reducer
15 = 15 to 1 Gear Ratio
R = Right End Shaft Location
(26LBS)
1980-1206-X-SP-X-S-30-R Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-X-SP-X-S-30-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
06 = 6 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial
S = Straight Drive Gear Reducer
30 = 30 to 1 Gear Ratio
R = Right End Shaft Location
(26LBS)
1980-1206-X-SP-X-S-8-R Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-X-SP-X-S-8-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
06 = 6 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial
S = Straight Drive Gear Reducer
8 = 8 to 1 Gear Ratio
R = Right End Shaft Location
1980-1206-Y-SP-X-S-35-R Ametek Gemco Rotating Cam Limit Switch Model 1980-1206-Y-SP-X-S-35-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
06 = 6 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
Y = No shaft extension opposite gear box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
S= Straight Drive Gear Reducer
35 = 35 to 1 Gear Ratio
R = Right End Gear Reducer
1980-1207-D-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-1207-D-SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Enclosure
07 = 7 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure
D = Dual (2) Shaft Extensions from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD1 = Timing Dial C.W. Clock Wise Rotation
3 Year Warranty
1980-1208-D-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-1208-D-SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Enclosure
08 = 8 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure
D = Dual (2) Shaft Extensions from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD1 = Timing Dial labeled for Clock Wise Rotation
3 Year Warranty
1980-1208-D-SP-TD3 Ametek Gemco Rotating Cam Limit Switch Model 1980-1208-D-SP-TD3
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Enclosure
08 = 8 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure
D = Dual (2) Shaft Extensions from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD3 = Timing Dial labeled for Clock Wise Rotation with the main shaft vertical
3 Year Warranty
(32LBS)
1980-1208-L-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-1208-L-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
08 = 8 Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial or Dial Window is to be provided
3 Year Warranty
(26LBS)
1980-1208-R-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-1208-R-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
08 = 8 Independent Cams / Circuits / Switches
R = Right Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial or Dial Window is to be provided
3 Year Warranty
(26LBS)
1980-1208-X-SP-TD1-S-14-L Ametek Gemco Rotating Cam Limit Switch Model 1980-1208-X-SP-TD1-S-14-L
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Enclosure
08 = 08 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD1 = Timing Dial Labeled for Clockwise Rotation
S = Straight Drive Gear Reducer
14 = 14 to 1 Gear Ratio
L = Left End Shaft Location
(37LBS)
1980-1208-X-SP-X-R-18-L7 Ametek Gemco Rotating Cam Limit Switch Model 1980-1208-X-SP-X-R-18-L7
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
08 = 8 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No shaft extension opposite gearbox / no double shaft extension
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
R= Right Angle Gear Reducer
18 = 18 to 1 Gear Ratio
L7 = Left End Gear Reducer Shaft Location 7
(28LBS)
1980-1208-X-SP-X-R-25-R1 Ametek Gemco Rotating Cam Limit Switch Model 1980-1208-X-SP-X-R-25-R1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
08 = 8 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No Shaft Extension Opposite Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial is to be provided
R = Right Angle Drive Gear Reducer
25 = 25 to 1 Gear Ratio
R1 = Shaft Location
1980-1208-X-SP-X-S-30-L Ametek Gemco Rotating Cam Limit Switch Model 1980-1204-X-SP-X-S-30-L
Series 1980
12 = NEMA 12 Enclosure
08 = 08 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches, Single Pole Double Throw Snap Action
X = No Timing Dial
S = Straight Drive Gear Reducer
30 = 30 to 1 Gear Ratio
L = Left End Shaft Location
(28LBS)
1980-1209-L-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-1209-L-SP-X
Series 1980
12 = NEMA 12 Enclosure
9 = 9 Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw
X = No Timing Dial or Dial Window is provided
1980-1210-R-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-1210-R-SP-R-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
10 = 10 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
1980-1210-X-SP-R-X-R-7.5-L1 Ametek Gemco Rotating Cam Limit Switch Model 1980-1210-X-SP-R-X-R-7.5-L1
Series 1980
12 = NEMA 12 Enclosure
10 = 10 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches, Single Pole Double Throw Snap Switch U.L. Listed
R = Rubber Boot on Snap Switch Plunger
X = No Timing Dial
R = Right Angle Gear Reducer
7.5 = 7.5 to 1 Gear Ratio
L1 = Right End Shaft Location, Position 1
(34LBS)
1980-1211-L-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-1215-L-SP-TD1
Series 1980
12 = NEMA 12 Enclosure
15 = 15 Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw
TD1 = Timing Dial C.W. Clock Wise Rotation
1980-1212-D-SP-TD3 Ametek Gemco Rotating Cam Limit Switch Model 1980-1212-D-SP-TD3
Series 1980
12 = NEMA 12 Enclosure
12 = 12 Cams / Circuits / Switches
D = Double Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw
TD3 = Timing Dial, Clock Wiser Rotation, Vertical Mounting
1980-1212-D-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-1212-D-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
12 = 12 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
D = Dual Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(21LBS)
1980-1212-X-DP-X-R-5-R3 Ametek Gemco Rotating Cam Limit Switch Model 1980-1212-X-DP-X-R-5-R3
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
12 = 12 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch
X = No Timing Dial
R= Right Angle Precision Gear Reducer
5 = 5 to 1 Gear Ratio
R3 = Right End Gear Reducer Shaft Location 3
1980-1212-X-DP-X-R-6-L7 Ametek Gemco Rotating Cam Limit Switch Model 1980-1212-X-DP-X-R-6-L7
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
12 = 12 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch
X = No Timing Dial
R = Right Angle Gear Reducer
6 = 6 to 1 Gear Ratio
R = Right End Shaft Location
1980-1215-L-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-1215-L-SP-TD1
Series 1980
12 = NEMA 12 Enclosure
15 = 15 Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw
TD1 = Timing Dial C.W. Clock Wise Rotation
1980-1216-R-SP-R-X Ametek Gemco Rotating Cam Limit Switch Model 1980-1216-R-SP-R-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
16 = 16 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
R = Rubber Boot / Seal on the Switch Plunger for additional dust & moisture protection
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(50LBS)
1980-1346 Ametek Gemco Rotating Cam Limit Switch like Model 1980-104-R-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
03 = 3 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
L = Left Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
Special Engineered Product, 3 Cams with a provision for a 4th cam installed by the OEM. A switch is installed but the OEM provided their own or left out the cam in the spare area for future use
3 Year Limited Warranty
(12LBS)
1980-1535 Ametek Gemco Rotating Cam Limit Switch Model 1980-1535 like a 1980-102-L-SP-X with a special main shaft
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
02 = 2 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
L = Left Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
Specially Engineered Main Shaft Extension: 1/2 Inch Dia X 2 & 5/8 Inches Long
Perkins Press
(10LBS)
1980-1669 Ametek Gemco Deck Type Limit Switch. 3 Decks. 1950-1-B-A-AO
1980-1780 Ametek Gemco 1980-104-L-SP-X & a 1970-104 Drive-Chek
1980-1928 Ametek Gemco Rotating Cam Limit Switch
Like Model 1980-104-L-SP-X
Series 1980
1 = NEMA 1 Enclosure
4 = 4 Independent Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw
X = No Timing Dial or Dial Window is provided
Special OEM Product provided to Midland Ross in 1975
Has a special 2 & 7/16 Inch Main Shaft Extension from the Cam Box with the Shaft End Tapped for a 1/4 - 20 fastener
(12LBS)
1980-2090 Ametek Gemco Rotary Cam Limit Switch. 4 circuit, NEMA 12 Enclosure, Left Hand Shaft Extension, Qty. 3, S.P.D.T. & Qty. 1, D.P.D.T. Switches.
1980-2152 Ametek Gemco DUAL SHAFT Rotating Cam Limit Switch with Qty. 2, parallel shafts each having Qty. 3, circuits / cams / switches. Precision snap Acting D.P.D.T. Switches. Total 6 circuits. The 2 parallel shafts are coupled with a chain & sprocket inside the enclosure. A Gemco 3001-3 Adjustable Coupling is used to allow timing changes between the 2 shafts. Right hand shaft extension in position ''D'' with a second Gemco 3001-3 Adjustable Coupling. NEMA 4 Metal Enclosure. Originally designed for Kaiser Steel in 1977
1980-2179 Ametek Gemco Rotating Cam Limit Switch Like a 1980-103-L-SP-X with 2 Special Cams
Cam #1 = SD0189100 (Min. Dwell) cir #1 location LH side
Cam #2 = SD0164600 (Min. Lobe) cir #2 location
Cam #3 = SD0117800 (Standard) cir #3 location
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
03 = 3 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
L = Left Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(12LBS)
1980-2312 Ametek Gemco Specially Engineered Rotating Cam Limit Switch
Series 1980 Cam Box featuring some of the cams with Adjustable Timing & Dwell
NEMA 1 Rated Enclosure, Specially Engineered Enclosure & Cover
18 Independent Cams / Circuits / Switches
R = Right Hand Shaft Extension from Enclosure
Qty 16, SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Qty 2, DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch
13 Standard Cams, SD0117800
2 Special 15 Degree Cams, SD0203000
1 Special 75 Degree Cam, SD0203100
2 Special 40 Degree Cams, 1/2 Circuit, Right Hand, SD0207500
Internal Right Angle Gear Reducer with a having a 6:1 ratio
3 Position Selector Switch, 22mm with a Black Lever, Spring Return
9/6
1980-2366 Ametek Gemco Rotating Cam Limit Switch. 7 circuits / Cams / Switches. Single Pole Double Throw Switches. Dual Output Shafts. External Timing Dial with Pulse Disk and Switch. Includes # 3001-1 1/2 Inch Sprocket Drive Coupling.
1980-23875A Ametek Gemco Rotating Cam Limit Switch. Specially engineered product
1980-2441 Ametek Gemco Series 1980 Rotating Cam Limit Switch. 11 circuit cam box with 5 standard cams and 6 special cut cams with 20 degree lobes. SPDT switches with boots. Includes a right angle gear reducer with a 10 to 1 ratio mounted on the left end with a straight shaft in position L1 . NEMA 12 enclosures.
1980-2527 Ametek Gemco 1980 Series Cam Box
OEM Link Systems
NEMA 1 Enclosure
2 Independent Circuits / Cam / Switches
''Add a Cam'' feature which allows enclosure space for the OEM or End User to add 2 cams at a latter date
Right Hand Shaft Extension
Tach Generator Module
Precision Snap Acting Single Pole Double Trow Switches S.P.D.T.
Roller Followers were included
1980-2529 Ametek Gemco / Link Rotating Cam Limit Switch Model 1980-2529
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
4 = 4 Independent Cams / Circuits / Switches
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
With Encoder, Brevel Motors, 902436
Link Electric only
1980-2761 Ametek Gemco Rotating Cam Limit Switch
Like Switch Model 1980-911-X-SP-TD1-S-12-L
Series 1980
9 = NEMA 9 Group F Enclosure
11 = 11 Independent Cams / Circuits / Switches
X = No Shaft opposite gearbox
SP = SPDT Switches / Single Pole Double Throw Snap Action Switches U.L. Listed
TD1 = Timing Dial Labeled for C.W. Rotation
S = Straight Drive Gear Box
12 = 12 to 1 Gear Ratio
L = Gear Box Mounted to Left End
With Strip Heater & Thermostat
(50LBS)
1980-3004B Ametek Gemco Cam Limit Switch
4 Circuit with SPDT Switches
NEMA 1 with Custom Enclosure & Main Shaft Detail
Left Hand Shaft Extension
With the ''ADD A CAM'' feature for future or OEM addition of Cam / Circuit
1980-3010T Ametek Gemco Rotating Cam Limit Switch Model 1980-3010T, replaced 1980-3010
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
Left Hand Shaft Extension from Enclosure
Qty 3, SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Qty 1, DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch
Add on Tach Gen Module PSD153603 Includes Drive Chek 1970-104 & 2 Special Cams SD2231 110 Degrees & Cam SD2382 45 Degrees on the DPDT Switch 4 weeks 6/7
1980-3087 Ametek Gemco 1980 Series Cam Box with Motion Detect.
NEMA 1 Enclosure
5 Circuit / Switch / Cam
with Motion Detect
1980-3145 Ametek Gemco Special Rotating Cam Limit Switch. NEMA 1 Enclosure, 4 Cams / Circuits, Left Hand Shaft Extension, S.P.D.T. = Single Pole Double Throw Switches, 3 Standard Cams with a provision for a 4th cam installed by the OEM Bliss Salem. The switch is installed but we have no record of what type of cam Bliss Salem installed if any in the spare area. 2 weeks to ship.
1980-3146 Ametek Gemco Rotating Cam Limit Switch Model like model 1980-106-L-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Enclosure
06 = 5 Cams / Circuits / Switches, with the add a cam feature for a future circuit
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial or Dial Window is to be provided
3 Year Warranty
(14LBS) 4/7
1980-3157 Ametek Gemco Rotating Cam Limit Switch Model 1980-3157
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
SD0197700 Optical Disc
SD0194800 Motion Detect Switch in Circuit 6
(29LBS) 7/6
1980-3315 Gemco 1980 Series Cam Box
Specially engineered product
4 Circuit
NEMA 4X, 304 Stainless Steel Enclosure
1 to 3 Straight Drive Gear Multiplier, Internally Mounted
SPDT Switches with the Rubber Boot option
Enclosure is heated with a Thermostat Controlled Strip Heater
Double Shaft Extensions from enclosure
2001403 8/7
1980-3327 Ametek Gemco Rotating Cam Limit Switch Model Like model 1980-1210-X-SP-X-R-10-R1
Series 1980
12 = NEMA 12 Enclosure
10 = 10 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches, Single Pole Double Throw Snap Switch U.L. Listed
X = No Timing Dial
R = Right Angle Gear Reducer
10 = 10 to 1 Gear Ratio
R1 = Right End Shaft Location, Position 1
Special 6 Inch Diameter Cams normally used with the Series 1997 Gate Hoist Products Line
A larger enclosure is also supplied to enclose these cams 8/6
(45LBS)
1980-3383 Ametek Gemco Rotating Cam Limit Switch Model 1980-3383
Series 1980
1 = NEMA 1 Enclosure
10 = 10 Cams / Circuits / Switches
2 of these cams do not have adjustable dwell. They are machined with 25 degrees of dwell
Right Hand Shaft extension from enclosure
9 Single Pole Double Throw Switches
1 1950-1406 Slow Make - Slow Break Switch
X = No Timing Dial or Dial Window is provided
1980-3426 Ametek Gemco 1980 Series Cam Limit Switch
Engineered Part Number
6 Circuit / Cams
NEMA 4 Rated Enclosure, Watertight
SPDT UL Rated Snap Switches
Right Hand Unit
Gear Multiplier, 4 to 1 Ratio
Includes an Ametek Gemco 1/2 Inch Direct Drive Coupling. Maximum torque rating 300 lb.-in. 1/2 inch direct & sprocket drive 404 woodruff keyway & key. 50 turns of the adjusting screw will rotate coupling 360 degrees. For easily made incremental adjustment between drive shaft & cam box
1980-3434 Ametek Gemco 1980 Series Cam Box
NEMA 12 Enclosure
6 Circuits / Cams / Switches
Double Ended Shaft Extension
Pulse Generating Disc
Built in 1983 for International Harvester
1980-3486 Ametek Gemco Cam Box
Series 1980
1980-3486
6 Independent Circuit / Cam / Switch
S.P.D.T. Switches, Single Pole Double Throw Precision Snap Acting Switches
NEMA 1 Enclosure
Left Hand Shaft Extension
Add On feature for Tach Gen
Tach Generator (supplied buy others)
Lock Out Feature (accepts padlock)
1980-3503 Ametek Gemco Rotating Cam Limit Switch Model 1980-3503
Series 1980
NEMA 9 Enclosure with strip heater & thermostat
11 Cams / Circuits / Switches
Timing Dial is included
Straight Drive Gear Reducer 10 to 1 Ratio
4 to 6 weeks to ship.
1980-3510 Ametek Gemco Rotating Cam Limit Switch Model 1980-3510 Similar to 1980-1204-L-SP-X
Series 1980
12 = NEMA 12 Enclosure
04 = 4 Independent Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
Specially machined cams 2 @ 15 Degrees Dwell & 2 @ 60 Degrees Dwell
Special 1950-1413 Switches. SPDT Slow Make - Slow Break, can be wired for Normally Open or Normally Closed Circuits. 8 screw terminals. The 1950-1413 previously supplied switch is no longer available. It was a SPST switch with a normally closed contact only
X = No Timing Dial or Dial Window is provided 5/6
1980-3742 Ametek Gemco Rotating Cam Limit
Series 1980
NEMA 9 Enclosure
11 Cams / Circuits / Switches
Double Pole Double Throw Switches
Straight Drive Gear Reducer
12 to 1 Gear Ratio
With Timing Dial, Strip Heater & Thermostat
1980-3809 Ametek Gemco Cam Limit Switch
Engineered Part Number
Like 1980-409-R-SP-X with Tach Gen., Spring Return & Clutch
1980-3875A Ametek Gemco Rotating Cam Limit Switch. Specially engineered product
1980-3989 Ametek Gemco Rotating Cam Limit Switch
1 = NEMA 1 Rated Enclosure
08 = 8 Independent Cams / Circuits / Switches
X = No shaft extension opposite gearbox / no double shaft extension
Engineered product with both Single & Double Throw Switches
X = No Timing Dial or Dial Window is to be provided
R= Right Angle Gear Reducer
40 = 40 to 1 Gear Ratio
R1 = Right End Gear Reducer Position 1
1980-3990 Ametek Gemco Rotating Cam Limit Switch
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
08 = 8 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No shaft extension opposite gearbox / no double shaft extension
Engineered product with both Single & Double Throw Switches, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
R= Right Angle Gear Reducer
20= 20 to 1 Gear Ratio
L1 = Left End Gear Reducer Shaft Location 1
1980-401-R-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-401-R-SP-X
Series 1980
4 = NEMA 4 Water Resistant Enclosure
01 = 1 Cams / Circuit / Switch
R = Right Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw Snap Action Switch U.L. Listed
X = No Timing Dial or Dial Window is provided
3 Year Warranty
(19LBS)
1980-402-D-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-402-D-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
02 = 2 Independent Cams / Circuits / Switches
D = Double Shaft Extension from enclosure, 2
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(18LBS)
1980-402-X-DP-X-R-10-R1 Ametek Gemco Rotating Cam Limit Switch Model 1980-402-X-DP-X-R-10-R1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
02 = 2 Independent Cams / Circuits / Switches. The micro-adjust cams maintain accuracy / repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand. The cams have a switch setting range of 4 through 356 Degrees
X = No Shaft Extension Opposite the Gear Box
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch.Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial
R= Right Angle Gear Reducer
10 = 10 to 1 Gear Ratio
R1 = Right End Gear Reducer Shaft Location 1
1980-403-R-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-403-R-SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
03 = 3 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD1 = Timing Dial Labeled for C.W. Rotation
3 Year Limited Warranty
(20BS)
1980-403-X-DP-X-S-200-L Ametek Gemco Rotating Cam Limit Switch Model 1980-403-X-DP-X-S-200-L
Series 1980
4 = NEMA 4 Enclosure
3 = 3 Cams / Circuits / Switches
X = No shaft extension opposite gear box
DP = DPDT Switches / Double Pole Double Throw
X = No Timing Dial or Dial Window is provided
S = Straight Drive Gear Reducer
200 = 200 to 1 Gear Ratio
L = Left End Shaft Location
26 LBS Gross
1980-404 X-SP-R-X-S-60-R Ametek Gemco Rotating Cam Limit Switch Model 1980-404-X-SP-R-X-S-60-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No shaft extension opposite gearbox / no double shaft extension
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
R = R = Rubber boot on Switch Plunger for additional moisture protection
X = No Timing Dial or Dial Window is to be provided
S= Straight Drive Gear Reducer. Shaft parallel to main shaft
60 = 60 to 1 Gear Ratio
R = Right End Gear Reducer Location
(26LBS)
1980-404-D-SP-R-X Ametek Gemco Rotating Cam Limit Switch Model 1980-404-D-SP-R-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell04 = NEMA 4 Rated Enclosure
04 = 4 Cams / Circuits / Switches
D = Double / 2 Shaft Extensions from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
R = Rubber Boot on Switch Plunger for addition moisture & contaminant protection
X = No Timing Dial or Dial Window is provided
3 Year Limited Warranty
(19LBS)
1980-404-L-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-404-L-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
4 = 4 Independent Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial or Dial Window is provided
3 Year Warranty
(18LBS)
1980-404-R-DP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-404-R-DP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
4 = 4 Independent Cams / Circuits / Switches
R = Right Hand Shaft Extension from enclosure
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial or Dial Window is provided
3 Year Warranty
(18LBS)
1980-404-R-SP-R-X Ametek Gemco Rotating Cam Limit Switch Model 1980-404-R-SP-R-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell04 = NEMA 4 Rated Enclosure
4 = 4 Cams / Circuits / Switches
R = Right Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
R = Rubber Boot on Switch Plunger for addition moisture & contaminant protection
X = No Timing Dial or Dial Window is provided
(21LBS)
1980-404-R-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-404-R-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
4 = 4 Independent Cams / Circuits / Switches
R = Right Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial or Dial Window is provided
3 Year Warranty
(20LBS)
1980-404-X-SP-R-X-S-28L Ametek Gemco Rotating Cam Limit Switch Model 1980-404-X-SP-R-X-S-28-L
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No shaft extension opposite gearbox
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
S = Straight Drive Gear Reducer
28 = 28 to 1 Gear Ratio
L = Left End Gear Reducer
(24LBS)
1980-404-X-SP-R-X-S-60-R Ametek Gemco Rotating Cam Limit Switch Model 1980-404-X-SP-R-X-S-60-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No shaft extension opposite gearbox
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
S = Straight Drive Gear Reducer
60 = 60 to 1 Gear Ratio
R = Right End Gear Reducer
(24LBS)
1980-404-X-SP-X-R-15-R2 Ametek Gemco Rotating Cam Limit Switch Model 1980-404-X-SP-X-R-15-R2
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial is to be provided
R = Right Angle Gear Reducer
15 = 15 to 1 Gear Ratio
R = Right End Shaft Location
2 = Shaft Location Position 2
1980-404-X-SP-X-R-60-R2 Ametek Gemco Rotating Cam Limit Switch Model 1980-404-X-SP-X-R-60-R2
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial is to be provided
R = Right Angle Gear Reducer
60 = 60 to 1 Gear Ratio
R = Right End Shaft Location
2 = Shaft Location Position 2
1980-404-X-SP-X-S-100-L Ametek Gemco Rotating Cam Limit Switch Model 1980-404-X-SP-X-S-100-L
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
S = Straight Drive Gear Reducer
100 = 100 to 1 Gear Ratio
L = Left End Shaft Location
(29LBS)
1980-404-X-SP-X-S-35-R Ametek Gemco Rotating Cam Limit Switch Model 1980-404-X-SP-X-S-35-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
04 = 4 Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial
S = Straight Drive Gear Reducer
35 = 35 to 1 Gear Ratio
R = Right End Shaft Location
1980-405-D-DP-R-X Ametek Gemco Rotating Cam Limit Switch Model 1980-405-D-DP-R-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure, Watertight
05 = 5 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
D = Double Shaft Extension from Enclosure, shaft out both ends
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
R = Rubber Boot / Seal on the Switch Plunger for additional moisture & dust protection
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
1980-405-D-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-405-D-SP-X
Series 1980
4 = NEMA 4 Enclosure
5 = 5 Cams / Circuits / Switches
D = Double Shaft Extension
SP = SPDT Switches / Single Pole Double Throw
X = No Timing Dial or Dial Window is provided
1980-405-R-SP-R-X Ametek Gemco Rotating Cam Limit Switch Model 1980-405-R-SP-R-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure, Watertight
05 = 5 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
R = Rubber Boot / Seal on the Switch Plunger for additional moisture & dust protection
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(22LBS)
1980-405-R-SPP-R-X Ametek Gemco Rotating Cam Limit Switch Model 1980-405-R-SPP-R-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Watertight Enclosure
05 = 5 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SPP = SPDT Switches / Single Pole Double Throw with the Optional Plug-In Socket. Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
R = Rubber Boot option on Switch Plunger for additional moisture protection
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(22LBS)
1980-405-X-DP-X-S-200-L Ametek Gemco Rotating Cam Limit Switch Model 1980-405-X-DP-X-S-200-L
Series 1980
4 = NEMA 4 Enclosure
5 = 5 Cams / Circuits / Switches
X = No shaft extension opposite gear box
DP = DPDT Switches / Double Pole Double Throw
X = No Timing Dial or Dial Window is provided
S = Straight Drive Gear Reducer
200 = 200 to 1 Gear Ratio
L = Left End Shaft Location
(30LBS)
1980-405-Y-SP-X-M-6-R Ametek Gemco Rotating Cam Limit Switch Model 1980-405-Y-SP-X-M-6-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Watertight Enclosure
05 = 5 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
Y = No shaft extension oposite the gear multiplier
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
M = Gear Multiplier supplied
6 = 6 to 1 Ratio on the gear multiplier
R = Right End, Gear Multiplier located on the Right Side
3 Year Limited Warranty
(12LBS)
1980-406-D-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-406-D-SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure, Watertight
06 = 6 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
D = Dual Shafts Extending from Enclosure,Two
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD1 = Timing Dial Labeled for C.W. Rotation
3 Year Limited Warranty
(36LBS)
1980-406-L-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-406-L-SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
06 = 6 Independent Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD1 = Timing Dial Labeled for C.W. Rotation
3 Year Limited Warranty
(27LBS)
1980-406-R-3DP/3SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-406-R-3DP/3SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
06 = 6 Independent Cams / Circuits / Switches
R = Right Hand Shaft Extension from enclosure
3DP = Qty 3 DP Switches
3SP = Qty 3 SP Switches
TD1 = Timing Dial Labeled for C.W. Rotation
3 Year Limited Warranty
1980-406-R-DP-X-S-2-L Ametek Gemco Rotating Cam Limit Switch Model 1980-406-X-DP-X-S-2-L
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
06 = 6 Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch
X = No Timing Dial
S = Straight Drive Gear Reducer
2 = 2 to 1 Gear Ratio
L = Left End Gear Reducer / Shaft Location
1980-406-R-SP-R-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-406-R-SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
06 = 6 Independent Cams / Circuits / Switches
R = Right Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
R = Rubber Boot on switch plunger for moisture & dust protection
TD1 = Timing Dial Labeled for C.W. Rotation
3 Year Limited Warranty
(36LBS)
1980-406-R-SP-R-X Ametek Gemco Rotating Cam Limit Switch Model 1980-406-R-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
06 = 6 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
R = Rubber Boot option on switch plunger for additional protection from moisture & dust
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(24LBS)
1980-406-R-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-406-R-SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
06 = 6 Independent Cams / Circuits / Switches
R = Right Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD1 = Timing Dial Labeled for C.W. Rotation
3 Year Limited Warranty
(27LBS)
1980-406-R-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-406-R-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
06 = 6 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(24LBS)
1980-406-X-DP-X-M-3-R Ametek Gemco Rotating Cam Limit Switch Model 1980-406-X-DP-X-M-3-R
Series 1980 Vertex S827-6800-30
4 = NEMA 4 Enclosure
06 = 6 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
DP = DPDT Switches, Double Pole Double Throw Snap Action Switches U.L. Listed
X = No Timing Dial
M= Multiplier Drive
3 = 1 to 3 Multiplier Ratio
R = Right End Shaft Location
1980-4478
1980-406-X-DP-X-S-2-L Ametek Gemco Rotating Cam Limit Switch Model 1980-406-R-DP-X-S-2-L
Series 1980
4 = NEMA 4 Enclosure
6 = 6 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite Gear Box
DP = D.P.D.T. Switches, Double Pole Double Throw, Snap Acting
X = No Timing Dial
S= Straight drive Gear Reducer
2 = 2 to 1 Gear Ratio
L = Left End Shaft Location
1980-406-X-SP-R-X-S-20-R Ametek Gemco Rotating Cam Limit Switch Model 1980-406-X-SP-R-X-S-20-R
Series 1980
4 = NEMA 4 Enclosure
6 = 6 Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches
R = Rubber Boot Option
X = No Timing Dial
S = Straight Gear Reducer
20 = 20 to 1 Gear Ratio
R = Right Shaft Location
1980-406-X-SP-TD4-R-15-L8 Ametek Gemco Rotating Cam Limit Switch Model 1980-406-X-SP-TD4-R-15-L8
Series 1980
4 = NEMA 4 Enclosure
6 = 6 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches, Single Pole Double Throw
TD4 = Timing Dial 0 - 360 Vertical Labeling for Counter Clock Wise Rotation
R = Right Angle Gear Reducer
15 = 15 to 1 Gear Ratio
L = Left End Shaft Location
8 = Shaft Location Position 8
3 Year Warranty
1980-406-X-SP-X-R-100-R6 Ametek Gemco Rotating Cam Limit Switch Model 1980-406-X-SP-X-R-100-R6
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Watertight Enclosure
06 = 6 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No shaft extension opposite gearbox / no double shaft extension
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
R= Right Angle Gear Reducer
100 = 100 to 1 Gear Ratio
R6 = Right End Gear Reducer Shaft Location 6
1980-406-X-SP-X-R-15-R1 Ametek Gemco Rotating Cam Limit Switch Model 1980-406-X-SP-X-R-15-R1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
06 = 6 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial is to be provided
R = Right Angle Gear Reducer
15 = 15 to 1 Gear Ratio
R = Right End Shaft Location
1 = Shaft Location Position 1
1980-406-X-SP-X-R-96-L-4 Ametek Gemco Rotating Cam Limit Switch Model 1980-406-X-SP-X-R-96-L4
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
06 = 6 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial is to be provided
R = Right Angle Gear Reducer
96 = 96 to 1 Gear Ratio
L = Left End Shaft Location
1 = Shaft Location Position 4
(34LBS)
1980-406-X-SP-X-S-14-R Ametek Gemco Rotating Cam Limit Switch Model 1980-406-X-SP-X-S-14-R
Series 1980 30 LBS Gross
4 = NEMA 4 Enclosure
6 = 6 Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches, Single Pole Double Throw
X = No Timing Dial
S= Straight Drive Gear Reducer
14 = 14 to 1 Gear Ratio
R = Right End Shaft Location
1980-406-Y-SP-TD1-S-15-L Ametek Gemco Rotating Cam Limit Switch Model 1980-406-Y-SP-TD1-S-15-L
Series 1980
4 = NEMA 4 Enclosure
6 = 6 Independent Cams / Circuits / Switches
Y = Shaft Extension Opposite the Gear Box
SP = SPDT Switches, Single Pole Double Throw
TD1 = Timing Dial 0 - 360 Clock Wise
S = Straight Drive Gear Reducer
15 = 15 to 1 Gear Ratio
L = Left End Shaft Location
3 Year Warranty
(35LBS)
1980-406-Y-SP-X-S-8-R Ametek Gemco Rotating Cam Limit Switch Model 1980-406-Y-SP-X-S-8-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
06 = 6 Independent Cams / Circuits / Switches
Y = Shaft Extension Opposite the Gear Box / Double Shaft Extension
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial
S= Straight Drive Gear Reducer
8 = 8 to 1 Gear Ratio
R = Right End Shaft Location
1980-407-R-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-407-R-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
07 = 7 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(27LBS)
1980-407-X-SP-R-X-S- Ametek Gemco Rotating Cam Limit Switch Model 1980-407-X-SP-R-S-100-L
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
07 = 7 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No Shaft Extension Opposite Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
R = Rubber Boot option on Switch Plunger for additional moisture protection
X = No Timing Dial is to be provided
S = Straight Drive Gear Reducer
100 = 100 to 1 Gear Ratio
L = Left End Gear Reducer / Main Shaft
1980-407-X-SP-R-X-S-32R Ametek Gemco Rotating Cam Limit Switch Model 1980-407-X-SP-R-S-32-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
07 = 7 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No Shaft Extension Opposite Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
R = Rubber Boot option on Switch Plunger for additional moisture protection
TD2 = Timing Dial Labeled for Reverse Rotation
S = Straight Drive Gear Reducer
32 = 32 to 1 Gear Ratio
R = Right End Gear Reducer / Main Shaft
1980-408-L-SP-R-X Ametek Gemco Rotating Cam Limit Switch Model 1980-408-L-SP-R-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Watertight Enclosure
08 = 8 Independent Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
R = Rubber Boot option on switch plunger
X = No Timing Dial or Dial Window is to be provided
3 Year Warranty
(32LBS)
1980-408-L-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-408-L-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Watertight Enclosure
08 = 8 Independent Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial or Dial Window is to be provided
3 Year Warranty
(32LBS)
1980-408-R-DP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-408-R-DP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Watertight Enclosure
08 = 8 Independent Cams / Circuits / Switches
R = Right Hand Shaft Extension from enclosure
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuits. 8 screw terminals per switch
TD1 = Timing Dial Labeled for C.W. Rotation
3 Year Warranty
(32LBS)
1980-408-R-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-408-R-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Watertight Enclosure
08 = 8 Independent Cams / Circuits / Switches
R = Right Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial or Dial Window is to be provided
3 Year Warranty
(32LBS)
1980-408-X-DP-TD1-R-1-L1 Ametek Gemco Rotating Cam Limit Switch Model 1980-408-X-DP-TD1-R-1-L1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Watertight Enclosure
08 = 8 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite Gear Box
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuits. 8 screw terminals per switch
TD1 = Timing Dial Labeled for C.W. Rotation
R = Right Angle Gear Reducer
L1 = Shaft Location from Gear Box
1980-408-X-SP-TD1-X-M-3-R Ametek Gemco Rotating Cam Limit Switch Model 1980-408-X-SP-TD1-M-3-R
Series 1980
4 = NEMA 4 Enclosure
08 = 8 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches, Single Pole Double Throw
TD1 = Timing Dial Clock Wise Rotation
M= Multiplier Drive
3 = 1 to 3 Multiplier Ratio
R = Right End Shaft Location
1980-408-Y-SP-X-M-4-L Ametek Gemco Rotating Cam Limit Switch Model 1980-408-Y-SP-X-M-4-L
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
08 = 8 Independent Cams / Circuits / Switches
Y = Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial
M= Multiplier Drive
4 = 1 to 4 Multiplier Ratio
L = Left End Shaft Location
(36LBS)
1980-409-R-4DP/5SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-409-R-4DP/5SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
09 = 9 Independent Cams / Circuits / Switches
R = Right Hand Shaft Extension from enclosure
4DP = Qty 4 DP Switches
5SP = Qty 5 SP Switches
TD1 = Timing Dial Labeled for C.W. Rotation
3 Year Limited Warranty
1980-410-D-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-410-D-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
10 = 10 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
D = Double Shaft Extension from both sides Enclosure 2
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
1980-410-L-SP-R-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-410-L-SP-R-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Watertight Enclosure
10 = 10 Independent Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
R = Rubber Boot on switch plunger for moisture & dust protection
TD1 = Timing Dial Labeled for C.W. Rotation
3 Year Limited Warranty
1980-410-R-SP-R-X Ametek Gemco Rotating Cam Limit Switch Model 1980-410-R-SP-R-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
10 = 10 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
R = Rubber Boot / Seal on the Switch Plunger for additional moisture & dust protection
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
1980-410-R-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-410-R-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
10 = 10 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
1980-410-X-SP-TD1-S-80-R Ametek Gemco Rotating Cam Limit Switch Model 1980-410-X-SP-TD1-S-80-R
Series 1980
4 = NEMA 4 Enclosure
10 = 10 Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches, Single Pole Double Throw
TD1 = Timing Dial, Clockwise Rotation
S = Straight Drive Gear Reducer
80 = 80 to 1 Gear Ratio
R = Right End Shaft Location
1980-410-X-SP-TD2-S-35-L Ametek Gemco Rotating Cam Limit Switch Model 1980-410-X-SP-TD2-S-35-L
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
10 = 10 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
TD2 = Timing Dial Labeled for Counter Clock Wise Rotation
S= Straight Drive Gear Reducer
35= 35 to 1 Gear Ratio
L = Left End Shaft Location
(24LBS)
1980-410-X-SP-X-S-100-R Ametek Gemco Rotating Cam Limit Switch Model 1980-410-X-SP-X-S-100-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
10 = 10 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660 X = No Timing Dial or Dial Window is to be provided
S = Straight Drive Gear Reducer
100 = 100 to 1 Gear Ratio
R = Right End Shaft Location
1980-411-R-SP-TD2 Ametek Gemco Rotating Cam Limit Switch Model 1980-411-R-SP-TD2
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
11= 11 Independent Cams / Circuits / Switches
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 4 screw terminals per switch
TD2 = Timing Dial Labeled for C.C.W. Counter Clock Wise Rotation but without timing dial window on the enclosure
3 Year Warranty
(36LBS)
1980-411-X-SP-X-M-4-R Ametek Gemco Rotating Cam Limit Switch Model 1980-411-X-SP-X-M-4-R
Series 1980
4 = NEMA 4 Enclosure
11= 11 Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches, Single Pole Double Throw
X = No Timing Dial
M = Multiplier Drive
4 = 4 to 1 Gear Multiplier
R = Right End Shaft Location
(43LBS)
1980-411-X-SP-X-S-4-R Ametek Gemco Rotating Cam Limit Switch Model 1980-411-X-SP-X-S-4-R
Series 1980
4 = NEMA 4 Enclosure
11= 11 Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches, Single Pole Double Throw
X = No Timing Dial
S = Straight Drive Gear Reducer
4 = 4 to 1 Gear Ratio
R = Right End Shaft Location
1980-412-X-SP-X-S-100-R Ametek Gemco Rotating Cam Limit Switch Model 1980-412-X-SP-X-S-100-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
12= 12 Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial
S = Straight Drive Gear Reducer
100 = 100 to 1 Gear Ratio
R = Right End Shaft Location
41 LBS
1980-412-X-SP-X-S-36-L Ametek Gemco Rotating Cam Limit Switch Model 1980-412-X-SP-X-S-36-L
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Watertight Enclosure
12 = 12 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial
S= Straight Drive Gear Reducer
36 = 36 to 1 Gear Ratio
L = Left End Shaft Location
1980-412-X-SP-X-S10-L Ametek Gemco Rotating Cam Limit Switch Model 1980-412-X-SP-X-S-10-L
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure, Watertight
12 = 12 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial
S = Straight Drive Gear Reducer
10 = 10 to 1 Gear Ratio
L = Left End Shaft Location
1980-412-Y-SP-X-M-6-R Ametek Gemco Rotating Cam Limit Switch Model 1980-412-Y-SP-X-M-6-R
Series 1980
4 = NEMA 4 Enclosure
12 = 12 Cams / Circuits / Switches
Y = Shaft Extension oposite gearbox. (double)
SP = SPDT Switches. Single Pole Double Throw
X = No Timing Dial
M = Mutiplier Drive
6 = 1 to 6 Gear Multiplier Ratio
R = Gear Multiplier, Right End Loc
1980-412-Y-SP-X-S-200-L Ametek Gemco Rotating Cam Limit Switch Model 1980-412-Y-SP-X-S-200-L
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
12 = 12 Independent Cams / Circuits / Switches
Y = Shaft Extension Opposite the Gear Box / Double Shaft Extension
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial
S= Straight Drive Gear Reducer
200 = 200 to 1 Gear Ratio
L = Left End Gear Box & Shaft Location
1980-414-R-SP-R-TD1 Ametek Gemco Rotating Cam Limit Switch Model 980-414-R-SP-R-TD1
Series 1980
4 = NEMA 4 Rated Enclosure
14 = 14 Cams / Circuits / Switches
R = Right Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw
R = Rubber Boot on Switch Plunger
TD1 = Timing Dial C.W. Clock Wise Rotation
R = Right Hand Shaft Extension
1980-415-X-SP-TD1-S-12-R Ametek Gemco Rotating Cam Limit Switch Model 1980-415-X-SP-TD1-S-12-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
15 = 15 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD1 = Timing Dial Labeled for C.W. Rotation
S = Straight Drive Gear Reducer, shaft parallel with main shaft
12 = 12 to 1 Gear Ratio, every 12 turns of the main shaft the cams turn once
R = Right End Shaft Location
1980-416-L-SP-TD1-R-100-R1 Ametek Gemco Rotating Cam Limit Switch Model 1980-416-L-SP-TD1-R-100-R1
Series 1980
4 = NEMA 4 Enclosure
16 = 16 Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw
TD1 = Timing Dial C.W. Clock Wise Rotation
R = Right Angle Gear Reducer
100 = 100 to 1 Gear Reducer Ratio
R-1 = Shaft Location on Gear Reducer
1980-416-L-SP-TW1 Ametek Gemco Rotating Cam Limit Switch Model 1980-416-L-SP-TW1
Series 1980
4 = NEMA 4 Enclosure
16 = 16 Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw
TW1 = Timing Dial C.W. Clock Wise Rotation with a Timing Dial Window on the Enclosure
1980-416-L-SP-X Ametek Gemco Cam Limit Switch
Switch Settings 4 to 356 Degrees without a Tool - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
Series 1980 Micro-Adjust Rotating Cam Limit Switch
Model 1980-416-R-SP-X
4 = NEMA 4 Enclosure
16 = Qty. 16, Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw with one NO and one NC contact per switch rated at 15 million cycles
X = No Timing Dial or dial window is to be provided
Warranty 3 years
With NEMA 4X Stainless Adder & 2.5 Inch Shaft Extension without woodruff key and keyslot
10% expedite fee for shipment within 2.5 week. Expedite fee will be dropped if factory does not ship in 2.5 weeks
1980-4160 Ametek Gemco Cam Box like 1980R-406-X-DP-X-R-3-L with 304 Stainless Steel Option. NEMA 4X, 6 Circuits, 3 to 1 Ratio, Includes Resolver EC70289 # SD0308910. Enclosure size is to be the same as original units. Bascular Span Drawbridge Long Island NY. 1980-4160 RAGR/SS EN
1980-4161 Ametek Gemco Cam Box like1980R-406-X-DP-X-R-3-R with 304 Stainless Steel Option. NEMA 4X, 6 Circuits, 3 to 1 Ratio, Includes Resolver EC70289 # SD0308910. Enclosure size is to be the same as original units. Bascular Span Drawbridge Long Island NY. 1980-4161 RAGR/SS EN
1980-4223 Ametek Gemco Rotating Cam Limit Specially Engineered Product
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
NEMA 4 Rated Watertight Enclosure
8 Independent Cams / Circuits / Switches
Left Hand Shaft Extension from enclosure
SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Timing Dial Labeled for Counter Clock Wise Rotation
Multiplier Gear Drive with a Ratio of 1 to 4
Encoder Provision, for a customer supplied encoder
(40LBS) 7/7
1980-4245 Ametek Gemco Rotating Cam Limit Switch Model
Series 1980 Cam Box featuring cams with Adjustable Timing,Dwell & a Resolver
12 = NEMA 12 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
(19LBS) 11/7
1980-4310 Ametek Gemco Rotating Cam Limit Switch like 1980-402-R-DP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4X Rated 304 Stainless Steel Enclosure
02 = 2 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 8 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Timing Dial Window is to be provided 1/7
1980-4325 Ametek Gemco Rotating Cam Limit Switch like Model 1980-406-R-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 304 Stainless Steel Enclosure, cover, latches, bearing flanges & flange bolts. 3/4 Inch 316 Stainless Input Shaft. Meets a NEMA 4X Rating
06 = 6 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(24LBS)
1980-4375 Ametek Gemco Rotating Cam Limit Switch with Resolver Model 1980R-103-X-SP- - 64-L5
Series 1980R with AMCI Style Resolver
1 = NEMA 1 Enclosure
03 = 3 Cams / Circuits / Switches
SP = Single Pole Double Throw Switches
64 = 64 to 1 Gear Reducer
L5 = Input Shaft Location
1980-4376 Ametek Gemco Rotating Cam Limit Switch1980-12-06-L-SP
Series 1980
12 = NEMA 12 Enclosure
06 = 6 Cams / Circuits / Switches
SP = Single Pole Double Throw Switches
L = Left Hand Shaft Extension
With Pulse Generating Disc & Switch in Circuit # 8
1980-4380 Ametek Gemco Rotating Cam Limit Switch Model 1980-4380 NEMA 12 Enclosure, 6 Circuit / Cam, Right Hand Shaft Extension, SPDT Switches, with AMCI Resolver SD0495600
1980-4382 Ametek Gemco 1980 Series Rotating Cam Limit Switch. Similar to part # 1980-407-R-DP-X EXCEPT with a 316 Stainless Steel Shaft cam / main shaft along with a stainless steel drain / breather for the enclosure. NEMA 4 Enclosure, 7 Circuits / Cams, D.P.D.T. Snap Action Switches for all circuits, Right End Shaft Extension.
1980-4386 Ametek Gemco Rotating Cam Limit Switch with Resolver Model 1980-4386
Series 1980R, Standard Resolver Output Compatible with all Gemco Electronic Modules. Resolver # 04535001
4 = NEMA 4X Rated Stainless Steel Enclosure, 304 Stainless Steel enclosure option that includes:
316 SS Camshaft, 304 SS Enclosure, Cover, Latches, Bearing Flanges and Flange Bolts
8 = 8 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial or Timing Dial Window is to be provided
S = Straight Drive Extension from Gear Reducer
35 = 35 to 1 Gear Ratio
R = Right, Gear Reducer is on the Right Side of the cam box
(44LBS)
1980-4387 Ametek Gemco Rotating Cam Limit Switch Like Model 1980-404-R-SP-TD2
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Stainless Steel Enclosure
04 = 4 Cams / Circuits / Switches
R = Right Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
TD2 = Timing Dial labeled for Counter Clock Wise Rotation
Special: 304 stainless steel enclosure & 316 Stainless Steel Shaft
The enclosure is a 5-6 circuit size due to TD2 Timing dial Option
1980-4388 Ametek Gemco Rotating Cam Limit Switch Like Model 1980-404-L-SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Stainless Steel Enclosure
04 = 4 Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
TD1 = Timing Dial labeled for Clockwise Rotation
Special: 304 Stainless Steel Enclosure & 316 Stainless Steel Shaft
The enclosure size is a 5 - 6 circuit size due to the TD1 timing dial option
1980-4390 Ametek Gemco Rotating Cam Limit Switch Like Model 1980-407-R-SP-TD2
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Stainless Steel Enclosure
07 = 7 Cams / Circuits / Switches
R = Right Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
TD2 = Timing Dial Labeled for Counter Clock Wise Rotation
Special: 304 Stainless Steel Enclosure & 316 Stainless Steel Shaft
The enclosure size is a 7 - 8 circuit size
1980-4430 Ametek Gemco Rotating Cam Limit Switch. Like Model 1980-404-X-SP-X-S-28-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure with the 304 Stainless Steel Enclosure option that includes:
316 SS Camshaft, 304 SS Enclosure, Cover, Latches, Bearing Flanges and Flange Bolts
04 = 4 Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial
S = Straight Drive Gear Reducer
28 = 28 to 1 Gear Ratio
R = Right End Shaft Location
Morris Material Handling Originally
1980-4447 Ametek Gemco Rotating Cam Limit Switch Model 1980-4447
NEMA 4
7 Circuit / Cam / Switch
Double Pole Double Throw Switches
With Resolver
With Stainless Steel Drain / Breather
1980-4451 Ametek Gemco Rotating Cam Limit Switch Model Like 1980-1204-D-SPG-R-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
12 = NEMA 12 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
D = Dual Shaft Extensions from Enclosure, 2
SPG = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch, with Gold Plated Contacts
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
R = Rubber Boots on the Switch Plunger for additional protection from Moisture & Dust
X = No Timing Dial or Dial Window is to be provided
(19LBS) 1/8
1980-4455 Ametek Gemco Rotating Cam Limit Switch Model 1980-104-L-SP-TD2
Series 1980
1 = NEMA 1 Enclosure
8 = 8 Cams / Circuits / Switches
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw
TD2 = Timing Dial C.C.W. Counter Clock Wise Rotation
With 1 Special 30 Degree Cam Circuit.
1980-4469 Ametek Gemco Engineered Product.Similar to part number 1980-408-X-DP-TDI-R-1-L1 except with provisions to mount and couple a customer supplied Dynapar Encoder. Series A5840960010
304 stainless steel enclosure, cover, latches, internal camshaft, bearing flanges & flange bolts
Gear Reducer is NEMA 4, (stainless is not available)
1980-4478 Ametek Gemco Rotating Cam Limit Switch Model 1980-406-X-DP-X-M-3-R
Series 1980 Vertex S827-6800-30
4 = NEMA 4 Enclosure
6 = 6 Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
DP = DPDT Switches, Double Pole Double Throw
X = No Timing Dial
M= Multiplier Drive
3 = 1 to 3 Multiplier Ratio
R = Right End Shaft Location
1980-4478
1980-4484 Ametek Gemco Cam Limit Switch
Switch Settings 4 to 356 Degrees without a Tool - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
Series 1980 Micro-Adjust Rotating Cam Limit Switch
Model 1980-416-R-SP-X
4 = NEMA 4 Enclosure
16 = Qty. 16, Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure
L = Left Hand Shaft Extension from enclosure
SP = SPDT Switches / Single Pole Double Throw with one NO and one NC contact per switch rated at 15 million cycles
X = No Timing Dial or dial window is to be provided
Warranty 3 years
With NEMA 4X Stainless Adder & 2.5 Inch Shaft Extension without woodruff key and keyslot
1980-4500 Ametek Gemco Rotating Cam Limit Switch Model 1980-104-R-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(12LBS)
With a special main shaft diameter, keyway & length. Ametek Gemco will assign an engineered part number once the order is acknowledged by engineering. Shaft diameter as it extends from the cam box, 18mm. Shaft keyway 6X3mm, Shaft length from mounting foot center line to end 86mm
1980-4501 Ametek Gemco Rotating Cam Limit Switch Model 1980-104-L-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
L = Left Hand Shaft Extension from Enclosure
DP = DPDT Switches / Double Pole Double Throw, Snap Action, U.L. Listed. Switches can be wired to be a Normally Open or Normally Closed Circuit. 8 screw terminals per switch
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(12LBS)
With a special main shaft diameter, keyway & length. Ametek Gemco will assign an engineered part number once the order is acknowledged by engineering. Shaft diameter as it extends from the cam box, 18mm. Shaft keyway 6X3mm, Shaft length from mounting foot center line to end 86mm In error provided DPDT switches, change engr # for SPDT switches
1980-4504 Ametek Gemco Engineered Product. Same as part number 1980-4469 with the exception of the removal of the gear reducer. Mount and couple the customer supplied encoder. The encoder is to be a Dynapar Series A125-0012-1-C-320
304 Stainless Steel Enclosure, cover, latches, bearing flanges & flange bolts. 3/4 Inch 316 Stainless Input Shaft. Meets a NEMA 4X Rating 406
17 to 20 Circuit Size Enclosure Dim
Also similar to a 1980-408-L-DP-TD1
(57LBS) 40 X 14 X 7 Box
1980-4510 Ametek Gemco Rotating Cam Limit Switch Model, similar to 1980-407-X-SP-R-S-100-L
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure. 316 Stainless Steel Enclosure, cover & latches. 304 SS for Bearing Flanges & Flange Bolts. 3/4 Inch 316 Stainless Input Shaft. Meets a NEMA 4X Rating
07 = 7 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No Shaft Extension Opposite Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
R = Rubber Boot option on Switch Plunger for additional moisture protection
X = No Timing Dial is to be provided
S = Straight Drive Gear Reducer
100 = 100 to 1 Gear Ratio
L = Left End Gear Reducer / Main Shaft
(34LBS)
1980-4514 Ametek Gemco Specially Engineered Product. Similar to part number 1980-916-Y-DP-X-S-8-R with enclosure heater and thermostat
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
9 = NEMA 9 Rated Enclosure
16 = 16 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
Y = Double Shaft Extension from Enclosure, Two
DP = DPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuits. 8 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial is to be supplied
S = Straight Drive Gear Reducer
8 = 8 to 1 Gear Ratio
R- Gear Box mounted on the Right Side
(85LBS)
1980-4515 Gemco Rotating Cam Limit Switch Model like 1980-406-X-SP-X-SX-30-L
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Enclosure
06 = 6 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial
SX= Straight Drive Gear Reducer with a 1/2 Inch Diameter 316 Stainless Steel Shaft
30 = 30 to 1 Gear Ratio
L = Left End Shaft Location
1980-4522 Ametek Gemco Rotating Cam Limit Switch Model like a 1980-406-SP-R-X-TD2-R-20-L but with a 316 Stainless Steel Main Shaft
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4 = NEMA 4 Rated Watertight Enclosure
06 = 6 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
X = No Shaft Extension opposite the gearbox
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
R = Rubber Boot option on Switch Plunger for additional moisture protection
TD2 = Timing Dial Labeled for Counter Clock Wise Rotation
R - Right Angle Gear Reducer with a 316 Stainless Steel Shaft
20 = 20 to 1 Gear Ratio
L = Gear Box is located on the Left Side
(30LBS)
1980-4540 Ametek Gemco Rotating Cam Limit Switch
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
D = Double Shaft Extension from Enclosure, Two, Right & Left
GSP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch. With Gold Plated Contacts
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(12LBS) 11/7
1980-4541 Ametek Gemco Rotating Cam Limit Switch like Model 1980-104-L-GSPR-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
L = Left Hand Shaft Extension
GSPR = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch. With Gold Plated Contacts & Rubber Seals for additional dust & moisture protection
X = No Timing Dial or Dial Window is to be provided (12LBS)
1980-4542 Ametek Gemco Rotating Cam Limit Switch like Model 1980-103-L-GSPR-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
1 = NEMA 1 Rated Enclosure
03 = 3 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
L = Left Hand Shaft Extension
GSPR = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch. With Gold Plated Contacts & Rubber Seals for additional dust & moisture protection
X = No Timing Dial or Dial Window is to be provided (11LBS)
1980-4549 Ametek Gemco Rotating Cam Limit Switch Model Like 1980-4X05-R-SP-R-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
4X= NEMA 4X Rated Enclosure, Watertight, 304 Stainless Steel Option
05 = 5 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
R = Rubber Boot / Seal on the Switch Plunger for additional moisture & dust protection
X = No Timing Dial or Dial Window is to be provided
3 Year Limited Warranty
(LBS)
1980-704-X-SP-X-M-3-L Ametek Gemco Rotating Cam Limit Switch Model 1980-704-X-SP-X-M-3-L
Series 1980
7 = NEMA 7 Enclosure
04= 4 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches, Single Pole Double Throw
X = No Timing Dial
M = Multiplier Drive
3 = 3 to 1 Gear Multiplier
L = Left End Shaft Location
1980-705-R-SP-X Ametek Gemco Rotating Cam Limit Switch Model 1980-705-R-SP-X
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
7 = NEMA 7 Rated Enclosure
05 = 5 Independent Cams / Circuits / Switches
R = Right Hand Shaft Extension
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial
1980-705-X-SP-X-S-48-R Ametek Gemco Rotating Cam Limit Switch Model 1980-705-X-SP-X-S-48-R
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
7 = NEMA 7 Rated Enclosure
07 = 7 Independent Cams / Circuits / Switches
X = No Shaft Extension Opposite the Gear Box
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial
S= Straight Drive Gear Reducer
48 = 48 to 1 Gear Ratio
R = Right End Gear Reducer
1980-912-R-SP-TD1 Ametek Gemco Rotating Cam Limit Switch Model 1980-912-R-SP-TD1
Series 1980 Cam Box featuring cams with Adjustable Timing & Dwell
9 = NEMA 9 Rated Enclosure
12 = 12 Independent Cams / Circuits / Switches
The micro-adjust cams maintain an accuracy and repeatability of 1/4 degree and can be adjusted by use of a tool supplied and mounted inside the enclosure or by hand
R = Right Hand Shaft Extension from Enclosure
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
Switch Settings 4 to 356 Degrees - Gemco Manufactured Precision Snap Switches - UL Listed Assembly File E56660
TD1 = Timing Dial Labeled for C.W. Rotation
1980R-103-X-DP-R-X-5-L7 Ametek Gemco Rotating Cam Limit Switch with Resolver Model 1980R-103-X-DP-R-X-5-L7
Series 1980R, Standard Resolver Output Compatible with all Gemco Electronic Modules. Resolver # 04535001
1 = NEMA 1 Enclosure
3 = 3 Cams / Circuits / Switches
X = No Shaft Extension Opposite Gear Box
DP = Double Pole Double Throw Switches
X = No Timing Dial or Timing Dial Window is to be provided
R = Right Angle Gear Reducer
5 = 5 to 1 Gear Ratio
L7 = Left End Shaft Location, Position 7
1980R-104-L-2-SP-TD1 Ametek Gemco Rotating Cam Limit Switch with Resolver Model 1980R-104-L-2-SP-TD1
Series 1980R Cam Box featuring cams with Adjustable Timing & Dwell with Resolver Output
1 = NEMA 1 Rated Enclosure
04 = 4 Independent Cams / Circuits / Switches
L = Left Hand Shaft Extension
2 = Standard Output Compatible with AMCI resolver input devices. Resolver # 04535076
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
TD1 = Timing Dial labeled for C.W. Rotation
(20LBS)
1980R-104-L-SP-X Ametek Gemco Rotating Cam Limit Switch with Resolver Model 1980R-104-L-SP-X
Series 1980R, Standard Resolver Output Compatible with all Gemco Electronic Modules. Resolver # 04535001
1 = NEMA 1 Enclosure
04 = 4 Independent Cams / Circuits / Switches
L = Left Hand Shaft Extension
SP = Single Pole Double Throw Switches
X = No Timing Dial or Timing Dial Window is to be provided
1980R-104-R-2-SP-TD1 Ametek Gemco Rotating Cam Limit Switch with Resolver Model 1980R-104-R-2-SP-TD1
1980R= Series 1980 with Resolver Output
1 = NEMA 1 Enclosure
4 = 4 Cams / Circuits / Switches
R = Right Hand Shaft Extension
2 = Standard Output Compatible with AMCI resolver input devices. Resolver # 04535076
SP = Single Pole Double Throw Switches
TD1 = Timing Dial for C.W. Rotation
(20LBS)
1980R-1203-L-2-SP-X Ametek Gemco Rotating Cam Limit Switch with Resolver Model 1980R-104-L-2-SP-TD1
Series 1980R Cam Box featuring cams with Adjustable Timing & Dwell with Resolver Output
1 = NEMA 1 Rated Enclosure
03 = 3 Independent Cams / Circuits / Switches
L = Left Hand Shaft Extension
2 = Standard Output Compatible with AMCI resolver input devices. Resolver # 04535076
SP = SPDT Switches / Single Pole Double Throw, Snap Action, U.L. Listed Switches which can be wired for either a Normally Open or a Normally Closed Circuit. 4 screw terminals per switch
X = No Timing Dial
(20LBS)
1980R-1212-R-SP-X Ametek Gemco Rotating Cam Limit Switch with Resolver Model 1980R-1212-R-SP-X
Series 1980R, Standard Resolver Output Compatible with all Gemco Electronic Modules. Resolver # 04535001
12 = NEMA 12 Enclosure
12 = 12 Independent Cams / Circuits / Switches
R = Right Hand Shaft Extension
SP = Single Pole Double Throw Switches
X = No Timing Dial or Timing Dial Window is to be provided
1980R-416-R-DP-R-X Ametek Gemco Rotating Cam Limit Switch with Resolver Model 1980R-416-R-DP-R-X
1980R= Series 1980 with Resolver Output
4 = NEMA 4 Enclosure
16 = 16 Cams / Circuits / Switches
R = Right Hand Shaft Extension
DP = Double Pole Double Throw Switches
R = Rubber Boot on Switch Plunger Option
X = No Timing Dial
1983-1202-R-HI-A-X Ametek Gemco Optical Coupler Rotating Cam Limit Switch model 1983-1202-R-HI-A-X
Series 1983
12 = NEMA 12 Enclosure
02 = 2 Circuits / Cam / Switches
R = Right Hand Shaft Extension
HI = High Power Optical Switch with plug in socket for either AC or DC Opto 22 solid state relays
A = OAC Output with AC Output 120 Volt AC at 3 AMPS RMS
X = No Timing Dial is to be supplied
1983-1202-R-L1-X Ametek Gemco Optical Coupler Rotating Cam Limit Switch model 1983-1202-R-L1-X
Series 1983
12 = NEMA 12 Enclosure
02 = 2 Circuits / Cam / Switches
R = Right Hand Shaft Extension
L1 = Low Power Optical Switch 3 to 30 VDC with Optically Isolated Outputs 100mA Max. No output relays are provided
X = No Timing Dial is to be supplied
1983-1204-R-HI-D-X Ametek Gemco Optical Coupler Rotating Cam Limit Switch model 1983-1204-R-HI-D-X
Series 1983
12 = NEMA 12 Enclosure
04 = 4 Circuits / Cam / Switches
R = Right Hand Shaft Extension
HI = High Power Optical Switch with plug in socket for either AC or DC Opto 22 solid state relays
D = ODC Output with DC output 0 - 60 Volt DC at 3 Amps RMS
X = No Timing Dial is to be supplied
1983-1456 Ametek Gemco Optical Coupler Rotating Cam Limit Switch model 1983-1456
Series 1983
12 = NEMA 12 Enclosure
4 Low Power Optical Switches SD0310700
4 Hi Power Optical Switches SD0312400
Right Hand Shaft Extension 8/7
1986-1536 Ametek Gemco Resolver Series 1986 Same as 1986B-1-X-R-X
B = 2.25 Inch Square Flange Mount with a 3/8 Inch Diameter Input Shaft
1 = Standard Output Compatible with all Gemco Electronic Modules
X = Single Turn Resolver. No Gear Reducer
R = Standard Rear Mount Connector
X = No Options
1/7
1986-1548 Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver
A = Standard Foot Mount with a 3/4 Inch Input Shaft
1 = Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001
S = Single Turn Resolver, No gear reducer
S = Side Mount Connector
X = No other options
Enclosure NEMA 4
Max RPM 5000
Shaft Loading Axial 150 LBS Max
Shaft Loading Radial 100 LBS Max
Current # 1986A-1-X-S-X
(13LBS) 1/7
1986-1644A Ametek Gemco Engineered part number for a ''special'' or OEM Product. This is a 1980-R-104-L-SP-X with the ''Add a Cam'' feature. Add A Cam includes additional space in the enclosure for one more Circuit / Cam / Switch which the OEM or End User could use for some additional control. One of the 4 cams is 45 degrees. OEM EW Bliss 1992
1986-1669 Ametek Gemco Resolver
Series 1986 model 1986A-1GR02-S-X
A = Standard Foot Mount 3/4 Inch Input Shaft
1 = Standard Output, compatible with all Gemco Electronic Modules, Resolver # 04535001
GR02 = Single Turn Resolver with Internal Gear Reducer with a 2 to 1 Gear Ratio
S = Side Mount / Right Angle Connector
X = No exposure options
Angle Position Code 3798 Part No 79507 1/7
1986-1681 Ametek Gemco Resolver. Replaced by 1986A-1-GR300-R-X
1/7
1986-1764 Ametek Gemco Resolver. Special 2.06'' Flange Mount Resolver with side mount electrical connector & C&A Wiring (8LBS)
1986-1781A Ametek Gemco Resolver Assembly, AMCI Comp, Single Turn, was 19861781
1986-1834 Ametek Gemco
1986-1933 Ametek Gemco Resolver see 1986A-1-GR16-R-X
1/7
1986-1993 Ametek Gemco Resolver
Same as 1986A-2-GR14-R-X
1986A = Standard Foot Mount with a 3/4 Inch Diameter Input Shaft
2 = Special output compatible with AMCI resolver input devices. Resolver 04535076
GR14 = Single Turn Resolver, Internal Precision Gear Reducer with a 14 to 1 Gear Ratio
R = Standard Rear Mount Connector wired to match AMCI
X = No other options
6 Weeks to ship
1/7
1986-2004 Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver for use in limited space applications
2.06 Square Flange Mount with a 3/8 Inch Input shaft
Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001
Single Turn Resolver, No gear reducer
Side Mount Connector
No options
Enclosure NEMA 4
Maximum RPM 5000
Shaft Loading Axial 45 LBS Maximum
Shaft Loading Radial 45 LBS Maximum
2 Weeks (4LBS) Same as 1986C-X-S-X
1986-2053 Ametek Gemco Resolver. Similar to a 1986B-1-GR7-R-X with a Flat Shaft Extension
1986B = 2.25 Inch Square Flange Mount. 3/8 Inch Input Shaft
1 = Standard Output Compatible with all Gemco Electronic Modules Resolver # 04535001
GR = Single turn resolver with internal gear reducer
7 = 7 to 1 Gear Ratio
R = Standard Rear Mount Connector
X = no other options
1986-2097 Ametek Gemco 1986 Resolver. Dual Resolver Geared to 1 :1 with each Resolver Wired to a 10 Pin MS Connector
1986-XXXX Ametek Gemco Resolver. Similar to 1986I-1-X-S-X except with a 10 Pin MS Connector on the back side of the cover. An engineered part number will be assigned at time of any order
1986A-1-D1-R-X Ametek Gemco Resolver
Series 1986 model 1986A-D1-R-X
A = Standard Foot Mount 3/4 Inch Input Shaft
1 = Standard Output, compatible with all Gemco Electronic Modules, Resolver # 04535001
D1 = 64 Turn Dual Resolver. (outputs 1 & 2 only)
R = Standard Rear Mount Connector
X = No other options
1986A-1-GR03-R-E Ametek Gemco Resolver
Series 1986 model 1986A-GR03-R-E
A = Standard Foot Mount 3/4 Inch Input Shaft
1 = Standard Output, compatible with all Gemco Electronic Modules, Resolver # 04535001
GR03 = Single Turn Resolver with Internal Gear Reducer with a 3 to 1 Gear Ratio
R = Standard Rear Mount Connector
E = Stainless Steel Input Shaft and Corrosion Resistant Epoxy Coating on all exposed metal
Corrosion Resistant Epoxy Coating on all exposed metal
1986A-1-GR10-R-X Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver
A = Standard Foot Mount with a 3/4 Inch Input Shaft
1 = Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001
GR10 = Single Turn Resolver with internal gear reducer 10 to 1 Ratio
R = Standard Rear Mount Connector
X = No options
Enclosure NEMA 4
Max RPM 5000
Shaft Loading Axial 150 LBS Max
Shaft Loading Radial 100 LBS Max
1986A-1-GR16-R-X Ametek Gemco Resolver
Series 1986 model 1986A-GR16-R-X
A = Standard Foot Mount 3/4 Inch Input Shaft
1 = Standard Output, compatible with all Gemco Electronic Modules, Resolver # 04535001
GR16 = Single Turn Resolver with Internal Gear Reducer with a 16 to 1 Gear Ratio
R = Standard Rear Mount Connector
X = No exposure options
1986A-1-GR18-B60-PSA Ametek Gemco Resolver
Series 1986 model 1986A-1-GR18-B60-PSA
A = Standard Foot Mount 3/4 Inch Input Shaft
1 = Standard Output, compatible with all Gemco Electronic Modules, Resolver # 04535001
GR18 = Single Turn Resolver with Internal Gear Reducer with a 18 to 1 Gear Ratio
B60 = Side Exit Potted Pigtail with Bare Leads by 60 Foot Long
P = Additional Protective Shaft Seal for high pressure wash down environments
SA = All Stainless Steel Construction for mounting configuration ''A'' Includes Stainless Steel Mounting Foot
1986A-1-GR2-R-X Ametek Gemco Resolver. Series 1986. Standard Foot Mount 3/4 Inch Input Shaft. Standard Output, compatible with all Gemco Electronic Modules. Single Turn Resolver with internal gear reducer 2 to 1 Ratio. Standard Rear Mount Connector
1986A-1-GR20-R-X Ametek Gemco Resolver
Series 1986 model 1986A-GR20-R-X
A = Standard Foot Mount 3/4 Inch Input Shaft
1 = Standard Output, compatible with all Gemco Electronic Modules, Resolver # 04535001
GR20 = Single Turn Resolver with Internal Gear Reducer with a 20 to 1 Gear Ratio
R = Standard Rear Mount Connector
X = No exposure options
1986A-1-GR300-R-X Ametek Gemco Resolver. Replacement for resolver 1986-1681 Change made to gearing. Precision anti-backlash gears for better accuracy. Replacement is bolt in identical except for being about 1 inch shorter in length
1986A-1-GR300-R-X
Series 1986A = Standard Foot Mount, 3/4 Inch Input Shaft Dia
1 = Standard Output Compatible with all Gemco Electronic Modules
GR300 = Single Turn Resolver with internal gear reducer 300 to 1 ratio
R = Standard Rear Mount Connector
X = No other options
(10LBS)
1986A-1-GR40-R-X Ametek Gemco Resolver
Series 1986 model 1986A-GR40-R-X
A = Standard Foot Mount 3/4 Inch Input Shaft
1 = Standard Output, compatible with all Gemco Electronic Modules, Resolver # 04535001
GR40 = Single Turn Resolver with Internal Gear Reducer with a 40 to 1 Gear Ratio
R = Standard Rear Mount Connector
X = No exposure options
1986A-1-GR42-R-X Ametek Gemco Resolver
Series 1986 model 1986A-GR16-R-X
A = Standard Foot Mount 3/4 Inch Input Shaft
1 = Standard Output, compatible with all Gemco Electronic Modules, Resolver # 04535001
GR40 = Single Turn Resolver with Internal Gear Reducer with a 40 to 1 Gear Ratio
R = Standard Rear Mount Connector
X = No exposure options
1986A-1-GR58-R-X Ametek Gemco Resolver
Series 1986 model 1986A-GR58-R-X
A = Standard Foot Mount 3/4 Inch Input Shaft
1 = Standard Output, compatible with all Gemco Electronic Modules, Resolver # 04535001
GR58 = Single Turn Resolver with Internal Gear Reducer with a 58 to 1 Gear Ratio
R = Standard Rear Mount Connector
X = No exposure options
1986A-1-X-R-E Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver.
A = Standard Foot Mount with a 3/4 Inch Input Shaft
1 = Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001
X = Single Turn Resolver, No gear reducer
R = Standard Rear Mount Connector
E = Stainless Steel Input Shaft and corrosion resistant epoxy coating on all exposed metal
Enclosure NEMA 4
Max RPM 5000
Shaft Loading Axial 150 LBS Max
Shaft Loading Radial 100 LBS Max
1986A-1-X-R-X-S30R Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver
A = Standard Foot Mount with a 3/4 Inch Input Shaft
1 = Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001
X = Single Turn Resolver
R = Standard Rear Mount Connector
X = No options
Enclosure NEMA 4
SD = Straight Drive Gear Reducer
30 = 30 to 1 Gear Ratio
R = Shaft on Right Side
1986A-1-X-S-X Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver
A = Standard Foot Mount with a 3/4 Inch Input Shaft
1 = Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001
S = Single Turn Resolver, No gear reducer
S = Side Mount Connector
X = No other options
Enclosure NEMA 4
Max RPM 5000
Shaft Loading Axial 150 LBS Max
Shaft Loading Radial 100 LBS Max
Was 1986-1548
(13LBS)
1986A-2-D1-R-X Ametek Gemco Resolver
1986A = Standard Foot Mount with a 3/4 Inch Diameter Input Shaft
2 = Special output compatible with AMCI resolver input devices. Resolver 04535076
D1 = 64 Turn Dual Turn Resolver (outputs 1 and 2 only)
R = Standard Rear Mount Connector wired to match AMCI
X = No options
Enclosure NEMA 4
Max RPM 5000
Shaft Loading Axial 150 LBS Max
Shaft Loading Radial 100 LBS Max
1986A-2-GR14-R-X Ametek Gemco Resolver
1986A = Standard Foot Mount with a 3/4 Inch Diameter Input Shaft
Same as a AME-1986-1993
2 = Special output compatible with AMCI resolver input devices. Resolver 04535076
GR14 = Single Turn Resolver, Internal Precision Gear Reducer with a 14 to 1 Gear Ratio
R = Standard Rear Mount Connector wired to match AMCI
X = No other options
6 Weeks to ship
1986A-2-X-R-X Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver
A = Standard Foot Mount with a 3/4 Inch Input Shaft
2 = Special Output Compatible with AMCI Resolver Input Devices, Resolver # 04535076
X = Single Turn Resolver, No gear reducer
R = Standard Rear Mount Connector
X = No options
Enclosure NEMA 4
Max RPM 5000
Shaft Loading Axial 150 LBS Max
Shaft Loading Radial 100 LBS Max
(6LBS)
1986A-4-GR03-R-SA Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver.
A = Standard Foot Mount with a 3/4 Inch Input Shaft
4 = Special Output compatible with Modiconmotion cards. Resolver # 04535076
GR03 = Single Turn Resolver with internal gear reducer 3 to 1 ratio
R = Standard Rear Mount Connector
SA = All Stainless Steel Construction for mounting configuration ''A'' Includes Stainless Steel Mounting Foot
NEMA 4 Enclosure
Max RPM 5000
Shaft Loading Axial 150 LBS Max
Shaft Loading Radial 100 LBS Max
1986A-DN-GR09-R-X Ametek Gemco Resolver
Series 1986 model 1986A-DN-GR09-R-X
A = Standard Foot Mount 3/4 Inch Input Shaft
DN = DeviceNet Output. Resolver 04535001
GR09 = Single turn resolver with internal gear reducer 9 to 1 ratio
R = Standard Rear Mount Connector, only type available for DeviceNet
X = No other options
(7LBS)
1986A-DN-GR6-1-R-X Ametek Gemco Resolver
Series 1986 model 1986A-DN-GR6-1-R-X
A = Standard Foot Mount 3/4 Inch Input Shaft
DN = DeviceNet Output. Resolver 04535001 (rear connector only
GR06 = Single turn resolver with internal gear reducer 6 to 1 ratio
R = Standard Rear Mount Connector
X = No other options
(10LBS)
1986A-DN-X-R-X Ametek Gemco Resolver
Series 1986 model 1986A-DN-X-R-X
A = Standard Foot Mount 3/4 Inch Input Shaft
DN = DeviceNet Output. Resolver 04535001
X = Single turn resolver
R = Standard Rear Mount Connector, only type available for DeviceNet
X = No other options
(7LBS)
1986A1XRX Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver
A = Standard Foot Mount with a 3/4 Inch Input Shaft
1 = Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001
X = Single Turn Resolver, No gear reducer
R = Standard Rear Mount Connector
X = No options
Enclosure NEMA 4
Max RPM 5000
Shaft Loading Axial 150 LBS Max
Shaft Loading Radial 100 LBS Max
Same as SD0284C & SD0284200
(6LBS)
1986B-1-GR7-R-X Ametek Gemco Resolver 1986B-1-GR7-R-X
1986B = 2.25 Inch Square Flange Mount with a 3/8 Inch Input Shaft
1 = Standard Output Compatible with all Gemco Electronic Modules Resolver # 04535001
GR = Single turn resolver with internal gear reducer
7 = 7 to 1 Gear Ratio
R = Standard Rear Mount Connector
X = no other options
1986B1XRX Ametek Gemco Resolver
Series 1986
B = 2.25 Inch Square Flange Mount with a 3/8 Inch Diameter Input Shaft
1 = Standard Output Compatible with all Gemco Electronic Modules
X = Single Turn Resolver. No Gear Reducer
R = Standard Rear Mount Connector
X = No Options
1986C-1-GR20-S-S Ametek Gemco Resolver for Absolute Rotary Sensing on the most demanding applications
C = 2.06 Inch Square Flange Mount with a 3/8 Inch Diameter Input shaft
1 = Standard Output compatible with all Gemco Electronic Modules & Autotech. Gemco 04535001
GR20 = Gear Reducer with a 20 to 1 Gear Ratio
S = Side Mount Connector
S = Stainless Steel Construction. Includes Input Shaft, Bearing Housing & Can Assembly
1986C-1-X-R-P Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver
C = 2.06 Square Flange Mount with a 3/8 Inch Input shaft
1 = Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001
X = Single Turn Resolver, No gear reducer
R = Standard Rear Mount Connector
P = Additional Protective Shaft Seal for High Pressure Wash Down Applications
Enclosure NEMA 4
Maximum RPM 5000
Shaft Loading Axial 45 LBS Maximum
Shaft Loading Radial 45 LBS Maximum
(4LBS)
1986C-1-X-R-X Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver for use in limited space applications
C = 2.06 Square Flange Mount with a 3/8 Inch Input shaft
1 = Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001
X = Single Turn Resolver, No gear reducer
R = Standard Rear Mount Connector
X = No options
Enclosure NEMA 4
Maximum RPM 5000
Shaft Loading Axial 45 LBS Maximum
Shaft Loading Radial 45 LBS Maximum
2 Weeks (4LBS)
1986C-1-X-S-X Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver for use in limited space applications
C = 2.06 Square Flange Mount with a 3/8 Inch Input shaft
1 = Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001
X = Single Turn Resolver, No gear reducer
S = Side Mount Connector
X = No options
Enclosure NEMA 4
Maximum RPM 5000
Shaft Loading Axial 45 LBS Maximum
Shaft Loading Radial 45 LBS Maximum
2 Weeks (4LBS) Same as 1986-2004
1986D-1-X-R-X Ametek Gemco Inline Resolver. 2.50 Inch Face Mount. 5/8 Inch Input Shaft
1986E-1-D2-R-X Ametek Gemco Resolver 1986E-1-D2-R-X
E = 100mm Face Mount with a 5/8 Inch Diameter Input Shaft
1 = Standard Output Compatible with all Gemco Electronic Modules. Resolver part 04535001
D2 = 128 Turn Dual Resolver. Outputs 1 and 2 only
R = Standard Rear Mount Connector
X = No other options
1986F-1-X-R-X Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver.
F = 2.50 Inch Square Flange Mount with a 5/8 Inch Input Shaft
1 = Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001
X = Single Turn Resolver, No gear reducer
R = Standard Rear Mount Connector
X = No options
Enclosure NEMA 13
Max RPM 5000
Shaft Loading Axial 200 LBS Max
Shaft Loading Radial 400 LBS Max
1986F-2-X-R-X Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver
F = 2.50 Inch Square Flange Mount with a 5/8 Inch Input Shaft
2 = Special Output Compatible with AMCI Resolver Input Device, Resolver# 04535076
X = Single Turn Resolver, No gear reducer
R = Standard Rear Mount Connector
X = No options
Enclosure NEMA 13
Max RPM 5000
Shaft Loading Axial 200 LBS Max
Shaft Loading Radial 400 LBS Max
1986G-1-GR40-S-X Ametek Gemco Resolver Series 1986
G = 3 X 4 & 3/4 Inch Square Flange Mount, 5/8 Inch Input Shaft, NEMA 13
1 = Standard Output Compatible with all Gemco Electronic Modules
GR40 = Gear Reducer Ratio of 40 to 1
CE Approval
S = Side Mount Connector
X = No other options
1986G-1-GR60-S-X Ametek Gemco Resolver. Series 1986 Industrial Duty Inline Resolver
G = 3'' X 4-3/4 Inch Square Flange Mount with a 5/8 Inch Input Shaft
1 = Standard Output Compatible with all Gemco Electronic Modules, Resolver # 04535001
GR06 = Single Turn Resolver with internal gear reducer 6 to 1 Ratio
S = Side Mount Connector
X = No options
R = Standard Rear Mount Connector
X = No options
Enclosure NEMA 4
Max RPM 5000
Shaft Loading Axial 150 LBS Max
Shaft Loading Radial 100 LBS Max
1986H2D3SX Ametek Gemco Resolver. Servo Mount 1/4 Inch Diameter Input Shaft
1986MD-1-AL-1-T1 Ametek Gemco Mill Duty Resolver Housing
Series 1986 model 1986MD-1-AL-1-T1
MD = Mill Duty Housing
1 = 1/4 Inch Plate Steel Housing with plate steel bolted cover sized for single turn resolver
AL = Standard 3/4 Inch Input Shaft exiting Left End of Housing
1 = Standard 1 to 1 Gearing, between input shaft & resolver
T1 = Resolver is wired to a terminal strip inside the housing
1986XP-1-D1 Ametek Gemco Resolver
Series 1986 model 1986XP-1-D1
XP = Expolsion Proof Resolver
4.5 Inch Square Mounting
3/8 Inch Input Shaft
1 = Standard Output compatible with all Gemco electronic modules. Resolver # 04535001
D1 = 64 turn Dual Resolver (outputs 1 & 2 only)
UL Listed E10493
CSA Certified LR27991
Compliance:
NEC Class 1, Div 1, Groups C & D
Class II, Groups E, F & G
CSA Standard C22.2 No. 30
1986XP-1-GR10 Ametek Gemco Resolver
Series 1986 model 1986XP-1-GR10
XP = Expolsion Proof Resolver
4.5 Inch Square Mounting
3/8 Inch Input Shaft
1 = Standard Output compatible with all Gemco electronic modules. Resolver # 04535001
GR10 = Single Turn Resolver with Internal Gear Reducer 10 to 1 Ratio
UL Listed E10493
CSA Certified LR27991
Compliance:
NEC Class 1, Div 1, Groups C & D
Class II, Groups E, F & G
CSA Standard C22.2 No. 30
1986XP-1-GR12 Ametek Gemco Resolver
Series 1986 model 1986XP-1-GR12
XP = Explosion Proof Resolver
4.5 Inch Square Mounting
3/8 Inch Input Shaft
1 = Standard Output compatible with all Gemco electronic modules. Resolver # 04535001
GR10 = Single Turn Resolver with Internal Gear Reducer 12 to 1 Ratio
UL Listed E10493
CSA Certified LR27991
Compliance:
NEC Class 1, Div 1, Groups C & D
Class II, Groups E, F & G
CSA Standard C22.2 No. 30
1986XP-1-X Ametek Gemco Resolver
Series 1986 model 1986XP-1-X
XP = Expolsion Proof Resolver
4.5 Inch Square Mounting
3/8 Inch Input Shaft
1 = Standard Output compatible with all Gemco electronic modules. Resolver # 04535001
X = Single Turn Resolver. No Gear reducer
UL Listed E10493
CSA Certified LR27991
Compliance:
NEC Class 1, Div 1, Groups C & D
Class II, Groups E, F & G
CSA Standard C22.2 No. 30
(10LBS)
1989-1540A Ametek Gemco PLS. Series 1989 Quik-Set III Multi Turn Programmable Limit Switch. NEMA 12 Enclosure. Triac Output Module.
1989-1836 Ametek Gemco PLS Module
1989-1848 Ametek Gemco Quik-Set III CPU Module with Reset & Binary Output (6LBS)
1989-1850 Ametek Gemco 1989 Quick Set III, a special 4 Digit engineered part number would be established at the time of any order. This special system would be similar to a 1989A16R12SEA3MC12AC but will have 4 motion detectors. This system will be for a single turn resolver and offer 12 solid state programmable outputs and 4 programmable motion detectors and one fault check relay, multi-program and a 4-20mA output of position or velocity all mounted in a NEMA 12 enclosure 12/7
1989-A-16-R-12-S-C-K-X Ametek Gemco Quik-Set III Multi Turn Programmable Limit Switch
1989-A-16-R-12-S-E-K-R-X Ametek Gemco Programmable Limit Switch
16 Circuit Quik-Set III with Standard Output Package
1989-A-16-R-12-S-E-K-R-X
A = Complete System CPU and Keyboard
16 = 16 Output Circuits
R = Resolver Input
12 = 12 Bit Resolution, up to 4,096 Positions
S = Single Turn Resolver
E = Current Sinking Output. (use with Gemco output modules)
K = Standard Option Package includes: O (remote preset to reset)
U (selectable speed offset, 4 step)
M (multiprogam)
C (fault check)
R = Remote Serial Display RS422 Transmitter (requires display)
X = No Output Module Package
1989-A-16-R-14-64-E Ametek Gemco Programmable Limit Switch
16 Circuit Quik-Set III with Special Options
1989-A-16-R-14-64-E-R
A = Complete System CPU and Keyboard
16 = 16 Output Circuits
R = Resolver Input
14 = 14 Bit Resolution, up to 16,384 Positions, R Input Only
64 = 64 Turn Dual Resolver
E = Current Sinking Output (use with Gemco output modules)
1989-A-16-R-14-64-E-R Ametek Gemco Programmable Limit Switch
16 Circuit Quik-Set III with Special Options
1989-A-16-R-14-64-E-R
A = Complete System CPU and Keyboard
16 = 16 Output Circuits
R = Resolver Input
14 = 14 Bit Resolution, up to 16,384 Positions, R Input Only
64 = 64 Turn Dual Resolver
E = Current Sinking Output (use with Gemco output modules)
R = Remote Serial Display RS422 Transmitter (Display Required) any two options max.
1989-A-32-R-12-S-E-M Ametek Gemco Quik-Set II Multiturn PLS
1989-A-32-R-12-S-E-M
A = Complete system CPU and Keypad
32 = 32 Output Circuits
R = Resolver Input
12 = 12 Bit resolution / 4,096 Positions
S = Single Turn Resolver
E = Program Output Current Sinking
M = Multi-program
1989-A-48-R-12-128-E-A3-C Ametek Gemco Programmable Limit Switch. Quik-set III Multiturn
1989-A-48-R-12-128-E-A3-C
A = Complete System CPU & Keypad
48 = 40 Output Circuits. 2 Additional 16 Circuit Output Modules are required
R = Resolver Input
12 = 12 Bit Resolution / 4,096 Positions per Turn
128 = 128 Turn Resolver
E = Current Sinking, Program Output
A3 = Analog Output 4 to 20 mA, any two options maximum
C = Fault Check Relay
1989-A-48-R-12-S-E-O Ametek Gemco Quik-Set II Multiturn PLS
1989-A-48-R-12-S-E-O
A = Complete system CPU and Keypad
48 = 48 Output Circuits
R = Resolver Input
12 = 12 Bit resolution / 4,096 Positions
S = Single Turn Resolver
E = Program Output Current Sinking
O = Remote Preset to Reset
1989-CA-16-R-12-S-E-H-R Ametek Gemco Quik-Set III Multi Turn Programmable Limit Switch
AME-1989-CA-16-R-12-S-E-H-R
1989-CA-16-R-12-S-E-R Ametek Gemco Quik-Set III Multi Turn Programmable Limit Switch
AME-1989-CA-16-R-12-S-E-R
1989-CA-16-R12-S-E-H-RMO Ametek Gemco CPU Module for a 1989 Quik-Set III PLS
Part AME-1989-CA-16-R12-S-E-H-RMO
CA = CPU module Only, no Keypad
16 = 16 Output Circuits
R = Resolver Input
12 = 12 Bit Resolution, 4,096 Positions
S = Single Turn Resolver
E = Current Sinking
H = RS232 Transceiver
R = Remote Serial Display RS422 Transmitter
M = Multi-Program
O = Remote Reset to Preset
1989-CA-48-R-12-S-E-O Ametek Gemco Quik-Set II Multiturn PLS
1989-CA-48-R-12-S-E-O
CA = CPU Module Only, no Keypad
48 = 48 Output Circuits
R = Resolver Input
12 = 12 Bit resolution / 4,096 Positions
S = Single Turn Resolver
E = Program Output Current Sinking
O = Remote Preset to Reset
1989-KP Ametek Gemco Keypad Assembly for a 1989 Quik Set III 6/7
1989-O-115-A-E Ametek Gemco Output Module Assembly
115 = 115 Volt AC, 50 - 60 Hz
A = Solid State Triac, 3 AMP., 280 Volt AC Maximum
E = with Gemco Enclosure
1989-O-115-A-R-S Ametek Gemco Output Module. 16 Circuit High Power Output Module with Power Supply & 6 Foot Cable (when ordered separately)
115 = 115 Volt AC 50 - 60 Hz
A = Solid state Triac 3 AMP, 280 Volt AC Maximum
R = Reset to Preset or Brake Monitor Input
S = Standard Panel Mount
1989-O-115-M-C-S Ametek Gemco Output Module for use with 1989 Quik-Set III Multiturn PLS
1989-O-115-M-C-S
16 Circuit High Power Output Module which includes the Power Supply and a 6 Foot Connection Cable
115 = 115 Volt AC, 50 - 60 Hz. Input
M = Mechanical Relays, SPDT / Single Pole Double Throw, 10 AMP
C = Fault Check Relay Option
S = Standard Panel Mount
1989-O-115-M-S Ametek Gemco Module. 16 Circuit High Power Output Module with Power Supply with 6 Foot Cable (when ordered separately)
115 = 115 Volt AC, 50 - 60 Hz
M = Mechanical relay SPDT 10 AMP
S = Standard Panel Mount
No output module options
1990DN-PLS8-X Ametek Gemco Interface. DeviceNet Resolver Interface Module. Plugs in as a Node on a Control System or DeviceNet Scanner Card. Continues rotary position data is provided with 23-Bit Resolution. Eight built in user programmable set points allow direct control of critical functions. All programming is done over the DeviceNet Network
1992-E-R-X-X-X Ametek Gemco Press-Set Automation Controller. Press-Set System: Controller Output Module with Integral Cable Assembly
1992-E-R-X-X-X
E = Current Sinking Digital Output Code Format
R = Ram Adjust Software, hardware ordered separately
X = Controller Only
X = Controller Only, controller accepts 80 - 240 VAC 50/60 Hz, Output module must be specified with an input voltage
X = Enclosure, None / Standard
1992-E-X-16M-1-X Ametek Gemco Press-Set Automation Controller. Press-Set System: Controller Output Module with Integral Cable Assembly
1992-E-X-16M-1-X
E = Current Sinking Digital Output Code Format
X = Standard Software
16M = 16 Mechanical Relay S.P.D.T. 10 AMP, standard
1 = Input Voltage for the output module, 115 VAC 50/60 Hz. standard
X = Enclosure, None / Standard
1995-1446 Ametek Gemco Display. Remote Circular Display for the 1992 Press-Set Controller
1995-1512 Ametek Gemco Programmable Limit Switch. Micro-Set Series 1995 PLS Programmer with Brake Monitor & Lockout Security Software
1995-A-6M-P-X Ametek Gemco Micro-Set Programmable Limit Switch. Standard Micro-set PLS-Resolver Input. 1995A-6M-P-X
1995A Micro-set PLS Programmer with Reset & Motion Detect
6M = Qty. 6, Mechanical Relay SPDT 10 AMP
P = Special Software with MultiprogramSpeed Offset and Time Based Outputs to standard software features
X - Open Chassis - No Enclosure
1995-A-6M-X-12A Ametek Gemco Micro-Set Programmable Limit Switch. Standard Micro-set PLS-Resolver Input. 1995A-6M-X-12A
1995A + Micro-set PLS Programmer with Reset & Motion Detect.
6M = Qty. 6, Mechanical Relay SPDT 10 AMP
X = Standard Software
12A = NEMA 12 Enclosure. (programmer only)
1995-A-6M-X-12B-E6M Ametek Gemco Programmable Limit Switch model 1995-A-6M-X-12B-E6M
Micro-Set Series 1995 PLS Programmer with Reset to Preset & Motion Detect
A = Resolver Input only
6M = Qty. 6 Mechanical Output Relays SPDT @ 10 Amp
X =Standard Software
12B = NEMA 12 Enclosure with room for 2 Expansion Modules
E6M = Factory Mounted Expansion Module with 6 Mechanical Relays. SPDT @ 10 AMP
1995-A-6M-X-X Ametek Gemco Micro Set Programmable Limit Switch model 1995-A-6M-X-X with Reset to Preset & Motion Detect
A = Resolver Input Only
6M = 6 Mechanical Output Relays. Single Pole Double Throw, 10 AMP
X = Standard Software
X = Open Chassis - No Enclosure expansion modules ordered separately
(6LBS)
1995-B-6M-P-12A Ametek Gemco Programmable Limit Switch model 1995-B-6M-P-12A
Micro-Set Series 1995 PLS Programmer with Reset to Preset & Motion Detect
B = Resolver Input with Brake Monitor 6M = Qty. 6 Mechanical Output Relays SPDT @ 10 Amp
P = Special Software adds multiprogram speed offset & time based outputs to standard software features
12A = NEMA 12- Programmer Only
1995-B-6M-P-12B-E06M Ametek Gemco Programmable Limit Switch model 1995-B-6M-P-12B-E6M
Micro-Set Series 1995 PLS Programmer with Reset to Preset & Motion Detect
B = Resolver Input with Brake Monitor
6M = Qty. 6 Mechanical Output Relays SPDT @ 10 Amp
P = Special Software adds multiprogram speed offset & time based outputs to standard software features
12B = NEMA 12 Enclosure with room for 2 Expansion Modules
E6M = Factory Mounted Expansion Module with 6 Mechanical Relays. SPDT @ 10 AMP
1995-B-6M-P-X Ametek Gemco Programmable Limit Switch model 1995-B-6M-P-X
Micro-Set Series 1995 PLS Programmer with Reset to Preset & Motion Detect
B = Resolver Input with Brake Monitor
6M = Qty. 6 Mechanical Output Relays SPDT @ 10 Amp
P = Special Software adds multiprogram speed offset & time based outputs to standard software features
X = Open Chassis - No Enclosure. expansion modules ordered separately
(6LBS)
1995-B-6M-X-X Ametek Gemco Micro-Set Programmable Limit Switch model 1995-B-6M-X-X with Reset to Preset & Motion Detect
B = Resolver Input with Brake Monitor
6M = 6 Mechanical Relays, SPDT 10 AMP
X = Standard Software
X = Open Chassis - No Enclosure, expansion modules ordered separately
(6LBS)
1995-E-3A3D-6 Ametek Gemco Expansion Modules for the 1995 PLS.
3A3D = Output Relays, Qty 3 AC @ 1 AMP 70 - 250 Volt & Qty 3 DC @ 2 AMP 5 - 60 Volt
6 = 6 Foot Cable Length, Maximum Length 300 Feet
Maximum of 4 Output Modules per PLS
1995-E-6M-6 Ametek Gemco Output Expansion Module 1995-E-6M-6 with 6 Mechanical Relays, SPDT @ 10 AMP. Standard Cable 6 Foot long. Over 6 foot add $ 1.00 / foot and change last digit (2LBS)
1995-L-6M-P-12A Ametek Gemco Micro Set Programmable Limit Switch model 1995-L-6M-P-12A with reset to Preset & Motion Detect
L = Linear input Only
6M = Qty. 6, Mechanical Output Relays. Single Pole Double Throw, 10 AMP
P = Special Software. Adds Multiprogram Speed Offset and Time Based Outputs to the Standard Software
12A = NEMA 12 Enclosure for the programmer only
1995-L-6M-X-12A Ametek Gemco Micro Set Programmable Limit Switch model 1995-L-6M-X-12A with reset to Preset & Motion Detect
L = Linear input Only
6M = Qty. 6, Mechanical Output Relays. Single Pole Double Throw, 10 AMP
X = Standard Software
12A = NEMA 12 Enclosure for the programmer only
1995-L-6M-X-X Ametek Gemco Micro Set Programmable Limit Switch model 1995-L-6M-X-X with Reset to Preset & Motion Detect
L = Linear input Only
6M = Mechanical Output Relays. Single Pole Double Throw, 10 AMP
X = Standard Software
X = Open Chassis - No Enclosure (expansion modules ordered separately)
19951446 Ametek Gemco Display. Series 1995 Rotary Remote Display. 3/4 Inch L.E.D. Digital Display that also has an L.E.D. Bars every 10 Degrees in a Circular pattern / display. Center Digital Display can indicate either Position or RPM. Ideal for mechanical stamping presses and shears. Display can be mounted up to 1000 feet from programmer
1996C-RSA-12 Ametek Gemco Ram-Set Press Shut Height Control. Ram-Set Controller with Output Board, Standard Software and Binary Output. The Ram-Set allows you to automate the shut height adjustment process. Consistently Set Shut Height to + or - .002 Inches. Stores up to 500 Die Numbers and Shut Height Values. For use on single or double action presses
RSA = RS485 Communcation
12 = NEMA 12 Rated Enclosure
1996C-X-12 Ametek Gemco Ram-Set Press Shut Height Control. Ram-Set Controller with Output Board, Standard Software and Binary Output. The Ram-Set allows you to automate the shut height adjustment process. Consistently Set Shut Height to + or - .002 Inches. Stores up to 500 Die Numbers and Shut Height Values. For use on single or double action presses
X = No RS485 Communication
12 = NEMA 12 Rated Enclosure
1996C-X-X Ametek Gemco Ram-Set Press Shut Height Control. Ram-Set Controller with Output Board, Standard Software and Binary Output. X = no options or enclosure. The Ram-Set allows you to automate the shut height adjustment process. Consistently Set Shut Height to + or - .002 Inches. Stores up to 500 Die Numbers and Shut Height Values. For use on single or double action presses.
1997-1447 Ametek Gemco Gate Hoist Cam Box. 4 Circuit. Right End Input Shaft
1997-1448 Ametek Gemco Gate Hoist Cam Box. 4 Circuit. Left End Input Shaft
1999-Re-Calibrate Ametek Gemco Re-Calibration
1999-SEM Ametek Gemco Semelex II Safetimeter. Test Set for full and part revolution clutches. Includes Meter, Position / Velocity Transducer, Autohand and Accessories
1999OPT5YRWRNTY Ametek Gemco Optional 5 Year Limited Warranty. Includes 4 Annual Re-Calibrations. Shipping costs are not included
2000-100B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
1000 to 1 Ratio Gear Ratio, the cam block rotates once every 1000 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 12 Enclosure
Turns required to reset switch 10
Maximum switch setting @ 920
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-101B Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 4 Cam / Circuit / Switch with Single Pole Double Throw Snap Action Switches (S.P.D.T.) 5 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. 2 LBS. 6 LBS Gross
2000-102B Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Qty. 4, Independent Cams / Circuits / Switches with Single Pole Double Throw Snap Action Switches (S.P.D.T.) 10 to 1 Gear Ratio. Cast Aluminum NEMA 4 Rated Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. (6LBS)
2000-103B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Enclosure
Turns required to reset switch 1/8th
Maximum switch setting @ 19 & 1/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-104B Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 4 Cam / Circuit / Switch with Single Pole Double Throw Snap Action Switches (S.P.D.T.) 30 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. 2 LBS. 6 LBS Gross
2000-105B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
40 to 1 Ratio Gear Ratio, the cam block rotates once every 40 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Enclosure
Turns required to reset switch 1/2
Maximum switch setting @ 38 Turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-106B Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 4 Cam / Circuit / Switch with Single Pole Double Throw Snap Action Switches (S.P.D.T.) 50 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. (6 LBS)
2000-107B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
60 to 1 Ratio Gear Ratio, the cam block rotates once every 60 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Enclosure
Turns required to reset switch 1/2
Maximum switch setting @ 57 & 1/2 Turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-108B Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 4 Cam / Circuit / Switch with Single Pole Double Throw Snap Action Switches (S.P.D.T.) 80 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. 2 LBS. 6 LBS Gross
2000-109B Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 4 Cam / Circuit / Switch with Single Pole Double Throw Snap Action Switches (S.P.D.T.) 100 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. 2 LBS. 6 LBS Gross
2000-10B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Cast Aluminum Enclosure, Watertight
Turns required to reset switch 1/8
Maximum switch setting @ 18 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-110B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
250 to 1 Ratio Gear Ratio, the cam block rotates once every 250 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Cast Aluminum Enclosure, Watertight
Turns required to reset switch 2
Maximum switch setting @ 234 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-1112B Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 4 Cam / Circuit / Switch with Single Pole Double Throw Snap Action Switches (S.P.D.T.) 500 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. 2 LBS. 6 LBS Gross
2000-1113B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
150 to 1 Ratio Gear Ratio, the cam block rotates once every 150 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Cast Aluminum Enclosure, Watertight
Turns required to reset switch 4
Maximum switch setting @ 135 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-1116B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
300 to 1 Ratio Gear Ratio, the cam block rotates once every 300 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Cast Aluminum Enclosure, Watertight
Turns required to reset switch 6 & 1/2
Maximum switch setting @ 265 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-1117B Ametek Gemco Rotary Limit Switch, Worm Gear Type, 300 to 1 Ratio, 4 Cam, Single Pole Double Throw Switches, NEMA 7 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance. 2 LBS.
2000-1118B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
600 to 1 Ratio Gear Ratio, the cam block rotates once every 600 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 12 Enclosure
Turns required to reset switch 16
Maximum switch setting @ 555
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-1119B Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 4 Cam / Circuit / Switch with Single Pole Double Throw Snap Action Switches (S.P.D.T.) 600 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. (6LBS)
2000-111B Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 4 Cam / Circuit / Switch with Single Pole Double Throw Snap Action Switches (S.P.D.T.) 500 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. 2 LBS. 6 LBS Gross
2000-1122B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
2000 to 1 Ratio Gear Ratio, the cam block rotates once every 2000 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated, Cast Aluminum, Red Finish Enclosure, Watertight
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-1125B Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 4 Cam / Circuit / Switch with Single Pole Double Throw Snap Action Switches (S.P.D.T.) 4000 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 2000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
4000 to 1 Ratio Gear Ratio, the cam block rotates once every 4000 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated, Cast Aluminum, Red Finish Enclosure, Watertight
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-1128B Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 4 Cam / Circuit / Switch with Single Pole Double Throw Snap Action Switches (S.P.D.T.) 4000 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 2000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
5333.3 to 1 Ratio Gear Ratio, the cam block rotates once every 5333.3 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated, Cast Aluminum, Red Finish Enclosure, Watertight
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-112B Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 4 Cam / Circuit / Switch with Single Pole Double Throw Snap Action Switches (S.P.D.T.) 1000 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. (6LBS)
2000-1130B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
150 to 1 Ratio Gear Ratio, the cam block rotates once every 150 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 4
Maximum switch setting @ 135 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-1131B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
150 to 1 Ratio Gear Ratio, the cam block rotates once every 150 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Enclosure, Watertight
Turns required to reset switch 4
Maximum switch setting @ 135 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-1132B Ametek Gemco Rotary Limit Switch. Worm Gear Type, Two Independent Circuits / Switches / Cams. 150 to 1 Gear Ratio. UL Listed D.P.D.T. Precision Snap Action Switches. NEMA 7 & 9 Rated Die Cast Aluminum Enclosure for Hazardous Locations, designed to meet the NEC Code for Class 1, Group D, and Class 2, Groups E, F & G Locations. Maximum Speed 1000 RPM. Maximum setting at 135 Input shaft Turns. 4 Turns to Reset (6LBS)
2000-1133B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
300 to 1 Ratio Gear Ratio, the cam block rotates once every 300 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 6 & 1/2
Maximum switch setting @ 265 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-1134B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
300 to 1 Ratio Gear Ratio, the cam block rotates once every 300 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Enclosure, Watertight
Turns required to reset switch 6 & 1/2
Maximum switch setting @ 265 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-1135B Ametek Gemco Rotary Limit Switch. Worm Gear Type, Two Independent Circuits / Switches / Cams. 300 to 1 Gear Ratio. UL Listed D.P.D.T. Precision Snap Action Switches. NEMA 7 & 9 Rated Die Cast Aluminum Enclosure for Hazardous Locations, designed to meet the NEC Code for Class 1, Group D, and Class 2, Groups E, F & G Locations. Maximum Speed 1000 RPM. Maximum setting at 265 Input shaft Turns. 6 & 1/2 Turns to Reset (6LBS)
2000-1136B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
600 to 1 Ratio Gear Ratio, the cam block rotates once every 600 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 16
Maximum switch setting @ 555 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-1137B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
600 to 1 Ratio Gear Ratio, the cam block rotates once every 600 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Enclosure, Watertight
Turns required to reset switch 16
Maximum switch setting @ 555 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-1138B Ametek Gemco Rotary Limit Switch. Worm Gear Type, Two Independent Circuits / Switches / Cams. 600 to 1 Gear Ratio. UL Listed D.P.D.T. Precision Snap Action Switches. NEMA 7 & 9 Rated Die Cast Aluminum Enclosure for Hazardous Locations, designed to meet the NEC Code for Class 1, Group D, and Class 2, Groups E, F & G Locations. Maximum Speed 1000 RPM. Maximum setting at 555 Input shaft Turns. 16 Turns to Reset (6LBS)
2000-1139B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
2000 to 1 Ratio Gear Ratio, the cam block rotates once every 2000 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-1140B Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 2 Cam / Circuit / Switch with Double Pole Double Throw Snap Action Switches (D.P.D.T.) 2000 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. (6LBS)
2000-1142B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
2000 to 1 Ratio Gear Ratio, the cam block rotates once every 2000 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 29
Maximum switch setting @ 920 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-1145B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
5333.3 to 1 Ratio Gear Ratio, the cam block rotates once every 5333.3 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 29
Maximum switch setting @ 920 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-115B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 7 Rated Enclosure
Turns required to reset switch 1/8
Maximum switch setting @ 19 & 1/4 Turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
2000-116B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
40 to 1 Ratio Gear Ratio, the cam block rotates once every 40 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 7 Rated Enclosure
Turns required to reset switch 1/2
Maximum switch setting @ 38
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-118B Ametek Gemco Rotary Limit Switch, Worm Gear Type, 50 to 1 Ratio, 4 Cam, Single Pole Double Throw Switches, NEMA 7 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance. 2 LBS.
2000-11B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
30 to 1 Ratio Gear Ratio, the cam block rotates once every 30 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Cast Aluminum Enclosure, Watertight
Turns required to reset switch 1/4
Maximum switch setting @ 28 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-1205 Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
This specially engineered switch has Non Standard Cams which allow the switch contacts to be opened for 54 or 306 Degrees. Dependent on whether it is wired for normally open or closed circuits. Standard is 25 or 335 degrees. Other cam dwells are available
NEMA 12 Enclosure
Turns required to reset switch 1/8th
Maximum switch setting @ 19 & 1/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-1206 Ametek Gemco Rotary Limit Switch with an Engineered Part Number
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft
3 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537004
Non-Standard Cams S69A allow switch contacts to be opened for 90 or 270 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 1/8th
Maximum switch setting @ 19 & 1/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-121B Ametek Gemco Rotary Limit Switch, Worm Gear Type, 100 to 1 Ratio, 4 Cam, Single Pole Double Throw Switches, NEMA 7 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance. 2 LBS.
2000-122B Ametek Gemco Rotary Limit Switch, Worm Gear Type, 250 to 1 Ratio, 4 Cam, Single Pole Double Throw Switches, NEMA 7 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance. 2 LBS.
2000-1233 Ametek Gemco 1/8
2000-1234 Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Qty. 2, Standard Cams allow switch contacts to be opened for 25 or 335 Degrees
Qty. 2, Non-Standard Cams allow switch contacts to be opened for 90 or 270 Degrees
NEMA 1 & 12 Enclosure
Turns required to reset switch 1/8th
Maximum switch setting @ 19 & 1/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-1235 Ametek Gemco 2000 Series Geared Limit Switch. NEMA 1 Enclosure. 50 to 1 Gear Ratio. Single S55, 25 Degree Cam Bottom circuit. Without an electrical switch. This was manufactured for an OEM who probably modified this unit as it does not have a switch (3LBS) 1/7
2000-124B Ametek Gemco Rotary Limit Switch, Worm Gear Type, 1000 to 1 Gear Ratio, Qty. 4, Independent Circuits / Cams / Switches. Precision Snap Switches, Single Pole Double Throw S.P.D.T., NEMA 7 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance (6LBS)
2000-1256 Ametek Gemco Rotary Limit Switch, Series 2000 Worm Gear Type, 100 to 1 Ratio, 2 Cam, U.L. Listed Snap Action Switches, S.P.S.T. Single Pole Single Throw, NEMA 1 & 12 Fibralloy Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance. (2 LBS) Old Price
2000-1271 Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
40 to 1 Ratio Gear Ratio, the cam block rotates once every 40 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 1/4
Maximum switch setting @ 37 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
Like a 2000-4B has an Engineered Part Number for a Special Shaft & Bracket
(3LBS) 1/8
2000-129B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
150 to 1 Ratio Gear Ratio, the cam block rotates once every 150 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch, 4
Maximum switch setting @ 135 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(3LBS)
2000-12B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
40 to 1 Ratio Gear Ratio, the cam block rotates once every 40 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Cast Aluminum Enclosure, Watertight
Turns required to reset switch 1/4
Maximum switch setting @ 37 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-130B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
300 to 1 Ratio Gear Ratio, the cam block rotates once every 300 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch, 6 & 1/2
Maximum switch setting @ 265 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(3LBS)
2000-131B Ametek Gemco Rotary Limit Switch, Worm Gear Type, 600 to 1 Gear Ratio, Qty. 2, Circuits / Cams / switches. Precision Snap Action Switches are Single Pole Double Throw / S.P.D.T. , NEMA 12 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance (3LBS)
2000-132B Ametek Gemco Rotary Limit Switch, Worm Gear Type, 150 to 1 Ratio, 2 Cam, Single Pole Double Throw Switches, NEMA 4 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance. 2 LBS.
2000-133B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
300 to 1 Ratio Gear Ratio, the cam block rotates once every 300 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Cast Aluminum Enclosure, Watertight
Turns required to reset switch 6 & 1/2
Maximum switch setting @ 265 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-134B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
600 to 1 Ratio Gear Ratio, the cam block rotates once every 600 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Cast Aluminum Enclosure, Watertight
Turns required to reset switch 16
Maximum switch setting @ 555 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-135B Ametek Gemco Rotary Limit Switch. Worm Gear Type, Two Independent Circuits / Switches / Cams. 150 to 1 Gear Ratio. UL Listed S.P.D.T. Precision Snap Action Switches. NEMA 7 & 9 Rated Die Cast Aluminum Enclosure for Hazardous Locations, designed to meet the NEC Code for Class 1, Group D, and Class 2, Groups E, F & G Locations. Maximum Speed 1000 RPM. Maximum setting at 135 Input shaft Turns. 4 Turns to Reset (6LBS)
2000-137B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
5 to 1 Ratio Gear Ratio, the cam block rotates once every 5 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 1/8
Maximum switch setting @ 4 & 3/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-138B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
10 to 1 Ratio Gear Ratio, the cam block rotates once every 10 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 1/4
Maximum switch setting @ 9 & 1/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-139B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
40 to 1 Ratio Gear Ratio, the cam block rotates once every 40 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 3/4
Maximum switch setting @ 37 & 3/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-13B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
50 to 1 Ratio Gear Ratio, the cam block rotates once every 50 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Cast Aluminum Enclosure, Watertight
Turns required to reset switch 1/4
Maximum switch setting @ 46 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-140B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
250 to 1 Ratio Gear Ratio, the cam block rotates once every 250 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 6
Maximum switch setting @ 237 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-141B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
500 to 1 Ratio Gear Ratio, the cam block rotates once every 500 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 15 & 1/4
Maximum switch setting @ 460 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-142B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
1000 to 1 Ratio Gear Ratio, the cam block rotates once every 1000 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 29
Maximum switch setting @ 920 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-145B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
5 to 1 Ratio Gear Ratio, the cam block rotates once every 5 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Enclosure, Watertight
Turns required to reset switch 1/8
Maximum switch setting @ 4 & 3/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-146B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
10 to 1 Ratio Gear Ratio, the cam block rotates once every 10 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Enclosure, Watertight
Turns required to reset switch 1/4
Maximum switch setting @ 9 & 1/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-147B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Enclosure, Watertight
Turns required to reset switch 1/2
Maximum switch setting @ 19 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-148B Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Qty. 2, Independent Circuits / Cams / Switches. UL Listed Precision Snap Action Switches, Double Pole Double Throw / D.P.D.T. that can be wired either Normally Open or Normally Closed. 30 to 1 Gear Ratio. NEMA 4 Cast Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. Standard Dwell Cams of 25 Degrees, other dwells are available (6LBS)
2000-149B Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 2 Cam / Circuit / Switch with Double Pole Double Throw Snap Action Switches (D.P.D.T.) 40 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. 2 LBS. 6 LBS Gross
2000-14B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
60 to 1 Ratio Gear Ratio, the cam block rotates once every 60 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Cast Aluminum Enclosure, Watertight
Turns required to reset switch 1 & 1/2
Maximum switch setting @ 58 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-150B Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Standard 2 Cam / Circuit / Switch with Double Pole Double Throw Snap Action Switches (D.P.D.T.) 50 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. 2 LBS. 6 LBS Gross
2000-151B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
60 to 1 Ratio Gear Ratio, the cam block rotates once every 60 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Enclosure, Watertight
Turns required to reset switch 1 & 1/2
Maximum switch setting @ 58 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-152B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
80 to 1 Ratio Gear Ratio, the cam block rotates once every 80 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Enclosure, Watertight
Turns required to reset switch 1 & 3/4
Maximum switch setting @ 75 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-153B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
100 to 1 Ratio Gear Ratio, the cam block rotates once every 100 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Enclosure, Watertight
Turns required to reset switch 2
Maximum switch setting @ 95 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-154B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
250 to 1 Ratio Gear Ratio, the cam block rotates once every 250 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Enclosure, Watertight
Turns required to reset switch 6
Maximum switch setting @ 237 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-155B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
500 to 1 Ratio Gear Ratio, the cam block rotates once every 500 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Enclosure, Watertight
Turns required to reset switch 15 & 1/4
Maximum switch setting @ 460 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-156B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
1000 to 1 Ratio Gear Ratio, the cam block rotates once every 1000 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Enclosure, Watertight
Turns required to reset switch 29
Maximum switch setting @ 920 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-159B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
5 to 1 Ratio Gear Ratio, the cam block rotates once every 5 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet the requirements of NEC code for Class 1, Group D
Turns required to reset switch 1/8
Maximum switch setting @ 4 & 3/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-15B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
80 to 1 Ratio Gear Ratio, the cam block rotates once every 80 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Cast Aluminum Enclosure, Watertight
Turns required to reset switch 3/4
Maximum switch setting @ 77 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-160B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
10 to 1 Ratio Gear Ratio, the cam block rotates once every 10 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet the requirements of NEC code for Class 1, Group D
Turns required to reset switch 1/4
Maximum switch setting @ 9 & 1/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-161B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet the requirements of NEC code for Class 1, Group D
Turns required to reset switch 1/2
Maximum switch setting @ 19 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-162B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
40 to 1 Ratio Gear Ratio, the cam block rotates once every 40 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet the requirements of NEC code for Class 1, Group D
Turns required to reset switch 3/4
Maximum switch setting @ 37 & 3/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-163B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
50 to 1 Ratio Gear Ratio, the cam block rotates once every 50 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet the requirements of NEC code for Class 1, Group D
Turns required to reset switch 3/4
Maximum switch setting @ 46 & 3/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-164B Ametek Gemco Rotary Limit Switch. Worm Gear Type, Two Independent Circuits / Switches / Cams. 80 to 1 Gear Ratio. UL Listed D.P.D.T. Precision Snap Action Switches. NEMA 7 & 9 Rated Die Cast Aluminum Enclosure for Hazardous Locations, designed to meet the NEC Code for Class 1, Group D, and Class 2, Groups E, F & G Locations. Maximum Speed 1000 RPM. Maximum setting at 75 Input shaft Turns. 1 & 3/4 Turns to Reset (6LBS)
2000-167B Ametek Gemco Rotary Limit Switch. Worm Gear Type, Two Independent Circuits / Switches / Cams. 250 to 1 Gear Ratio. UL Listed D.P.D.T. Precision Snap Action Switches. NEMA 7 & 9 Rated Die Cast Aluminum Enclosure for Hazardous Locations, designed to meet the NEC Code for Class 1, Group D, and Class 2, Groups E, F & G Locations. Maximum Speed 1000 RPM. Maximum setting at 237 Input shaft Turns. 6 Turns to Reset (6LBS)
2000-168B Ametek Gemco Rotary Limit Switch. Worm Gear Type, Two Independent Circuits / Switches / Cams. 500 to 1 Gear Ratio. UL Listed D.P.D.T. Precision Snap Action Switches. NEMA 7 & 9 Rated Die Cast Aluminum Enclosure for Hazardous Locations, designed to meet the NEC Code for Class 1, Group D, and Class 2, Groups E, F & G Locations. Maximum Speed 1000 RPM. Maximum setting at 460 Input shaft Turns. 15 & 1/4 Turns to Reset (6LBS)
2000-169B Ametek Gemco Rotary Limit Switch. Worm Gear Type, Two Independent Circuits / Switches / Cams. 1000 to 1 Gear Ratio. UL Listed D.P.D.T. Precision Snap Action Switches. NEMA 7 & 9 Rated Die Cast Aluminum Enclosure for Hazardous Locations, designed to meet the NEC Code for Class 1, Group D, and Class 2, Groups E, F & G Locations. Maximum Speed 1000 RPM. Maximum setting at 920 Input shaft Turns. 29 Turns to Reset (6LBS)
2000-16B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
100 to 1 Ratio Gear Ratio, the cam block rotates once every 100 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Cast Aluminum Enclosure, Watertight
Turns required to reset switch 3/4
Maximum switch setting @ 94 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-171B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
150 to 1 Ratio Gear Ratio, the cam block rotates once every 150 turns of the main shaft
3 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Cast Aluminum Enclosure, Watertight
Turns required to reset switch 4
Maximum switch setting @ 135 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(5LBS)
2000-174B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
5 to 1 Ratio Gear Ratio, the cam block rotates once every 5 turns of the main shaft
3 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537004
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 1/16th
Maximum switch setting @ 4 & 3/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-175B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
10 to 1 Ratio Gear Ratio, the cam block rotates once every 10 turns of the main shaft
3 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537004
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 1/16th
Maximum switch setting @ 9 & 1/2 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-176B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft
3 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537004
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 1/8th
Maximum switch setting @ 19 & 1/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-177B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
30 to 1 Ratio Gear Ratio, the cam block rotates once every 30 turns of the main shaft
3 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537004
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 1/4
Maximum switch setting @ 28 & 1/2 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-17B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
5 to 1 Ratio Gear Ratio, the cam block rotates once every 5 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 12 Rated Enclosure
Turns required to reset switch 1/16th
Maximum switch setting @ 4 & 1/2 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-180B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
60 to 1 Ratio Gear Ratio, the cam block rotates once every 60 turns of the main shaft
3 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 1/2
Maximum switch setting @ 57 & 1/2 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-181B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
80 to 1 Ratio Gear Ratio, the cam block rotates once every 80 turns of the main shaft
3 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 1/2
Maximum switch setting @ 76 & 3/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-182B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
100 to 1 Ratio Gear Ratio, the cam block rotates once every 100 turns of the main shaft
3 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 1 & 1/2
Maximum switch setting @ 96 & 1/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-183B Ametek Gemco Rotary Limit Switch, Worm Gear Type, 250 to 1 Ratio, 3 Cam, Single Pole Double Throw Switches, NEMA 12 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance (3LBS)
2000-185B Ametek Gemco Rotary Limit Switch, Worm Gear Type, 1000 to 1 Ratio, 3 Cam, Single Pole Double Throw Switches, NEMA 1 & 12 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance. 3 LBS Gross
2000-1872 Ametek Gemco Rotary Limit Switch
Like 2000-818 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
4, Special Cams with 54 Degrees of Dwell
4 Independent Circuits / Cams / Switches
S.P.D.T. Snap Action U.L. Listed Switches # 04537004
Basic Switch Data see Table 2 Symbol C on Page 13
NEMA 12 Rated Die Cast Enclosure with Fibralloy Cover
2 to 1 Input Shaft Ratio, Every Two Turns of the Main Shaft the Cam Block Rotates Once
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from the Enclosure
Includes Woodruff Keyway & a #404 Woodruff Key
3/4 -14 N.P.T. Electrical Entrance
(4LBS) 1/8
2000-1899 Ametek Gemco Rotary Limit Switch. Spur Gear Type. 3 Circuits / Cams / Switches. S.P.D.T. Switches with a NEMA 1 Enclosure. Special 54 degree Cams.
2000-189B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
10 to 1 Ratio Gear Ratio, the cam block rotates once every 10 turns of the main shaft
3 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537004
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Enclosure, Watertight
Turns required to reset switch 1/16th
Maximum switch setting @ 9 & 1/2 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-18B Ametek Gemco Rotary Limit Switch. Worm Gear Type, Two Independent Circuits / Switches / Cams. 20 to 1 Gear Ratio. UL Listed S.P.D.T. Precision Snap Action Switches. NEMA 7 & 9 Rated Die Cast Aluminum Enclosure for Hazardous Locations, designed to meet the NEC Code for Class 1, Group D, and Class 2, Groups E, F & G Locations. Maximum Speed 1000 RPM. Maximum setting at 18 Input shaft Turns. 1/8 Turn to Reset (6LBS)
2000-190B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft
3 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537004
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Enclosure, Watertight
Turns required to reset switch 1/8th
Maximum switch setting @ 19 & 1/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-191B Ametek Gemco Rotary Limit Switch, Worm Gear Type, 30 to 1 Ratio, 3 Cam, Single Pole Double Throw Switches, NEMA 4 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance.
2000-194B Ametek Gemco Rotary Limit Switch, Worm Gear Type, 60 to 1 Ratio, 3 Cam, Single Pole Double Throw Switches - 04537004,, NEMA 4 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance
2000-195B Ametek Gemco Rotary Limit Switch, Worm Gear Type, 80 to 1 Ratio, 3 Cam, Single Pole Double Throw Switches - 04537004,, NEMA 4 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance
2000-196B Ametek Gemco Rotary Limit Switch, Worm Gear Type, 100 to 1 Ratio, 3 Cam, Single Pole Double Throw Switches - 04537004, NEMA 4 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance
2000-197B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
250 to 1 Ratio Gear Ratio, the cam block rotates once every 250 turns of the main shaft
3 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Cast Aluminum Enclosure, Watertight
Turns required to reset switch 2
Maximum switch setting @ 234 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(5LBS)
2000-198B Ametek Gemco Rotary Limit Switch, Worm Gear Type, 500 to 1 Ratio, 3 Cam, Single Pole Double Throw Switches, NEMA 4 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance
2000-199B Ametek Gemco Rotary Limit Switch, Worm Gear Type, 1000 to 1 Ratio, 3 Cam, Single Pole Double Throw Switches, NEMA 4 Rated Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance (4LBS)
2000-19B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
30 to 1 Ratio Gear Ratio, the cam block rotates once every 30 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet the requirements of NEC code for Class 1, Group D
Turns required to reset switch 1/4
Maximum switch setting @ 28 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-1B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
5 to 1 Ratio Gear Ratio, the cam block rotates once every 5 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 12 Rated Enclosure
Turns required to reset switch 1/16th
Maximum switch setting @ 4 & 1/2 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(3LBS)
2000-2003 Ametek Gemco Rotary Limit Switch. Heavy Duty Geared Rotary Limit Switch for demanding applications which require trouble free performance. 2 Independent Circuits / Cams / Switches. Precision Snap Acting (SPDT) Single Throw Double Pole Switches. 15 to 1 Gear Ratio. NEMA 12 Enclosure. Maximum speed 1800 RPM, Clock Wise or CCW Rotation. Steel & Bronze Gears. Designed to withstand Rapid Starting, Stopping, Shock & Vibration (8LBS)
2000-2004 Ametek Gemco Rotary Limit Switch. Heavy Duty Geared Rotary Limit Switch for demanding applications which require trouble free performance. 2 Independent Circuits / Cams / Switches. Precision Snap Acting (SPDT) Single Throw Double Pole Switches. 20 to 1 Gear Ratio. NEMA 12 Enclosure. Maximum speed 1800 RPM, Clock Wise or CCW Rotation. Steel & Bronze Gears. Designed to withstand Rapid Starting, Stopping, Shock & Vibration (8LBS)
2000-2005 Ametek Gemco Rotary Limit Switch. Heavy Duty Geared Rotary Limit Switch for demanding applications which require trouble free performance. 2 Independent Circuits / Cams / Switches. Precision Snap Acting (SPDT) Single Throw Double Pole Switches. 30 to 1 Gear Ratio. NEMA 12 Enclosure. Maximum speed 1800 RPM, Clock Wise or CCW Rotation. Steel & Bronze Gears. Designed to withstand Rapid Starting, Stopping, Shock & Vibration (8LBS)
2000-2006 Ametek Gemco Rotary Limit Switch. Heavy Duty Geared Rotary Limit Switch for demanding applications which require trouble free performance. 2 Independent Circuits / Cams / Switches. Precision Snap Acting (DPDT) Double Pole Double Throw Switches. 5 to 1 Gear Ratio. NEMA 12 Enclosure. Maximum speed 1800 RPM, Clock Wise or CCW Rotation. Steel & Bronze Gears. Designed to withstand Rapid Starting, Stopping, Shock & Vibration (8LBS)
2000-2021 Ametek Gemco Rotary Limit Switch. Heavy Duty Geared Rotary Limit Switch for demanding applications which require trouble free performance. 4 Independent Circuits / Cams / Switches. Precision Snap Acting (SPDT) Single Throw Double Pole Switches. 15 to 1 Gear Ratio. NEMA 12 Enclosure. Maximum speed 1800 RPM, Clock Wise or CCW Rotation. Steel & Bronze Gears. Designed to withstand Rapid Starting, Stopping, Shock & Vibration (9LBS)
2000-2025 Ametek Gemco Rotary Limit Switch. Heavy Duty Geared Rotary Limit Switch for demanding applications which require trouble free performance. 2 Independent Circuits / Cams / Switches. Precision Snap Acting (SPDT) Single Throw Double Pole Switches. 156.25 to 1 Gear Ratio. NEMA 12 Enclosure. Maximum speed 1800 RPM, Clock Wise or CCW Rotation. Steel & Bronze Gears. Designed to withstand Rapid Starting, Stopping, Shock & Vibration (9LBS)
2000-2027 Ametek Gemco Rotary Limit Switch. Heavy Duty Geared Rotary Limit Switch for demanding applications which require trouble free performance. 2 Independent Circuits / Cams / Switches. Precision Snap Acting (SPDT) Single Throw Double Pole Switches. 250 to 1 Gear Ratio. NEMA 12 Enclosure. Maximum speed 1800 RPM, Clock Wise or CCW Rotation. Steel & Bronze Gears. Designed to withstand Rapid Starting, Stopping, Shock & Vibration (8LBS)
2000-2030 Ametek Gemco Rotary Limit Switch. Heavy Duty Geared Rotary Limit Switch for demanding applications which require trouble free performance. 2 Independent Circuits / Cams / Switches. Precision Snap Acting (SPDT) Single Throw Double Pole Switches. 500 to 1 Gear Ratio. NEMA 12 Enclosure. Maximum speed 1800 RPM, Clock Wise or CCW Rotation. Steel & Bronze Gears. Designed to withstand Rapid Starting, Stopping, Shock & Vibration (8LBS)
2000-2033 Ametek Gemco Rotary Limit Switch. Heavy Duty Geared Rotary Limit Switch for demanding applications which require trouble free performance. 2 Independent Circuits / Cams / Switches. Precision Snap Acting (SPDT) Single Throw Double Pole Switches. 1000 to 1 Gear Ratio. NEMA 12 Enclosure. Maximum speed 1800 RPM, Clock Wise or CCW Rotation. Steel & Bronze Gears. Designed to withstand Rapid Starting, Stopping, Shock & Vibration (8LBS)
2000-2046 Ametek Gemco Rotary Limit Switch. Heavy Duty Geared Rotary Limit Switch for demanding applications which require trouble free performance. 2 Independent Circuits / Cams / Switches. Precision Snap Acting (DPDT) Double Throw Double Pole Switches. 625 to 1 Gear Ratio. NEMA 12 Enclosure. Maximum speed 1800 RPM, Clock Wise or CCW Rotation. Steel & Bronze Gears. Designed to withstand Rapid Starting, Stopping, Shock & Vibration (8LBS)
2000-2048 Ametek Gemco Rotary Limit Switch. Heavy Duty Geared Rotary Limit Switch for demanding applications which require trouble free performance. 2 Independent Circuits / Cams / Switches. Precision Snap Acting (DPDT) Double Throw Double Pole Switches. 1000 to 1 Gear Ratio. NEMA 12 Enclosure Maximum speed 1800 RPM, Clock Wise or CCW Rotation. Steel & Bronze Gears. Designed to withstand Rapid Starting, Stopping, Shock & Vibration (8LBS)
2000-20B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
40 to 1 Ratio Gear Ratio, the cam block rotates once every 40 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet the requirements of NEC code for Class 1, Group D
A NEMA 9 Rated Enclosure is available at the same cost to meet Groups E,F & G. Specify NEMA 7 or 9 when placing any orders
Turns required to reset switch 1/4
Maximum switch setting @ 37 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-2106 Ametek Gemco Limit Switch. NEMA 4 Enclosure, 4 Circuit / Cams, 54 Degree Cams (special), S.P.D.T Switches. ( S0006800) Old Price
2000-2141 Ametek Gemco Limit Switch. 4 Circuit, NEMA 1, 5 to 1 Gear Ratio, Larger SPDT Switches, 2 Standard 25 Degree Cams, 2 Special 180 Degree Cams. Similar to the 2000-89B except for two special cams and larger micro switches Old price
2000-2143 Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
5 to 1 Ratio Gear Ratio, the cam block rotates once every 5 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001
Special Non Standard Cams allow switch contacts to be opened for 54 or 306 Degrees. Other cam dwells are available
NEMA 12 Rated Enclosure
Turns required to reset switch 1/16th
Maximum switch setting @ 4 & 1/2 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(3LBS) 1/8
2000-2148 Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
2000 to 1 Ratio Gear Ratio, the cam block rotates once every 2000 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
3 Standard Cams allow switch contacts to be opened for 25 Degrees. 1 Special 75 Degree Cam
NEMA 4 Rated Cast Aluminum Enclosure, Watertight
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-2179 Ametek Gemco Limit Switch
NEMA 4X Enclosure Bronze
2 Circuit
40 to 1 Gear Ratio
Standard Dwell Cams
2000-2180 Ametek Gemco Limit Switch OBSOLETE Bronze housing is no longer available. See 2000-15B same configuration NEMA 4 Cast Iron Enclosure
2000-2184 Ametek Gemco Rotary Limit Switch, Worm Gear Type, 100 to 1 Ratio, 3 Independent Cams / Switches / Circuits. Single Pole Double Throw Switches, NEMA 4 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance This specially engineered unit has 1 Special Cam S68 at 54 Degrees per factory not S-84A which is 75 degrees. Also includes the physically larger micro-switches and a cover spacer to allow space for these larger switches (7LBS) Old price
2000-21B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
50 to 1 Ratio Gear Ratio, the cam block rotates once every 50 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet the requirements of NEC code for Class 1, Group D
Turns required to reset switch 1/4
Maximum switch setting @ 46 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-2229 Ametek Gemco Rotary Limit Switch, Engineered Part # for Shepard Niles
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
300 to 1 Ratio Gear Ratio, the cam block rotates once every 300 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Special S-68-A Cams allow switch contacts to be opened for 54 or 306 Degrees, dependent on how the switches are wired
NEMA 12 Rated Enclosure
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(3LBS) 1/8
2000-2235 Ametek Gemco Rotary Limit Switch, NEMA 1 Enclosure, 600 to 1 ratio, 2 Circuit with special S68 Cams
2000-2237 Ametek Gemco Rotary Limit Switch, Worm Gear Type, 1000 to 1 Gear Ratio, Qty. 2, Independent Cams / Circuits / Switches, S.P.D.T. Single Pole Double Throw Precision Snap Switches, NEMA 1 & 12 Enclosure, Special Cams # S-68-A @ 54 Degrees, Maximum Speed 1000 RPM Clock Wise or CCW. 1/2 Inch Diameter Input Shaft includes a # 404 Woodruff Key, 1/2 - 14 American Standard Pipe Thread Entrance (4LBS)
2000-2248 Ametek Gemco Rotary Limit Switch, Worm Gear Type, 10 to 1 Ratio, 2 Cam, Single Pole Double Throw Snap Action Switches 2, which are independently adjustable, NEMA 7, Hazardous Location,Cast Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance. Max 18 turns to set switch, 1/8 turn to reset switch, Max. Operating Temp 180 F., This unit has optional 54 Degree Cams (2LBS)
2000-2254 Ametek Gemco Geared Limit Switch built and sold exclusively by OEM Account. Altec Industries Inc. NEMA 1 , Rubber Gasket
2000-2262 Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Qty. 4, Non-Standard Cams, S0006900, which allow switch contacts to be opened for 90 or 270 Degrees
NEMA 1 & 12 Enclosure
Turns required to reset switch 1/8th
Maximum switch setting @ 19 & 1/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-22B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
60 to 1 Ratio Gear Ratio, the cam block rotates once every 60 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 7 Rated Enclosure, NEMA 9 same cost but must specify 9 at time of order
Turns required to reset switch 1 & 1/2
Maximum switch setting @ 58 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-23B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
80 to 1 Ratio Gear Ratio, the cam block rotates once every 80 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 7 Rated Enclosure, NEMA 9 same cost but must specify 9 at time of order
Turns required to reset switch 3/4
Maximum switch setting @ 77 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-2401 Ametek Gemco Rotary Limit Switch, Worm Gear Type, 100 to 1 Ratio, 3 Cam, Single Pole Double Throw Switches, NEMA 1 & 12 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance. 3 LBS Gross Special, includes 2, 54 degree cams & 1, 25 Degree cam. Periods for which Switch Contacts are Opened or Closed.
2000-2459 Ametek Gemco Geared Rotary Limit Switch (3LBS) Old Price
2000-2463 Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Non-Standard Cams S68A allow switch contacts to be opened for 54 or 306 Degrees. Other cam dwells are available
NEMA 12 Enclosure
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(3LBS)
2000-2479 Ametek Gemco Rotary Limit Switch, Worm Gear Type with a 20 to 1 Gear Ratio. Qty. 2, Independent Cams / Circuits / Switches. U.L. Listed Precision Snap Acting Switches, S.P.D.T. Single Pole Double Throw which can be wired Normally Open or Normally Closed. Both Cams are part # S71A at 240 Degrees. NEMA 1 & 12 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance. (6LBS)
2000-2489 Ametek Gemco Limit Switch. Series 2000 Geared Rotary Limit Switch. 4 Independent Circuits / Cams / Switches. SPDT Switches. 2000 to 1 Gear Ratio. NEMA 4 Enclosure. 5K pot and 1 of the four cams is S-0008400, a 75 degree cam Old price
2000-2490 Ametek Gemco Geared Rotary Limit Switch. 4 Circuit / Cams. 2 Cams are Special 75 Degree Cams. 10 to 1 Gear Ratio with a NEMA 1 Enclosure (2LBS)
2000-24B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
100 to 1 Ratio Gear Ratio, the cam block rotates once every 100 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 7 Rated Enclosure, NEMA 9 same cost but must specify 9 at time of order
Turns required to reset switch 3/4
Maximum switch setting @ 94 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-2516 Ametek Gemco Rotary Limit Switch, Worm Gear Type, 600 to 1 Gear Ratio, Qty. 2, Independent Cam / Circuit / Switches, S.P.D.T. Single Pole Double Throw Switches, NEMA 4 Rated Watertight Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance
S0008700 Cams 150 or 210 Degree (3LBS)
2000-2539 Ametek Gemco Geared Limit Switch. 6 Circuits / Cams / Switches. 250 Gear Ratio. NEMA 12 Enclosure. Single Pole Double Throw Switches (Licon) 25 Degree Cams Old price
2000-2564 Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
60 to 1 Ratio Gear Ratio, the cam block rotates once every 60 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Cast Bronze Enclosure, Watertight
Turns required to reset switch 1 & 1/2
Maximum switch setting @ 58 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Stainless Steel Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS) 1/8
2000-2583 Ametek Gemco Rotary Limit Switch, Worm Gear Type, 20 to 1 Ratio, 3 Independent Cams / Switches / Circuits. Single Pole Double Throw Switches, NEMA 1 & 12 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance. Special with all 90 Degree Cams S-69-A & Physically Larger Snap Switches (7LBS) Old price
2000-2591 Ametek Gemco Geared Rotary Limit Switch
2000 = 2000 Series
2591 = Specially Engineered Product
3 Circuits
3 Special Cams having a Dwell of 90 Degrees
60 to 1 Gear Ratio
NEMA 1 Enclosure 1/8

2000-25B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 1/2
Maximum switch setting @ 19 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-2617 Ametek Gemco Geared Rotary Limit Switch. 5 Independent Circuits / Switches / Cams. SPDT Licon Switches, 5 to 1 Gear Ratio, NEMA 1 Enclosure (4LBS) 1/6
2000-2634A Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
1000 to 1 Ratio Gear Ratio, the cam block rotates once every 1000 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. Form ''C'' 3 Screw Terminals. The common is shared by both contacts
2 Custom Engineered Cams with 130 Degrees of Dwell
1st Non-Standard Cam S-71-A allows one switch contact to be opened for 240 or 120 Degrees
2nd Non-Standard Cam S-86-A allows one switch contact to be opened for 135 or 225 Degrees
NEMA 1 & 12 Enclosure
Turns required to reset switch 29
Maximum switch setting @ 920 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(3LBS)
2000-2642 Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
30 to 1 Ratio Gear Ratio, the cam block rotates once every 30 turns of the main shaft
3 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537004
2 Special Cams with 30 degrees of dwell
1 Cam S70 with 180 degrees of dwell
NEMA 12 Rated Enclosure
Turns required to reset switch 1/4
Maximum switch setting @ 28 & 1/2 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
Tall Cover
(4LBS)
2000-264B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
10 to 1 Ratio Gear Ratio, the cam block rotates once every 10 turns of the main shaft
3 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet the requirements of NEC code for Class 1, Group D
A NEMA 9 Rated Enclosure is available at the same cost to meet Groups E,F & G. Specify NEMA 7 or 9 when placing any orders
Turns required to reset switch 1/16
Maximum switch setting @ 9 & 1/2 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-266B Ametek Gemco
2000-267B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
40 to 1 Ratio Gear Ratio, the cam block rotates once every 40 turns of the main shaft
3 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet the requirements of NEC code for Class 1, Group D
A NEMA 9 Rated Enclosure is available at the same cost to meet Groups E,F & G. Specify NEMA 7 or 9 when placing any orders
Turns required to reset switch 1/2
Maximum switch setting @ 38 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-2687 Ametek Gemco Limit Switch. NEMA 4 Aluminum Enclosure, Resolver & Plug, 72 to 1 Ratio.
2000-2701 Ametek Gemco Limit Switch with 300:1, NEMA 4, SPDT, cast iron enclosure, 2x586A cams.
2000-2703 Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears, Steel Cams and a Stainless Steel Shaft
10 to 1 Ratio Gear Ratio, the cam block rotates once every 10 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 12 Fibralloy Enclosure
Turns required to reset switch 1/16th
Maximum switch setting @ 9.5 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-2704 Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
30 to 1 Ratio Gear Ratio, the cam block rotates once every 30 turns of the main shaft
3 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537004
1 Standard Cams allow switch contacts to be opened for 25 or 335 Degrees
2 Non-Standard Cams S68A allow switch contacts to be opened for 54 or 306 Degrees
NEMA 12 Enclosure
Turns required to reset switch 1/4
Maximum switch setting @ 28 & 1/2 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-273B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
500 to 1 Ratio Gear Ratio, the cam block rotates once every 500 turns of the main shaft
3 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet the requirements of NEC code for Class 1, Group D
A NEMA 9 Rated Enclosure is available at the same cost to meet Groups E,F & G. Specify NEMA 7 or 9 when placing any orders
Turns required to reset switch 7
Maximum switch setting @ 460 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-2757 Ametek Gemco Geared Rotary Limit Switch. 5 Independent Circuits / Cams / Switches in a NEMA 1 / 12 Enclosure with a 20 to 1 Gear Ratio and Single Pole Double Throw Precision Snap Action Switches. Cams = Qty. 4 Standard Cams S0005500 @ 25 Degrees & Qty. 1, Special Cam @ S0007000 180 Degrees
2000-2760 Ametek Gemco Rotary Limit Switch, Like 2000-14B
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
60 to 1 Ratio Gear Ratio, the cam block rotates once every 60 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Non-Standard Cams S68 allow switch contacts to be opened for 54 or 306 Degrees. Other cam dwells are available
NEMA 4 Rated Cast Aluminum Enclosure, Watertight
Turns required to reset switch 1 & 1/2
Maximum switch setting @ 58 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-2778 Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
50 to 1 Ratio Gear Ratio, the cam block rotates once every 50 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001
1 Standard Cam allow switch contacts to be opened for 25 or 335 Degrees
1 Special Cam S84 allows the switch contacts to be opened for 75 or 285 Degrees
Other cam dwells are available
NEMA 12 Rated Enclosure
Turns required to reset switch 1/4
Maximum switch setting @ 46 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(3LBS)
2000-2779 Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. Qty. 4, Independent Cams / Circuits / Switches with Single Pole Double Throw Snap Action Switches (S.P.D.T.) 20 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Stainless Steel Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F. (6LBS) 10/5
2000-2786 Ametek Gemco Series 2000 Worm Gear Type Rotary Limit Switch. 4 Independently Adjustable Standard Cams / Circuits, UL Listed snap action S.P.D.T Switches, NEMA 1 & 12 Fibralloy Enclosure, 100 to 1 Ratio. 1/2 Inch input shaft with woodruff key. Maximum RPM 1000. Maximum operating temperature 180 degree F.
2000-2791 Ametek Gemco Geared Rotary Limit Switch. NEMA 4 Enclosure, 40 to 1 Gear Ratio, 4 Circuit / Cams with Special 54 Degree Cams, S.P.D.T Switches. (S0006800)
2000-279B Ametek Gemco Rotary Limit Switch, Worm Gear Type, 4000 to 1 Ratio, 2 Cam, S.P.D.T. Single Pole Double Throw Switches, NEMA 12 Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance (3LBS)
2000-28B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
250 to 1 Ratio Gear Ratio, the cam block rotates once every 250 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 12 Rated Enclosure
Turns required to reset switch, 6
Maximum switch setting @ 230 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(3LBS)
2000-291B Ametek Gemco Rotary Limit Switch. Worm Gear Type, Two Independent Circuits / Switches / Cams. 2000 to 1 Gear Ratio. UL Listed S.P.D.T. Precision Snap Action Switches. NEMA 7 & 9 Rated Die Cast Aluminum Enclosure for Hazardous Locations, designed to meet the NEC Code for Class 1, Group D, and Class 2, Groups E, F & G Locations. Maximum Speed 1000 RPM (6LBS)
2000-292B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
2000 to 1 Ratio Gear Ratio, the cam block rotates once every 2000 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 12 Enclosure
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(3LBS)
2000-2958 Ametek Gemco Rotary Limit Switch. NEMA 7 Enclosure with a 1 k Ohm Pot.
2000-299B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
2000 to 1 Ratio Gear Ratio, the cam block rotates once every 2000 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Cast Aluminum Enclosure, Watertight
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-29B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
500 to 1 Ratio Gear Ratio, the cam block rotates once every 500 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 15 & 1/4
Maximum switch setting @ 460 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(3LBS)
2000-2B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 12 Rated Enclosure
Turns required to reset switch 1/8
Maximum switch setting @ 18 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(3LBS)
2000-300B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
300 to 1 Ratio Gear Ratio, the cam block rotates once every 300 turns of the main shaft
3 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Cast Aluminum Enclosure, Watertight
Turns required to reset switch 6 & 1/2
Maximum switch setting @ 265 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(5LBS)
2000-3036 Ametek Gemco 2000-3036 is a NEMA 1, 2 circuit, 100:1 ratio with 75 degree cams. So the 3036 may mean something else cause its not NEMA 7.
2000-3047 Ametek Gemco Geared Rotary Limit Switch. Series 2000. NEMA 1 Enclosure. 3 Independent Circuits/ Cams / Switches. Single Pole Double Throw Snap Switches. 20 to 1 Gear Ratio. Special 90 Degree Cams & a Tall Cover 10/7
2000-3058 Ametek Gemco Rotary Limit Switch. Series 2000 Worm Gear Type. 2 Independent Cams / Circuits / Switches with Single Pole Double Throw Snap Action Switches, 60 to 1 Gear Ratio. Cast Aluminum NEMA Type 4 Watertight Enclosure. Up to 1000 RPM no minimum. Clock Wise or CCW Rotation. 1/2 Inch Diameter Input Shaft with a # 404 Woodruff Key & Keyway. 1/2 -14 American Standard Pipe Thread Electrical Entrance. Maximum operating temperature 180 degrees F Special engineered part number. With Stainless Steel Input Shaft PM0039100 (6LBS)
2000-3059 Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
60 to 1 Ratio Gear Ratio, the cam block rotates once every 60 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
2 Standard Cams S005500 in switch positions 1 and 4 allow switch contacts to be opened for 25 or 335 Degrees
2 Special Cams S0006800 in switch positions 2 and 3 allow switch contacts to be opened for 54 or 306 Degrees
NEMA 1 & 12 Enclosure
Turns required to reset switch 1/2
Maximum switch setting @ 76 & 3/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-3063 Ametek Gemco Rotary Limit Switch. Spur Gear Type, Four Independent Circuits / Cam / Switches, UL Listed Snap Action Switches with S.P.D.T. Contacts, Die Cast NEMA 4 Enclosure, 1/2 to 1 input shaft revolution to 1 cam block revolution. For basic switch data see table 2 symbol C
Special with Qty. 2, S71 Cams in Circuits 2 & 3
2000-3070 Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
1000 to 1 Ratio Gear Ratio, the cam block rotates once every 1000 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. Form ''C'' 3 Screw Terminals. The common is shared by both contacts
2 Custom Engineered Cams with 130 Degrees of Dwell
NEMA 1 & 12 Enclosure
Turns required to reset switch 29
Maximum switch setting @ 920 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(3LBS)
2000-3071 Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
1000 to 1 Ratio Gear Ratio, the cam block rotates once every 1000 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. Form ''C'' 3 Screw Terminals. The common is shared by both contacts
1 Custom Engineered Cam with 200 Degrees of Dwell
1 Custom Engineered Cam with 285 Degrees of Dwell
NEMA 1 & 12 Enclosure
Turns required to reset switch 29
Maximum switch setting @ 920 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(3LBS) 11/7
2000-3077 Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
60 to 1 Ratio Gear Ratio, the cam block rotates once every 60 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
2 Standard Cams in positions 1 and 4 allow switch contacts to be opened for 25 or 335 Degrees
2 Optional Cams # S68 in positions 2 and 3 allow switch contacts to be opened for 54 or 306 Degrees
NEMA 4 Rated Enclosure
Turns required to reset switch 1/2
Maximum switch setting @ 57 & 1/2 Turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-3078 Ametek Gemco Rotary Limit Switch, Worm Gear Type, 1000 to 1 Ratio, Qty. 3 Non-Standard Cams S84 @ 75 Degrees, Single Pole Double Throw Switches, NEMA 4 Rated Enclosure, Maximum Speed 1000 RPM Clock Wise or CCW., 1/2 Inch Diameter Input Shaft, includes # 404 Woodruff Keyway, 1/2 -14 American Standard Pipe Thread Entrance (4LBS) 11/7
2000-30B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
1000 to 1 Ratio Gear Ratio, the cam block rotates once every 1000 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 29
Maximum switch setting @ 920 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(3LBS)
2000-31B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
250 to 1 Ratio Gear Ratio, the cam block rotates once every 250 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Cast Aluminum Enclosure, Watertight
Turns required to reset switch 6
Maximum switch setting @ 230 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-32B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
500 to 1 Ratio Gear Ratio, the cam block rotates once every 500 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Cast Aluminum Enclosure, Watertight
Turns required to reset switch 15 & 1/4
Maximum switch setting @ 460 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-33B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
1000 to 1 Ratio Gear Ratio, the cam block rotates once every 1000 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Cast Aluminum Enclosure, Watertight
Turns required to reset switch 29
Maximum switch setting @ 920 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-34B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
250 to 1 Ratio Gear Ratio, the cam block rotates once every 250 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet requirements for NEC Class 1, Group D and Class 2 Groups E,F & G. Cast Iron & Bronze are available
Turns required to reset switch, 6
Maximum switch setting @ 230 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(2LBS)
2000-38B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
10 to 1 Ratio Gear Ratio, the cam block rotates once every 10 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 12 Rated Enclosure
Turns required to reset switch 1/8th
Maximum switch setting @ 9 & 1/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(3LBS)
2000-39B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
10 to 1 Ratio Gear Ratio, the cam block rotates once every 10 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals # 04537004
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Cast Aluminum Enclosure, Watertight
Turns required to reset switch 1/8
Maximum switch setting @ 9 & 1/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(5LBS)
2000-3B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
30 to 1 Ratio Gear Ratio, the cam block rotates once every 30 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 12 Rated Enclosure
Turns required to reset switch 1/4
Maximum switch setting @ 28 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(3LBS)
2000-40B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
10 to 1 Ratio Gear Ratio, the cam block rotates once every 10 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet the requirements of NEC code for Class 1, Group D
A NEMA 9 Rated Enclosure is available at the same cost to meet Groups E,F & G. Specify NEMA 7 or 9 when placing any orders
Turns required to reset switch 1/8th
Maximum switch setting @ 9 & 1/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-43B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
100 to 1 Ratio Gear Ratio, the cam block rotates once every 100 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 2
Maximum switch setting @ 95 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-47B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
30 to 1 Ratio Gear Ratio, the cam block rotates once every 30 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 1/2
Maximum switch setting @ 28 & 1/2 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-4B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
40 to 1 Ratio Gear Ratio, the cam block rotates once every 40 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 12 Rated Enclosure
Turns required to reset switch 1/4
Maximum switch setting @ 37 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(3LBS)
2000-59 Ametek Gemco Series 2000 Worm Gear Type Rotary Limit Switch. 2 Cam, 100 to 1 with Special Cams 54 Degree, SPDT
2000-5B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
50 to 1 Ratio Gear Ratio, the cam block rotates once every 50 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 12 Rated Enclosure
Turns required to reset switch 1/4
Maximum switch setting @ 46 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(3LBS)
2000-60B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
30 to 1 Ratio Gear Ratio, the cam block rotates once every 30 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 7 Rated Cast Aluminum Enclosure for Hazardous Locations. Designed to meet the requirements of NEC code for Class 1, Group D
Turns required to reset switch 1/2
Maximum switch setting @ 28 & 1/2 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-6B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
60 to 1 Ratio Gear Ratio, the cam block rotates once every 60 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 12 Rated Enclosure
Turns required to reset switch 1 & 1/2
Maximum switch setting @ 58 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(3LBS)
2000-73B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
50 to 1 Ratio Gear Ratio, the cam block rotates once every 50 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 3/4
Maximum switch setting @ 46 & 3/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-75B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
60 to 1 Ratio Gear Ratio, the cam block rotates once every 60 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 1 & 1/2
Maximum switch setting @ 58 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-77B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
80 to 1 Ratio Gear Ratio, the cam block rotates once every 80 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Double Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 8 Screw Terminals per switch
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 1 & 3/4
Maximum switch setting @ 75 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-7B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
80 to 1 Ratio Gear Ratio, the cam block rotates once every 80 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 12 Rated Enclosure
Turns required to reset switch 3/4
Maximum switch setting @ 77 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(3LBS)
2000-800 Ametek Gemco Rotary Limit Switch
2000-800 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
2 Independent Circuit / Cams / Switches
S.P.D.T. Snap Action U.L. Listed Switches # 04537001 & 04537002
Basic Switch Data see Table 2 Symbol A on Page 13
NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover
1 to 1 Input Shaft Ratio, Every 1 Turns of the Main Shaft Cam Rotates Once
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure
Includes Keyway & a #404 Woodruff Key
3/4 -14 N.P.T. Electrical Entrance
(4LBS)
2000-801 Ametek Gemco Rotary Limit Switch
2000-801 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
2 Independent Circuit / Cams / Switches
S.P.D.T. Snap Action U.L. Listed Switches
Basic Switch Data see Table 2 Symbol A on Page 13
NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover
1/2 to 1 Input Shaft Ratio, Every 1/2 Turns of the Main Shaft Cam Rotates Once
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure
Includes Keyway & a #404 Woodruff Key
3/4 -14 N.P.T. Electrical Entrance
(4LBS)
2000-802 Ametek Gemco Rotary Limit Switch
2000-802 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
2 Independent Circuit / Cams / Switches
S.P.D.T. Snap Action U.L. Listed Switches
Basic Switch Data see Table 2 Symbol A on Page 13
NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover
1/3 to 1 Input Shaft Ratio, Every 1/3 Turns of the Main Shaft Cam Rotates Once
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure
Includes Keyway & a #404 Woodruff Key
3/4 -14 N.P.T. Electrical Entrance
(4LBS)
2000-803 Ametek Gemco Rotary Limit Switch
2000-803 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
2 Independent Circuit / Cams / Switches
S.P.D.T. Snap Action U.L. Listed Switches
Basic Switch Data see Table 2 Symbol A on Page 13
NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover
2 to 1 Input Shaft Ratio, Every 2 Turns of the Main Shaft Cam Rotates Once
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure
Includes Keyway & a #404 Woodruff Key
3/4 -14 N.P.T. Electrical Entrance
(4LBS)
2000-804 Ametek Gemco Rotary Limit Switch
2000-804 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
2 Independent Circuit / Cams / Switches
S.P.D.T. Snap Action U.L. Listed Switches
Basic Switch Data see Table 2 Symbol A on Page 13
NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover
3 to 1 Input Shaft Ratio, Every 3 Turns of the Main Shaft Cam Rotates Once
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure
Includes Keyway & a #404 Woodruff Key
3/4 -14 N.P.T. Electrical Entrance
(4LBS)
2000-805 Ametek Gemco Rotary Limit Switch
2000-805 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
2 Independent Circuit / Cams / Switches
D.P.D.T. Snap Action U.L. Listed Switches
Basic Switch Data see Table 2 Symbol B on Page 13
NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover
1 to 1 Input Shaft Ratio, Every 1 Turns of the Main Shaft Cam Rotates Once
Maximum Turns to set the switch 0.9, minimum 0.05, 0.025 to reset the switch
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure
Includes Keyway & a #404 Woodruff Key
3/4 -14 N.P.T. Electrical Entrance
(4LBS)
2000-807 Ametek Gemco Rotary Limit Switch
2000-807 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
2 Independent Circuit / Cams / Switches
D.P.D.T. Snap Action U.L. Listed Switches
Basic Switch Data see Table 2 Symbol B on Page 13
NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover
1/3 to 1 Input Shaft Ratio, Every 1/3 Turn of the Main Shaft Cam Rotates Once
Maximum Turns to set the switch .3, minimum 0.106, 0.008 to reset the switch
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure
Includes Keyway & a #404 Woodruff Key
3/4 -14 N.P.T. Electrical Entrance
(4LBS)
2000-808 Ametek Gemco Rotary Limit Switch
2000-808 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
2 Independent Circuit / Cams / Switches
D.P.D.T. Snap Action U.L. Listed Switches
Basic Switch Data see Table 2 Symbol B on Page 13
NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover
2 to 1 Input Shaft Ratio, Every 2 Turns of the Main Shaft Cam Rotates Once
Maximum Turns to set the switch 1.8, minimum 0.1, 0.050 to reset the switch
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure
Includes Keyway & a #404 Woodruff Key
3/4 -14 N.P.T. Electrical Entrance
(4LBS)
2000-809 Ametek Gemco Rotary Limit Switch
2000-809 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
2 Independent Circuit / Cams / Switches
D.P.D.T. Snap Action U.L. Listed Switches
Basic Switch Data see Table 2 Symbol B on Page 13
NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover
3 to 1 Input Shaft Ratio, Every 3 Turns of the Main Shaft Cam Rotates Once
Maximum Turns to set the switch 2.7, minimum 0.15, 0.075 to reset the switch
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure
Includes Keyway & a #404 Woodruff Key
3/4 -14 N.P.T. Electrical Entrance
(4LBS)
2000-813 Ametek Gemco Rotary Limit Switch
2000-818 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
3 Independent Circuits / Cams / Switches
S.P.D.T. Snap Action U.L. Listed Switches # 04537004
Basic Switch Data see Table 2 Symbol C on Page 13
NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover
2 to 1 Input Shaft Ratio, Every Two Turns of the Main Shaft the Cam Block Rotates Once
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from the Enclosure
Includes Woodruff Keyway & a #404 Woodruff Key
0.0120 Turns to Reset
0.050 Turns to Reset
3/4 -14 N.P.T. Electrical Entrance
(4LBS)
2000-814 Ametek Gemco Rotary Limit Switch
2000-814 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
3 Independent Circuits / Cams / Switches
S.P.D.T. Snap Action U.L. Listed Switches # 04537004
Basic Switch Data see Table 2 Symbol C on Page 13
NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover
3 to 1 Input Shaft Ratio, Every 3 Turns of the Main Shaft the Cam Block Rotates Once
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from the Enclosure
Includes Woodruff Keyway & a #404 Woodruff Key
0.075 Turns to Reset
3/4 -14 N.P.T. Electrical Entrance
(4LBS)
2000-815 Ametek Gemco Rotary Limit Switch
2000-815 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
4 Independent Circuits / Cams / Switches
S.P.D.T. Snap Action U.L. Listed Switches #
Basic Switch Data see Table 2 Symbol C on Page 13
NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover
1 to 1 Input Shaft Ratio, Every Turn of the Main Shaft the Cam Block Rotates Once
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from the Enclosure
Includes Woodruff Keyway & a #404 Woodruff Key
0.025 Turns to Reset the Switch
3/4 -14 N.P.T. Electrical Entrance
(4LBS)
2000-816 Ametek Gemco Rotary Limit Switch
2000-816 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
4 Independent Circuits / Cams / Switches
S.P.D.T. Snap Action U.L. Listed Switches #
Basic Switch Data see Table 2 Symbol C on Page 13
NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover
1 to 1 Input Shaft Ratio, Every Turn of the Main Shaft the Cam Block Rotates Once
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from the Enclosure
Includes Woodruff Keyway & a #404 Woodruff Key
0.0120 Turns to Reset
3/4 -14 N.P.T. Electrical Entrance
(4LBS)
2000-817 Ametek Gemco Rotary Limit Switch
2000-817 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
4 Independent Circuits / Cams / Switches
S.P.D.T. Snap Action U.L. Listed Switches #
Basic Switch Data see Table 2 Symbol C on Page 13
NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover
1 to 1 Input Shaft Ratio, Every Turn of the Main Shaft the Cam Block Rotates Once
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from the Enclosure
Includes Woodruff Keyway & a #404 Woodruff Key
0.008 Turns to Reset
3/4 -14 N.P.T. Electrical Entrance
(4LBS)
2000-818 Ametek Gemco Rotary Limit Switch
2000-818 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
4 Independent Circuits / Cams / Switches
S.P.D.T. Snap Action U.L. Listed Switches #
Basic Switch Data see Table 2 Symbol C on Page 13
NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover
2 to 1 Input Shaft Ratio, Every Two Turn of the Main Shaft the Cam Block Rotates Once
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from the Enclosure
Includes Woodruff Keyway & a #404 Woodruff Key
0.0120 Turns to Reset
0.050 Turns to Reset
3/4 -14 N.P.T. Electrical Entrance
(4LBS)
2000-819 Ametek Gemco Rotary Limit Switch
2000-819 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
4 Independent Circuits / Cams / Switches
S.P.D.T. Snap Action U.L. Listed Switches #
Basic Switch Data see Table 2 Symbol C on Page 13
NEMA 1 & 12 Rated Die Cast Enclosure with Fibralloy Cover
3 to 1 Input Shaft Ratio, Every 3 Turns of the Main Shaft the Cam Block Rotates Once
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from the Enclosure
Includes Woodruff Keyway & a #404 Woodruff Key
0.075 Turns to Reset
3/4 -14 N.P.T. Electrical Entrance
(4LBS)
2000-820 Ametek Gemco Rotary Limit Switch
Spur Gear Type with Potentiometer
NEMA 12 Rated Die Cast Housing with a Fibralloy Cover
Gear Ratio is 1 to 1 from the Main Shaft to the Cam Block & the Potentiometer
Two SPDT Switches. Basic Switch Data see symbol A page 12
Potentiometers are rated at 2 Watts
Many resistance values are available
Quoting a 5K resistance potentiometer
Unique mounting features permit the switch to be mounted in any of 3 different positions. Mounting holes are independent of the enclosure cover

2000-832 Ametek Gemco Rotary Limit Switch
2000-832 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
2 Independent Circuit / Cams / Switches
S.P.D.T. Snap Action U.L. Listed Switches
Basic Switch Data see Table 2 Symbol A on Page 13
NEMA 4 Rated Die Cast Enclosure
1 to 1 Input Shaft Ratio, Every 1 Turn of the Main Shaft Cam Rotates Once
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure
Includes Keyway & a #404 Woodruff Key
3/4 -14 N.P.T. Electrical Entrance
(5LBS)
2000-833 Ametek Gemco Rotary Limit Switch. Spur Gear Type, Two Independent Circuits, UL Listed Snap Action Switches with S.P.D.T. Contacts, NEMA 4 Enclosure, 1/2 to 1 Input Shaft Ratio. For basic switch data see table 2 symbol A
2000-834 Ametek Gemco Rotary Limit Switch. Spur Gear Type, Two Independent Circuits, UL Listed Snap Action Switches with S.P.D.T. Contacts, Die Cast NEMA 4 Enclosure, 1/3rd to 1 Input Shaft Revolution, 1 Cam Block Revolution. For basic switch data see table 2 symbol A.
2000-835 Ametek Gemco Rotary Limit Switch
2000-835 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
2 Independent Circuit / Cams / Switches
S.P.D.T. Snap Action U.L. Listed Switches # 04537001 & 04537002
Basic Switch Data see Table 2 Symbol A on Page 13
NEMA 4 Die Cast Enclosure
2 to 1 Input Shaft Ratio, Every 2 Turns of the Main Shaft Cam Rotates Once
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure
Includes Keyway & a #404 Woodruff Key
3/4 -14 N.P.T. Electrical Entrance
(4LBS)
2000-836 Ametek Gemco Rotary Limit Switch. Spur Gear Type, Two Independent Circuits, Cams, Switches. UL Listed Snap Action Switches with S.P.D.T. Contacts, NEMA 4 Enclosure, 3 to 1 Input Shaft Ratio. For basic switch data see table 2 symbol A
2000-837 Ametek Gemco Rotary Limit Switch
2000-841 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
2 Independent Circuit / Cams / Switches
D.P.D.T. Snap Action U.L. Listed Switches
Basic Switch Data see Table 2 Symbol B on Page 13
NEMA 4 Rated Die Cast Enclosure, Watertight
1 to 1 Input Shaft Ratio, Every 1Turn of the Main Shaft Cam Rotates Once
Maximum Turns to set the switch 0.9, minimum 0.05, 0.025 to reset the switch
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure
Includes Keyway & a #404 Woodruff Key
3/4 -14 N.P.T. Electrical Entrance
2000-839 Ametek Gemco Rotary Limit Switch
2000-841 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
2 Independent Circuit / Cams / Switches
D.P.D.T. Snap Action U.L. Listed Switches
Basic Switch Data see Table 2 Symbol B on Page 13
NEMA 4 Rated Die Cast Enclosure, Watertight
1/3 to 1 Input Shaft Ratio, Every 1/3 Turn of the Main Shaft Cam Rotates Once
Maximum Turns to set the switch 0.30, minimum 0.16, 0.008 to reset the switch
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure
Includes Keyway & a #404 Woodruff Key
3/4 -14 N.P.T. Electrical Entrance
2000-841 Ametek Gemco Rotary Limit Switch
2000-841 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
2 Independent Circuit / Cams / Switches
D.P.D.T. Snap Action U.L. Listed Switches
Basic Switch Data see Table 2 Symbol B on Page 13
NEMA 4 Rated Die Cast Enclosure, Watertight
3 to 1 Input Shaft Ratio, Every 3 Turns of the Main Shaft Cam Rotates Once
Maximum Turns to set the switch 2.7, minimum 0.15, 0.075 to reset the switch
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure
Includes Keyway & a #404 Woodruff Key
3/4 -14 N.P.T. Electrical Entrance
2000-842 Ametek Gemco Rotary Limit Switch
2000-842 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
3 Independent Circuit / Cams / Switches
S.P.D.T. Snap Action U.L. Listed Switches # 04537004
Basic Switch Data see Table 2 Symbol C on Page 13
NEMA 4 Rated Die Cast Aluminum Enclosure
1 to 1 Input Shaft Ratio, Every 1 Turns of the Main Shaft Cam Rotates Once
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure
Includes Keyway & a #404 Woodruff Key
3/4 -14 N.P.T. Electrical Entrance
(5LBS)
2000-844 Ametek Gemco Rotary Limit Switch. Spur Gear Type, Three Independent Circuits / Cam / Switches, UL Listed Snap Action Switches with S.P.D.T. Contacts, Die Cast NEMA 4 Enclosure, 1/3rd input shaft revolution to 1 cam block revolution. For basic switch data see table 2 symbol C.
2000-847 Ametek Gemco Rotary Limit Switch
2000-847 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
4 Independent Circuit / Cams / Switches
S.P.D.T. Snap Action U.L. Listed Switches # 04537004
Basic Switch Data see Table 2 Symbol C on Page 13
NEMA 4 Rated Die Cast Aluminum Enclosure
1 to 1 Input Shaft Ratio, Every Turn of the Main Shaft Cam Rotates Once
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure
Includes Keyway & a #404 Woodruff Key
0.025 Turns to Reset
3/4 -14 N.P.T. Electrical Entrance
(4LBS)
2000-848 Ametek Gemco Rotary Limit Switch
2000-848 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
4 Independent Circuit / Cams / Switches
S.P.D.T. Snap Action U.L. Listed Switches # 04537004
Basic Switch Data see Table 2 Symbol C on Page 13
NEMA 4 Rated Die Cast Aluminum Enclosure
1/2 to 1 Input Shaft Ratio, Every 1/2 Turn of the Main Shaft Cam Rotates Once
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure
Includes Keyway & a #404 Woodruff Key
0.0120 Turns to Reset
3/4 -14 N.P.T. Electrical Entrance
(4LBS)
2000-849 Ametek Gemco Rotary Limit Switch
2000-849 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
4 Independent Circuit / Cams / Switches
S.P.D.T. Snap Action U.L. Listed Switches # 04537004
Basic Switch Data see Table 2 Symbol C on Page 13
NEMA 4 Rated Die Cast Aluminum Enclosure
1/3 to 1 Input Shaft Ratio, Every 1/3 Turn of the Main Shaft Cam Rotates Once
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure
Includes Keyway & a #404 Woodruff Key
0.008 Turns to Reset
3/4 -14 N.P.T. Electrical Entrance
(4LBS)
2000-850 Ametek Gemco Rotary Limit Switch
2000-850 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
4 Independent Circuit / Cams / Switches
S.P.D.T. Snap Action U.L. Listed Switches # 04537004
Basic Switch Data see Table 2 Symbol C on Page 13
NEMA 4 Rated Die Cast Aluminum Enclosure
2 to 1 Input Shaft Ratio, Every 2 Turns of the Main Shaft Cam Rotates Once
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure
Includes Keyway & a #404 Woodruff Key
0.050 Turns to Reset
3/4 -14 N.P.T. Electrical Entrance
(4LBS)
2000-851 Ametek Gemco Rotary Limit Switch
2000-851 Spur Gear Type for Ultra Sensitive Control of Small Increments of Motion
4 Independent Circuit / Cams / Switches
S.P.D.T. Snap Action U.L. Listed Switches # 04537004
Basic Switch Data see Table 2 Symbol C on Page 13
NEMA 4 Rated Die Cast Aluminum Enclosure
3 to 1 Input Shaft Ratio, Every 3 Turns of the Main Shaft Cam Rotates Once
1/2 Inch Diameter Main Shaft which Extends 1 & 1/2 Inch from Enclosure
Includes Keyway & a #404 Woodruff Key
3/4 -14 N.P.T. Electrical Entrance
(4LBS)
2000-854 Ametek Gemco Limit Switch. Series 2000 Spur Gear Type Rotary Limit Switch with Potentiometer 04516086 100 OHM
2 Circuit / Cam / Switches
SPDT Switches, Single Pole Double Throw, Basic Switch Data Symbol ''A'' page 13
0.9 Degree of a Turn Maximum setting between settings
0.05 Degree of a Turn Minimum setting between settings
0.025 Degree of a Turn to Reset the Switch
1 to 1 Ratio, Spur Gear Ratio, Cam bock turns once every revolution of the main shaft
1 to 3 Potentiometer Ratio. Potentiometers are rated @ 2 Watts, Linear Taper
Standard Cams, 25 or 335 Degree
1/2 Inch Diameter Output Shaft with a No 404 Woodruff Key & Keyway
NEMA 4 Rated Enclosure, Watertight
(5LBS) 10/7
2000-864 Ametek Gemco Rotary Limit Switch. Spur Gear Type, Two Independent Circuits, Cam / Switches. UL Listed Snap Action Switches with S.P.D.T. Contacts, NEMA 7 Enclosure, 1 to 1 Input Shaft Ratio. For basic switch data see table 2 symbol A
2000-865 Ametek Gemco Rotary Limit Switch. Spur Gear Type, Two Independent Circuits, Cam / Switches. UL Listed Snap Action Switches with S.P.D.T. Contacts, NEMA 7 Enclosure, 1/2 to 1 Input Shaft Ratio. For basic switch data see table 2 symbol A
2000-866 Ametek Gemco Rotary Limit Switch. Spur Gear Type, Two Independent Circuits, Cam / Switches. UL Listed Snap Action Switches with S.P.D.T. Contacts, NEMA 7 Enclosure, 1/3 to 1 Input Shaft Ratio. For basic switch data see table 2 symbol A
2000-867 Ametek Gemco Rotary Limit Switch. Spur Gear Type, Two Independent Circuits, Cam / Switches. UL Listed Snap Action Switches with S.P.D.T. Contacts, NEMA 7 Enclosure, 2 to 1 Input Shaft Ratio. For basic switch data see table 2 symbol A
2000-868 Ametek Gemco Rotary Limit Switch. Spur Gear Type, Two Independent Circuits, Cam / Switches. UL Listed Snap Action Switches with S.P.D.T. Contacts, NEMA 7 Enclosure, 3 to 1 Input Shaft Ratio. For basic switch data see table 2 symbol A
2000-89B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
5 to 1 Ratio Gear Ratio, the cam block rotates once every 5 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 1/16
Maximum switch setting @ 4 & 3/4 Turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(3LBS)
2000-8B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
100 to 1 Ratio Gear Ratio, the cam block rotates once every 100 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 3/4
Maximum switch setting @ 94 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(3LBS)
2000-90B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
10 to 1 Ratio Gear Ratio, the cam block rotates once every 10 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 12 Fibralloy Enclosure
Turns required to reset switch 1/16th
Maximum switch setting @ 9.5 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-91B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
20 to 1 Ratio Gear Ratio, the cam block rotates once every 20 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 1/8th
Maximum switch setting @ 19 & 1/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-92B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
30 to 1 Ratio Gear Ratio, the cam block rotates once every 30 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 1/4
Maximum switch setting @ 28 & 1/2
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-93B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
40 to 1 Ratio Gear Ratio, the cam block rotates once every 40 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 1/2
Maximum switch setting @ 38
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-94B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
50 to 1 Ratio Gear Ratio, the cam block rotates once every 50 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 1/2
Maximum switch setting @ 47
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-95B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
60 to 1 Ratio Gear Ratio, the cam block rotates once every 60 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 12 Rated Enclosure
Turns required to reset switch 1/2
Maximum switch setting @ 57 & 1/2 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-96B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
80 to 1 Ratio Gear Ratio, the cam block rotates once every 80 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 1 & 12 Enclosure
Turns required to reset switch 1/2
Maximum switch setting @ 76 & 3/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-97B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
100 to 1 Ratio Gear Ratio, the cam block rotates once every 100 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals 04537001
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 12 Rated Enclosure
Turns required to reset switch 1 & 1/2
Maximum switch setting @ 56 & 1/4 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(4LBS)
2000-98B Ametek Gemco Series 2000 Worm Gear Type Rotary Limit Switch. 4 Independent Standard Dwell Cams / Circuits / Switches, UL Listed Snap Action S.P.D.T. Switches, NEMA 1 & 12 Fibralloy Enclosure, 250 to 1 Gear Ratio. 1/2 Inch input shaft with woodruff key. Maximum RPM 1000. Maximum operating temperature 180 degree F. (6LBS)
2000-99B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
500 to 1 Ratio Gear Ratio, the cam block rotates once every 500 turns of the main shaft
4 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 12 Enclosure
Turns required to reset switch 7
Maximum switch setting @ 460
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2000-9B Ametek Gemco Rotary Limit Switch
Series 2000 Worm Gear Type with Bronze Gears & Steel Cams
5 to 1 Ratio Gear Ratio, the cam block rotates once every 5 turns of the main shaft
2 Independently Adjustable Switches/ Circuits / Cams
Single Pole Double Throw U.L. Listed Precision Snap Action Switches which can be wired for normally open or closed circuits. 4 Screw Terminals
Standard Cams allow switch contacts to be opened for 25 or 335 Degrees. Other cam dwells are available
NEMA 4 Rated Cast Aluminum Enclosure, Watertight
Turns required to reset switch 1/16
Maximum switch setting @ 4 & 1/2 turns
Up to 1000 RPM Clock Wise or CCW
1/2 Inch Diameter Input Shaft Extends 1 & 1/2 Inch from the Enclosure, Includes a Woodruff Keyway & # 404 Key
Maximum Operating Temperature 180 Degrees F
1/2 -14 American Standard Pipe Thread Entrance
(6LBS)
2006-1435 Ametek Gemco Geared Rotary Limit Switch. 2006 Series. 60 to 1 Gear Ratio. NEMA 4 Enclosure. Left Hand Shaft Extension. 2 Circuit with SPDT Switches. Gemco compatible resolver
2006-1464 Ametek Gemco Series 2000 Type K Rotary Limit Switch, 2 Independent Circuits / Cams / Switches, NEMA 4 Enclosure, Left Hand Shaft Extension, 20 to 1 Gear Ratio, S.P.D.T. Single Pole Double Throw Precision Snap Switches, with Potentiometer 4/7
2006-1483 Ametek Gemco Series 2000 Type K Rotary Limit Switch, 2 Circuit, NEMA 4 Enclosure, Left Hand Shaft Extension, 80 to 1 Gear Ratio, Both Snap Switches are Double Pole Double Throw. Special Long Dwell 45 Degree Cams (5LBS)
2006-1484 Ametek Gemco Series 2000 Type K Rotary Limit Switch, 2 Circuit, NEMA 4 Enclosure, Left Hand Shaft Extension, 40 to 1 Gear Ratio, Both Snap Switches are Double Pole Double Throw. Special Long Dwell 45 Degree Cams (5LBS)
2006-1505 Ametek Gemco Geared Rotary Limit Switch
Like 2006-402-L-30-A
1505 = Specially Engineered Product, Unit to include a mounted 500 Ohm Potentiometer that has a 1 to 1 ratio with the cam block
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
30 = 30 to 1 Gear Ratio. Cam Block turns once every 30 turns of the main shaft
A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
3/8 Shaft Turn required to reset the switch
Maximum switch setting at 26 turns, minimum at 1 turn
(4LBS)
2006-1543 Ametek Gemco Series 2000 Type K Rotary Limit Switch, 2 Independent Air Valves, NEMA 4 Enclosure, Left Hand Shaft Extension, 357 to 1 Gear Ratio (6LBS)
2006-1547 Ametek Gemco Series 2000 Type K Rotary Limit Switch, 4 Independent Circuits / Cams / Switches, NEMA 4 Enclosure, Left Hand Shaft Extension, 120 to 1 Gear Ratio, Qty 2, S.P.D.T. Single Pole Double Throw Precision Snap Switches & Qty 2, D.P.D.T. Double Pole Double Throw Precision Snap Switches. Qty. 2, 180 Degree Dwell Cams & Qty. 2, Standard Dwell Cams (6LBS)
2006-1549 Ametek Gemco Geared Rotary Limit Switch
2006 Type ''K''
1549 = Specially Engineered Product
Qty. 2, Circuit with SPDT Switches
50 to 1 Gear Ratio
NEMA 4 Enclosure, LH Shaft Output
10K Pot with a 1 to 1 Ratio
2006-2003 Ametek Gemco Type K Rotary Limit Switch, 2 Independent Circuits / Cams / Switches. NEMA 4 Enclosure, Left Hand Shaft Extension, 15 to 1 Gear Ratio, Snap Action Switches are Single Pole Double Throw. This specially engineered unit also includes an External Gear Reducer with a Right Angle Shaft Extension and Mounting Base Plate. 40 to 1 Gear Ratio # SD0315400 (8LBS)
2006-2015 Ametek Gemco Geared Rotary Limit Switch
Same as 2006-402-L-30-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
30 = 30 to 1 Gear Ratio. Cam Block turns once every 30 turns of the main shaft
A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
3/8 Shaft Turn required to reset the switch
Maximum switch setting at 26 turns, minimum at 1 turn
C-H 10316H-4557-1
(4LBS)
2006-2017 Ametek Gemco Series 2000 Type K Rotary Limit Switch, 2006-404-L-60-A, 4 Circuit, NEMA 4 Enclosure, Left Hand Shaft Extension, 60 to 1 Ratio, All Switches Single Pole Double Throw. (SPDT)
2006-402-L-10-A Ametek Gemco Geared Rotary Limit Switch
2006-402-L-10-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
10 = 10 to 1 Gear Ratio. Cam Block turns once every 10 turns of the main shaft
A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
1/8 Turns required to reset the switch
Maximum switch setting at 8 & 1/2 turns, minimum at 1/4 turn
C-H 10316H-1016-1
(4LBS)
2006-402-L-10-C Ametek Gemco Geared Rotary Limit Switch
2006-402-L-10-C
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
10 = 10 to 1 Gear Ratio. Cam Block turns once every 10 turns of the main shaft
C = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO
1/8 Turns required to reset the switch
Maximum switch setting at 8 & 1/2 turns, minimum at 1/4 turn
C-H 10316H-1016-1
(4LBS)
2006-402-L-1080-A Ametek Gemco Geared Rotary Limit Switch
2006-402-L-1080-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
1080 = 1080 to 1 Gear Ratio. Cam Block turns once every 1080 turns of the main shaft
A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
13.5 Turns required to reset the switch
Maximum switch setting at 954 turns, minimum at 36
C-H 10316H-169-1
(5LBS)
2006-402-L-1080-C Ametek Gemco Geared Rotary Limit Switch
2006-402-L-1080-C
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
1080 = 1080 to 1 Gear Ratio. Cam Block turns once every 1080 turns of the main shaft
C = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-4-B-A-DO
13.5 Turns required to reset the switch
Maximum switch setting at 954 turns, minimum at 36
C-H
(5LBS)
2006-402-L-120-A Ametek Gemco Geared Rotary Limit Switch
2006-402-L-120-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Watertight Die Cast Enclosure
02 = 2 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway
120 = 120 to 1 Gear Ratio. Cam Block turns once every 120 turns of the main shaft
A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch 1950-1-B-A-DO
1 & 1/2 Turns required to reset the switch
Maximum switch setting at 108 turns, minimum at 3 turn
C-H 10316H-155-1
(4LBS)
2006-402-L-120-C Ametek Gemco Geared Rotary Limit Switch
2006-402-L-120-C
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Watertight Die Cast Enclosure
02 = 2 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway
120 = 120 to 1 Gear Ratio. Cam Block turns once every 120 turns of the main shaft
C = Double Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch 1950-4-B-A-DO
1 & 1/2 Turns required to reset the switch
Maximum switch setting at 108 turns, minimum at 3 turn
(4LBS)
2006-402-L-20-A Ametek Gemco Geared Rotary Limit Switch
2006-402-L-20-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
20 = 20 to 1 Gear Ratio. Cam Block turns once every 20 turns of the main shaft
A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
1/4 Turns required to reset the switch
Maximum switch setting at 17 turns, minimum at 1/2 turn
C-H 10316H-1017-1
(4LBS)
2006-402-L-20-C Ametek Gemco Geared Rotary Limit Switch
2006-402-L-20-C
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
20 = 20 to 1 Gear Ratio. Cam Block turns once every 20 turns of the main shaft
C = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO
1/8 Turns required to reset the switch
Maximum switch setting at 8 & 1/2 turns, minimum at 1/4 turn
(4LBS)
2006-402-L-270-A Ametek Gemco Geared Rotary Limit Switch
2006-402-L-270-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
270 = 270 to 1 Gear Ratio. Cam Block turns once every 270 turns of the main shaft
A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
3.375 Shaft Turns required to reset the switch
Maximum switch setting at 236 turns, minimum at 6.75 turns
C-H 10316H-4599-1
(5LBS)
2006-402-L-30-A Ametek Gemco Geared Rotary Limit Switch
2006-402-L-30-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
30 = 30 to 1 Gear Ratio. Cam Block turns once every 30 turns of the main shaft
A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
3/8 Shaft Turn required to reset the switch
Maximum switch setting at 26 turns, minimum at 1 turn
C-H 10316H-4557-1
(4LBS)
2006-402-L-30-B Ametek Gemco Geared Rotary Limit Switch
2006-402-L-30-B
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
30 = 30 to 1 Gear Ratio. Cam Block turns once every 30 turns of the main shaft
B = One Double Pole Double Throw Snap Action Switch. Can be wired for either normally open or a closed circuit. 8 Screw Terminals per Switch # 1950-4-B-A-DO and One Single Pole Double Throw Snap Action Switch. Can be wired for either normally open or a closed circuit. 4 Screw Terminals per Switch # 1950-1-B-A-DO
3/8 Shaft Turn required to reset the switch
Maximum switch setting at 26 turns, minimum at 1 turn
(5LBS)
2006-402-L-30-C Ametek Gemco Geared Rotary Limit Switch
2006-402-L-30-C
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
30 = 30 to 1 Gear Ratio. Cam Block turns once every 30 turns of the main shaft
C = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO
3/8 Shaft Turn required to reset the switch
Maximum switch setting at 26 turns, minimum at 1 turn
(5LBS)
2006-402-L-357-A Ametek Gemco Geared Rotary Limit Switch
2006-402-L-357-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
357 = 357 to 1 Gear Ratio. Cam Block turns once every 357 turns of the main shaft
A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
4.46 Shaft Turns required to reset the switch
Maximum switch setting at 350 turns, minimum at 12 turns
C-H 10316H-167-1
(5LBS)
2006-402-L-357-C Ametek Gemco Geared Rotary Limit Switch
2006-402-L-357-C
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
357 = 357 to 1 Gear Ratio. Cam Block turns once every 357 turns of the main shaft
C = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO
4.46 Shaft Turns required to reset the switch
Maximum switch setting at 350 turns, minimum at 12 turns
(5LBS)
2006-402-L-40-A Ametek Gemco Geared Rotary Limit Switch
2006-402-L-40-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
40 = 40 to 1 Gear Ratio. Cam Block turns once every 40 turns of the main shaft
A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
1/2 Turns required to reset the switch
Maximum switch setting at 35 turns, minimum at 1 turn
C-H 10316H-157-1
(4LBS)
2006-402-L-40-B Ametek Gemco Geared Rotary Limit Switch
2006-402-L-40-B
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
40 = 40 to 1 Gear Ratio. Cam Block turns once every 40 turns of the main shaft
B = One Double Pole Double Throw Snap Action Switch. Can be wired for either normally open or a closed circuit. 8 Screw Terminals per Switch # 1950-4-B-A-DO and One Single Pole Double Throw Snap Action Switch. Can be wired for either normally open or a closed circuit. 4 Screw Terminals per Switch # 1950-1-B-A-DO
1/2 Turns required to reset the switch
Maximum switch setting at 35 turns, minimum at 1 turn
(5LBS)
2006-402-L-40-C Ametek Gemco Geared Rotary Limit Switch
2006-402-L-40-C
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
40 = 40 to 1 Gear Ratio. Cam Block turns once every 40 turns of the main shaft
C = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO
1/2 Turns required to reset the switch
Maximum switch setting at 35 turns, minimum at 1 turn
(5LBS)
2006-402-L-5-A Ametek Gemco Geared Rotary Limit Switch
2006-402-L-5-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
5 = 5 to 1 Gear Ratio. Cam Block turns once every 5 turns of the main shaft
A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
1/16 Turns required to reset the switch
Maximum switch setting at 4 turns, minimum at 1/8 turn
C-H 10316H-4556-1
(4LBS)
2006-402-L-5-B Ametek Gemco Geared Rotary Limit Switch
2006-402-L-5-B
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
5 = 5 to 1 Gear Ratio. Cam Block turns once every 5 turns of the main shaft
B = 1 Double Pole Double Throw Snap Action Switch. 1 Single Pole Double Throw Switch. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch
1/16 Turns required to reset the switch
Maximum switch setting at 4 turns, minimum at 1/8 turn
(4LBS)
2006-402-L-5-C Ametek Gemco Geared Rotary Limit Switch
2006-402-L-5-C
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
5 = 5 to 1 Gear Ratio. Cam Block turns once every 5 turns of the main shaft
C = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO
1/16 Turns required to reset the switch
Maximum switch setting at 4 turns, minimum at 1/8 turn
(4LBS)
2006-402-L-60-A Ametek Gemco Geared Rotary Limit Switch
2006-402-L-60-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Watertight Die Cast Enclosure
02 = 2 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway
60 = 60 to 1 Gear Ratio. Cam Block turns once every 60 turns of the main shaft
A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
3/4 Turns required to reset the switch
Maximum switch setting at 53 turns, minimum at 2 turns
C-H 10316H-156-1
(4LBS)
2006-402-L-60-C Ametek Gemco Geared Rotary Limit Switch
2006-402-L-60-C
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Watertight Die Cast Enclosure
02 = 2 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway
60 = 60 to 1 Gear Ratio. Cam Block turns once every 60 turns of the main shaft
C = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO
3/4 Turns required to reset the switch
Maximum switch setting at 53 turns, minimum at 2 turns
(4LBS)
2006-402-L-80-A Ametek Gemco Geared Rotary Limit Switch
2006-402-L-80-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Watertight Die Cast Enclosure
02 = 2 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway
80 = 80 to 1 Gear Ratio. Cam Block turns once every 80 turns of the main shaft
A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
1 Turn required to reset the switch
Maximum switch setting at 72 turns, minimum at 2 & 1/2 turns
C-H 10316H-4559-1
(4LBS)
2006-402-L-80-C Ametek Gemco Geared Rotary Limit Switch
2006-402-L-80-C
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Watertight Die Cast Enclosure
02 = 2 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway
80 = 80 to 1 Gear Ratio. Cam Block turns once every 80 turns of the main shaft
C= Double Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO
1 Turn required to reset the switch
Maximum switch setting at 72 turns, minimum at 2 & 1/2 turns
(4LBS)
2006-402-R-10-A Ametek Gemco Geared Rotary Limit Switch
2006-402-R-10-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
R = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
10 = 10 to 1 Gear Ratio. Cam Block turns once every 10 turns of the main shaft
A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
1/8 Turns required to reset the switch
Maximum switch setting at 8 & 1/2 turns, minimum at 1/4 turn
(4LBS)
2006-402-R-120-A Ametek Gemco Geared Rotary Limit Switch
2006-402-R-120-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
R = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
120 = 120 to 1 Gear Ratio. Cam Block turns once every 120 turns of the main shaft
A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
1/2 Turns required to reset the switch
Maximum switch setting at 108 turns, minimum at 3 turns
C-H 10316H-179-1
(4LBS)
2006-402-R-120-C Ametek Gemco Geared Rotary Limit Switch
2006-402-R-120-C
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
R = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
120 = 120 to 1 Gear Ratio. Cam Block turns once every 120 turns of the main shaft
C = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO
(5LBS)
2006-402-R-20-A Ametek Gemco Geared Rotary Limit Switch
2006-402-R-20-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Watertight Die Cast Enclosure
02 = 2 Independent Circuits / Switches / Cams
R = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway
20 = 20 to 1 Gear Ratio. Cam Block turns once every 10 turns of the main shaft
A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
(4LBS)
2006-402-R-270-A Ametek Gemco Geared Rotary Limit Switch
2006-402-R-270-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
R = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
270 = 270 to 1 Gear Ratio. Cam Block turns once every 270 turns of the main shaft
A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
3.375 Shaft Turns required to reset the switch
Maximum switch setting at 236 turns, minimum at 6.75 turns
C-H 10316H-4606-1
(5LBS)
2006-402-R-30-A Ametek Gemco Geared Rotary Limit Switch
2006-402-R-30-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
R = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
30 = 30 to 1 Gear Ratio. Cam Block turns once every 30 turns of the main shaft
A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
3/8 Shaft Turn required to reset the switch
Maximum switch setting at 26 turns, minimum at 1 turn
C-H 10316H-4561-1
(5LBS)
2006-402-R-357-A Ametek Gemco Geared Rotary Limit Switch
2006-402-R-357-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Watertight Die Cast Enclosure
02 = 2 Independent Circuits / Switches / Cams
R = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway
357 = 357 to 1 Gear Ratio. Cam Block turns once every 357 turns of the main shaft
R = 1950-1408 Switches
4.46 Turns to Reset
(4LBS)
2006-402-R-40-A Ametek Gemco Geared Rotary Limit Switch
2006-402-R-40-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
L = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
40 = 40 to 1 Gear Ratio. Cam Block turns once every 40 turns of the main shaft
A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
1/2 Turns required to reset the switch
Maximum switch setting at 35 turns, minimum at 1 turn
C-H 10316H-181-1
(4LBS)
2006-402-R-40-C Ametek Gemco Geared Rotary Limit Switch
2006-402-R-40-C
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Watertight Die Cast Enclosure
02 = 2 Independent Circuits / Switches / Cams
R = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway
40 = 40 to 1 Gear Ratio. Cam Block turns once every 40 turns of the main shaft
C = Double Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch
(4LBS)
2006-402-R-40-R Ametek Gemco Geared Rotary Limit Switch
2006-402-R-40-R
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Watertight Die Cast Enclosure
02 = 2 Independent Circuits / Switches / Cams
R = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway
40 = 40 to 1 Gear Ratio. Cam Block turns once every 40 turns of the main shaft
R = 1950-1408 Slow Make Slow Break Switches, Single Pole Double Throw S.P.D.T., Can be wired for Normally Open or Closed Circuits, 4 Screw Terminals per Switch
1/2 Turn to Reset Switch
(4LBS)
2006-402-R-5-A Ametek Gemco Geared Rotary Limit Switch
2006-402-R-5-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
R = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
5 = 5 to 1 Gear Ratio. Cam Block turns once every 5 turns of the main shaft
A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
C-H 10316H-1018-1
(4LBS)
2006-402-R-5-C Ametek Gemco Geared Rotary Limit Switch
2006-402-R-5-C
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
02 = 2 Independent Circuits / Switches / Cams
R = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
5 = 5 to 1 Gear Ratio. Cam Block turns once every 5 turns of the main shaft
C = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO
(5LBS)
2006-402-R-60-A Ametek Gemco Geared Rotary Limit Switch
2006-402-R-60-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Watertight Die Cast Enclosure
02 = 2 Independent Circuits / Switches / Cams
R = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway
60 = 60 to 1 Gear Ratio. Cam Block turns once every 60 turns of the main shaft
A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
3/4 Turns required to reset the switch
Maximum switch setting at 53 turns, minimum at 2 turns
C-H 10316H-180-1
(5LBS)
2006-402-R-80-A Ametek Gemco Geared Rotary Limit Switch
2006-402-R-80-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Watertight Die Cast Enclosure
02 = 2 Independent Circuits / Switches / Cams
R = Right Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway
80 = 80 to 1 Gear Ratio. Cam Block turns once every 80 turns of the main shaft
A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
1 Turns required to reset the switch
Maximum switch setting at 72 turns, minimum at 2 & 1/2 turns
C-H 10316H-4563-1
(5LBS)
2006-404-L-10-A Ametek Gemco Geared Rotary Limit Switch
2006-404-L-10-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Watertight Die Cast Enclosure
04 = 4 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway
10 = 10 to 1 Gear Ratio. Cam Block turns once every 10 turns of the main shaft
A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-D0
1/8 Turn to Reset Switch
C-H 10316H-1026-1
(6LBS)
2006-404-L-10-E Ametek Gemco Geared Rotary Limit Switch
2006-404-L-10-E
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
04 = 4 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
10 = 10 to 1 Gear Ratio. Cam Block turns once every 10 turns of the main shaft
E = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO
1/8 Turn of Main Shaft is required to Reset the Switch
Maximum Switch Setting is at 8 & 1/2 Turns, Minimum is at 1/4 Turn
(6LBS)
2006-404-L-1080-A Ametek Gemco Geared Rotary Limit Switch
2006-404-L-1080-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
04 = 4 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
357 = 1080 to 1 Gear Ratio. Cam Block turns once every 1080 turns of the main shaft
A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
C-H 10316H-173-1
(6LBS)
2006-404-L-120-A Ametek Gemco Geared Rotary Limit Switch
2006-404-L-120-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
04 = 4 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
120 = 120 to 1 Gear Ratio. Cam Block turns once every 120 turns of the main shaft
A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
1 & 1/2 Turns required to reset the switch
Maximum switch setting at 108 turns, minimum 3 turns
C-H 10316H-158-1
(6LBS)
2006-404-L-120-C Ametek Gemco Series 2000 Type K Rotary Limit Switch, 4 Independent Circuits / Cams / Switches, NEMA 4 Enclosure, Left Hand Shaft Extension, 120 to 1 Gear Ratio, Qty 2, S.P.D.T. Single Pole Double Throw Precision Snap Switches & Qty 2, D.P.D.T. Double Pole Double Throw Precision Snap Switches. (6LBS)
2006-404-L-120-E Ametek Gemco Series 2000 Type K Rotary Limit Switch, 4 Independent Circuits / Cams / Switches, NEMA 4 Enclosure, Left Hand Shaft Extension, 120 to 1 Gear Ratio, D.P.D.T. Double Pole Double Throw Precision Snap Switches (6LBS)
2006-404-L-20-A Ametek Gemco Geared Rotary Limit Switch
2006-404-L-20-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Watertight Die Cast Enclosure
04 = 4 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway
20 = 20 to 1 Gear Ratio. Cam Block turns once every 20 turns of the main shaft
A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-D0
1/4 Turn to Reset Switch
C-H 10316H-1027-1
(6LBS)
2006-404-L-20-C Ametek Gemco Series 2000 Type K Rotary Limit Switch, 4 Independent Circuits / Cams / Switches, NEMA 4 Enclosure, Left Hand Shaft Extension, 20 to 1 Gear Ratio, Two D.P.D.T. Double Pole Double Throw Precision Snap Switches & Two S.P.D.T. Single Pole Double Throw Precision Snap Switches (6LBS)
2006-404-L-20-E Ametek Gemco Geared Rotary Limit Switch
2006-404-L-20-E
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
04 = 4 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
20 = 20 to 1 Gear Ratio. Cam Block turns once every 20 turns of the main shaft
E = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO
1/4 Turn of Main Shaft is required to Reset the Switch
Maximum Switch Setting is at 17 Turns, Minimum is at 1/2 Turn
(6LBS)
2006-404-L-270-A Ametek Gemco Geared Rotary Limit Switch
2006-404-L-270-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
04 = 4 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
270 = 270 to 1 Gear Ratio. Cam Block turns once every 270 turns of the main shaft
A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
C-H 10316H-4600-1
(6LBS)
2006-404-L-270-C Ametek Gemco Series 2000 Type K Rotary Limit Switch, 4 Independent Circuits / Cams / Switches, NEMA 4 Enclosure, Left Hand Shaft Extension, 270 to 1 Gear Ratio, Two D.P.D.T. Double Pole Double Throw Precision Snap Switches & Two S.P.D.T. Single Pole Double Throw Precision Snap Switches (6LBS)
2006-404-L-30-A Ametek Gemco Geared Rotary Limit Switch
2006-404-L-30-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Watertight Die Cast Enclosure
04 = 4 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway
30 = 30 to 1 Gear Ratio. Cam Block turns once every 30 turns of the main shaft
A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
3/8 turn to Reset Switch
C-H 10316H-4569-1
(6LBS)
2006-404-L-30-E Ametek Gemco Geared Rotary Limit Switch
2006-404-L-30-E
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
04 = 4 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
30 = 30 to 1 Gear Ratio. Cam Block turns once every 30 turns of the main shaft
E = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO
3/8 Turn of Main Shaft is required to Reset the Switch
Maximum Switch Setting is at 26 Turns, Minimum is at 1 Turn
(6LBS)
2006-404-L-357-A Ametek Gemco Geared Rotary Limit Switch
2006-404-L-357-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
04 = 4 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
357 = 357 to 1 Gear Ratio. Cam Block turns once every 270 turns of the main shaft
A = Single Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
C-H 10316H-175-1
(6LBS)
2006-404-L-357-E Ametek Gemco Series 2000 Type K Rotary Limit Switch, 4 Independent Circuits / Cams / Switches, NEMA 4 Enclosure, Left Hand Shaft Extension, 357 to 1 Gear Ratio, D.P.D.T. Double Pole Double Throw Precision Snap Switches (6LBS)
2006-404-L-40-A Ametek Gemco Geared Rotary Limit Switch
2006-404-L-40-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Watertight Die Cast Enclosure
04 = 4 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway
40 = 40 to 1 Gear Ratio. Cam Block turns once every 40 turns of the main shaft
A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch
Switch # 1950-1-B-A-D0
Maximum switch setting at 35 turns, minimum at 1 turn
1/2 Turn to Reset Switch
C-H 10316H-160-1
(6LBS)
2006-404-L-40-E Ametek Gemco Geared Rotary Limit Switch
2006-404-L-40-E
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
04 = 4 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
40 = 40 to 1 Gear Ratio. Cam Block turns once every 40 turns of the main shaft
E = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO
1/2 Turn of Main Shaft is required to Reset the Switch
Maximum Switch Setting is at 35 Turns, Minimum is at 1 Turn
(6LBS)
2006-404-L-5-A Ametek Gemco Geared Rotary Limit Switch
2006-404-L-5-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Watertight Die Cast Enclosure
04 = 4 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway
5 = 5 to 1 Gear Ratio. Cam Block turns once every 5 turns of the main shaft
A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
1/16 Turn to Reset Switch
Maximum switch setting at 4 turns, minimum at 1/8th turn
C-H 10316H-4568-1
(6LBS)
2006-404-L-5-C Ametek Gemco Series 2000 Type K Rotary Limit Switch, 4 Independent Circuits / Cams / Switches, NEMA 4 Enclosure, Left Hand Shaft Extension, 5 to 1 Gear Ratio, Two D.P.D.T. Double Pole Double Throw Precision Snap Switches & Two S.P.D.T. Single Pole Double Throw Precision Snap Switches (6LBS)
2006-404-L-5-E Ametek Gemco Series 2000 Type K Rotary Limit Switch, 4 Independent Circuits / Cams / Switches, NEMA 4 Enclosure, Left Hand Shaft Extension, 5 to 1 Gear Ratio, D.P.D.T. Double Pole Double Throw Precision Snap Switches (6LBS)
2006-404-L-60-A Ametek Gemco Geared Rotary Limit Switch
2006-404-L-60-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Watertight Die Cast Enclosure
04 = 4 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway
60 = 60 to 1 Gear Ratio. Cam Block turns once every 60 turns of the main shaft
A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
3/4 Turn to Reset Switch
C-H 10316H-159-1
(5LBS)
2006-404-L-60-C Ametek Gemco Series 2000 Type K Rotary Limit Switch, 4 Independent Circuits / Cams / Switches, NEMA 4 Enclosure, Left Hand Shaft Extension, 60 to 1 Gear Ratio, Two S.P.D.T. Single Pole Double Throw Precision Snap Switches & Two D.P.D.T. Double Pole Double Throw Switches (5LBS)
2006-404-L-60-D Ametek Gemco Series 2000 Type K Rotary Limit Switch, 4 Independent Circuits / Cams / Switches, NEMA 4 Enclosure, Left Hand Shaft Extension, 60 to 1 Gear Ratio, Three D.P.D.T. Double Pole Double Throw Precision Snap Switches & One S.P.D.T. Single Pole Double Throw Precision Snap Switches (6LBS)
2006-404-L-60-E Ametek Gemco Geared Rotary Limit Switch
2006-404-L-60-E
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
04 = 4 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
60 = 60 to 1 Gear Ratio. Cam Block turns once every 60 turns of the main shaft
E = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO
3/4 Turn of Main Shaft is required to Reset the Switch
Maximum Switch Setting is at 53 Turns, Minimum is at 2 Turns
(6LBS)
2006-404-L-80-A Ametek Gemco Geared Rotary Limit Switch
2006-404-L-80-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Watertight Die Cast Enclosure
04 = 4 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway
80 = 80 to 1 Gear Ratio. Cam Block turns once every 80 turns of the main shaft
A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch
Switch # 1950-1-B-A-DO
Maximum switch setting at 72 turns, minimum at 2 & 1/2 turns
1 Turn to Reset Switch
C-H 10316H-4571-1
(6LBS)
2006-404-L-80-E Ametek Gemco Geared Rotary Limit Switch
2006-404-L-80-E
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Die Cast Enclosure, Watertight
04 = 4 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with Woodruff Keyway & # 404 Woodruff Key
80 = 80 to 1 Gear Ratio. Cam Block turns once every 80 turns of the main shaft
E = Double Pole Double Throw Snap Action Switches. Can be wired for either normally open or closed circuits. 8 Screw Terminals per Switch # 1950-4-B-A-DO
1 Turn of Main Shaft is required to Reset the Switch
Maximum Switch Setting is at 72 Turns, Minimum is at 2 & 1/2 Turns
(6LBS)
2006-404-L40-A Ametek Gemco Geared Rotary Limit Switch
2006-404-L-40-A
2006 = Type ''K'' Rotary Limit Switch
4 = NEMA 4 Rated Watertight Die Cast Enclosure
04 = 4 Independent Circuits / Switches / Cams
L = Left Hand Shaft Extension from the Enclosure. 1/2 Dia. x 1 & 1/2 Inch Extension with # 3 Woodruff Key & Keyway
40 = 40 to 1 Gear Ratio. Cam Block turns once every 40 turns of the main shaft
A = Single Pole Double Throw Switches. Can be wired for either normally open or closed circuits. 4 Screw Terminals per Switch # 1950-1-B-A-DO
1/2 Turn to Reset Switch
(6LBS)
2020-1 Ametek Gemco Rotary Limit Switch. Now Obsolete, 1996. Series 2020 Traveling Nut Limit Switch. Qty. 2, 1950-1-B-A-DO S.P.D.T. Precision Snap Switches, Switches can be adjusted between 5 and 100 revolutions of the input shaft. 1/2 inch diameter input shaft. 10 AMP., 600 Volt Maximum
2110-1404 Ametek Gemco Shut Height Monitor Series 2110
LDT Board
Digital Output / Sourcing
Specially Engineered Brackets C0966900
1/4
2110-L1-K0-D0-A0-N0 Ametek Gemco Shut Height Monitor
Model 2110-L1-K0-D0-A0-N0
2 Channel Analog Output
L1 = 952 Digital Input Board
K0 = Without Relay Board
D0 = Without Digital Output Board
A0 = Without Analog Board
N0 = No Enclosure Supplied. NEMA 4 & 12 are available
2110-L1-K0-D0-A1-N0 Ametek Gemco Shut Height Monitor
Model 2110-L1-K0-D0-A1-N0
2 Channel Analog Output
L1 = 952 Digital Input Board
K0 = Without Relay Board
D0 = Without Digital Output Board
A1 = Programmable for Voltage or Current
N0 = No Enclosure Supplied. NEMA 4 & 12 are available
2110-R1-K0-D0-A0-N0 Ametek Gemco Shut Height Monitor
Model 2110-R1-K0-D0-A0-N0
2 Channel Analog Output
R1 = Resolver Board Input
K0 = Without Relay Board
D0 = Without Digital Output Board
A0 = Without Analog Board
N0 = No Enclosure Supplied. NEMA 4 & 12 are available
2110-R1-K0-D0-A1-N0 Ametek Gemco Shut Height Monitor
Model 2110-R1-K0-D0-A1-N0
R1 = Resolver Board Input
K0 = Without Relay Board
D0 = Without Digital Output Board
A1 = Two Channel Analog Output, Programmable for Voltage or Current
N0 = No Enclosure Supplied. NEMA 4 & 12 are available
2110-R1-K0-D2-A0-N4 Ametek Gemco Shut Height Monitor
Model 2110-R1-K1-D2-A0-N4
R1 = Resolver Board Input
K0 = Without Relay Board
D2 = Sourcing Digital Output Board
A0 = Without Analog Board
N4 = NEMA 4 Enclosure
2110-R1-K0-D2-A1-N0 Ametek Gemco Shut Height Monitor
Model 2110-R1-K0-D2-A1-N4
R1 = Resolver Board Input
K0 = Without Relay Board
D2 = Sourcing Digital Output Board
A1 = Two Channel Analog Output Programmable for Voltage or Current
N4 = NEMA 4 Rated Enclosure
2110-R1-K0-D3-A0-N0 Ametek Gemco Shut Height Monitor
Model 2110-R1-K0-D3-A0-N0
2110 - Shut Height Monitor
R1 = Resolver Board Input
K0 = Without Relay Board
D3 = TTL Digital Output Board
A0 = Without Analog Board
N0 = No Enclosure Supplied. NEMA 4 & 12 are available
2110-R1-K1-D0-A0-N0 Ametek Gemco Shut Height Monitor
Model 2110-R1-K1-D2-A0-N0
R1 = Resolver Board Input
K1 = With Relay Board
D0 = Without Digital Output Board
A0 = Without Analog Board
N0 = No Enclosure
2110-R1-K1-D0-A0-N4 Ametek Gemco Shut Height Monitor
Model 2110-R1-K1-D2-A0-N4
R1 = Resolver Board Input
K1 = With Relay Board
D0 = Without Digital Output Board
A0 = Without Analog Board
N4 = NEMA 4 Enclosure
2110-V1-K0-D0-A0-N0 Ametek Gemco Shut Height Monitor
Model 2110-V1-K0-D0-A0-N0
2 Channel Analog Output
V1 = LDT Board Input
K0 = Without Relay Board
D0 = Without Digital Output Board
A0 = Without Analog Board
N0 = No Enclosure Supplied. NEMA 4 & 12 are available
2110-V1-K0-D0-A0-N12 Ametek Gemco Shut Height Monitor
Model 2110-V1-K0-D0-A0-N12
2 Channel Analog Output
V1 = LDT Board Input
K0 = Without Relay Board
D0 = Without Digital Output Board
A0 = Without Analog Board
N12 = NEMA 12 Rated Enclosure
2110-V1-K1-D0-A0-N0 Ametek Gemco Shut Height Monitor
Model 2110-V1-K1-D0-A0-N0
2 Channel Analog Output
V1 = LDT Board Input
K1 = With Relay Board
D0 = Without Digital Output Board
A0 = Without Analog Board
N0 = No Enclosure Supplied. NEMA 4 & 12 are available
2110-V1-K1-D0-A0-N12 Ametek Gemco Shut Height Monitor
Model 2110-V1-K1-D0-A0-N12
V1 = LDT Board Input
K1= With Relay Board, 2 Form C Relays
D0 = Without Digital Output Board
A0 = Without Analog Board
N12 = NEMA 12 Rated Enclosure
2120-L1-K0-D0-A0-N0 Ametek Gemco Series 2120 PLC Interface Module model AME-2120-L1-K0-D0-A0-N0 for accurate, absolute position sensing Standard RS232/485 Communication Port
L1 = 952 Digital Input Board
K0 = Without Relay Board
D0 = Without Digital Output Board
A0 = Without Analog Board
N0 = No enclosure is to be supplied
2120-L1-K0-D1-A0-N0 Ametek Gemco Series 2120 PLC Interface Module model 2120-L1-K0-D1-A0-N0 for accurate, absolute position sensing Standard RS232/485 Communication Port
L1 = 952 Digital Input Board
K0 = Without Relay Board
D1 = ''Sinking'' Digital Output Type
A0 = Without Analog Board
N0 = No enclosure is to be supplied
2120-R1-K0-D0-A0-N0 Ametek Gemco Series 2120 PLC Interface Module model 2120-R1-K0-D0-A1-N0 for accurate, absolute position sensing. Standard RS232/485 Communication Port
R1 = Resolver Input
K0 = Without Relay Board
D0 = Without Digital Output Board
A0 = Without Analog Board
N0 = No enclosure
2120-R1-K0-D0-A1-N0 Ametek Gemco Series 2120 PLC Interface Module model 2120-R1-K0-D0-A1-N0 for accurate, absolute position sensing. Standard RS232/485 Communication Port
R1 = Resolver Input
K0 = Without Relay Board
D0 = Without Digital Output Board
A1 = Two Channel Analog Output Programmable for Voltage or Current
N0 = No enclosure
2120-R1-K0-D0-A1-N4 Ametek Gemco Series 2120 PLC Interface Module model 2120-R1-K0-D0-A1-N4 for accurate, absolute position sensing. Standard RS232/485 Communication Port
R1 = Resolver Input
K0 = Without Relay Board
D0 = Without Digital Output Board
A1 = Two Channel Analog Output Programmable for Voltage or Current
N4 = NEMA 4 Enclosure
2120-R1-K0-D1-A0-N0 Ametek Gemco Series 2120 PLC Interface Module model 2120-R1-K0-D1-A0-N0 for accurate, absolute position sensing Standard RS232/485 Communication Port
R1 = Resolver Board Input
K0 = Without Relay Board
D1 = ''Sinking'' Digital Output Type
A0 = Without Analog Board
N0 = No enclosure is to be supplied
2120-R1-K0-D1-A0-N12 Ametek Gemco Series 2120 PLC Interface Module model 2120-R1-K0-D1-A0-N12 for accurate, absolute position sensing Standard RS232/485 Communication Port
R1 = Resolver Board Input
K0 = Without Relay Board
D1 = ''Sinking'' Digital Output Type
A0 = Without Analog Board
N12 = NEMA 12 Rated Enclosure
2120-R1-K0-D1-A1-N0 Ametek Gemco Series 2120 PLC Interface Module model 2120-R1-K0-D1-A1-N0 for accurate, absolute position sensing. Standard RS232/485 Communication Port
R1 = Resolver Input
K0 = Without Relay Board
D1 = Sinking Digital Output ''E'',
A1 = Two Channel Analog Output Programmable for Voltage or Current
N0 = No enclosure
2120-R1-K0-D2-A0-N0 Ametek Gemco Series 2120 PLC Interface Module model 2120-R1-K0-D2-A0-N0 for accurate, absolute position sensing Standard RS232/485 Communication Port
R1 = Resolver Board Input
K0 = Without Relay Board
D2 = ''Sourcing'' Digital Output Type
A0 = Without Analog Board
N0 = No enclosure is to be supplied
2120-R1-K0-D2-A1-N4 Ametek Gemco Series 2120 PLC Interface Module model 2120-R1-K0-D2-A1-N4 for accurate, absolute position sensing. Standard RS232/485 Communication Port
R1 = Resolver Input
K0 = Without Relay Board
D2 = Digital Output Board Sourcing
A1= Two Channel Output Board Programmable for Voltage or Current
N4 = NEMA 4 Rated Enclosure
2120-R1-K0-D3-A0-N4 Ametek Gemco Series 2120 PLC Interface Module model 2120-R1-K0-D3-A0-N4 for accurate, absolute position sensing. Standard RS232/485 Communication Port.
R1 = Resolver Input
K0 = Without Relay Board
D3 = TTL Digital Output
A0= Without 2 Channel Analog Output Board
N4 = NEMA 4 Enclosure
2120-R1-K0-D3-A1-N0 Ametek Gemco Series 2120 PLC Interface Module model 2120-R1-K0-D3-A1-N0 for accurate, absolute position sensing. Standard RS232/485 Communication Port.
R1 = Resolver Input
K0 = Without Relay Board
D3 = TTL Digital Output
A1 = Programmable for voltage or Current
N0 = No Enclosure
23033 Ametek Gemco Pneumatic Air Releasing Cylinder on a 10 Inch Type ''S''Hydraulic Brake Assembly. The parking feature is spring set & pneumatically released.
23040 Ametek Gemco Piston Rod Assembly
2500-WINN-CD Ametek Gemco Software. Communication software, Windows based for programing the 2500 PLS. Programing can be done on your computer rather than on the PLS
2500C Ametek Gemco Main Controller Part #
Warranty 1 Year Parts & Labor F.O.B. Gemco
2500C-B-A-R-A-0A8D-X-12 Ametek Gemco Series 2500 Programmable Limit Switch.
2500C-B-A-R-A-0A8D-X-12
B = Blind Unit , Remote Operator Interface Required
A = General Software
R = Resolver Input
A = AC Input Power 100 to 240 Volt 50 or 60 Hz
0A8D = Qty. 8, DC Relays
X = No Options
12 = NEMA 12 Enclosure / Main Controller Only
Warranty 1 Year Parts & Labor F.O.B. Gemco
2500C-B-A-R-A-0A8D-X-12A Ametek Gemco Series 2500 Programmable Limit Switch.
2500C-B-A-R-A-0A8D-X-12A
B = Blind Unit , Remote Operator Interface Required
A = General Software
R = Resolver Input
A = AC Input Power 100 to 240 Volt 50 or 60 Hz
0A8D = Qty. 8, DC Relays
X = No Options
12A = NEMA 12 Enclosure with room for up to 2 Panel Mount Expansions
Warranty 1 Year Parts & Labor F.O.B. Gemco
2500C-F-A-R-A-0A6A-X-X Ametek Gemco Series 2500 Programmable Limit Switch.
2500C-F-A-R-A-0A6A-X-X
F = Stand Alone Unit, Face or Flange Mount
A = General Software
R = Resolver Input
A = AC Input Power 100 to 240 Volt 50 or 60 Hz
0A6A = Qty. 6, AC Solid State Relays Rated @ 3 AMPS
X = No Options
X = No Enclosure
Warranty 1 Year Parts & Labor F.O.B. Gemco
2500C-F-A-R-A-0A8A-B-12A Ametek Gemco Series 2500 Programmable Limit Switch
2500C-F-A-R-A-0A8A-B-12A
F = Stand Alone Unit, Face or Flange Mount
A = General Software
R = Resolver Input
A = AC Input Power 100 to 240 Volt 50 or 60 Hz
0A8A = Qty. 8, AC Solid State Relays Rated @ 3 AMPS
B = Brake Monitor
12A = NEMA 12 Enclosure with room for up to 2 panel mount expansions
Warranty: Limited 1 Year Warranty, Parts & Labor, F.O.B. Gemco
2500C-F-A-R-A-0A8A-X-X Ametek Gemco Series 2500 Programmable Limit Switch.
2500C-F-A-R-A-0A8A-X-X
F = Stand Alone Unit, Face or Flange Mount
A = General Software
R = Resolver Input
A = AC Input Power 100 to 240 Volt 50 or 60 Hz
0A8A = Qty. 8, AC Solid State Relays Rated @ 3 AMPS
X = No Options
X = No Enclosure
Warranty 1 Year Parts & Labor F.O.B. Gemco
2500C-F-A-R-A-0A8D-X-X Ametek Gemco Series 2500 Programmable Limit Switch
2500C-F-A-R-A-0A8D-X-X
F = Stand Alone Unit, Face or Flange Mount
A = General Software
R = Resolver Input
A = AC Input Power 100 to 240 Volt 50 or 60 Hz
0A8D = Qty. 8, DC Solid State Relays, Rated @ 3 AMPS
X = No Options
X = No Enclosure
Warranty 1 Year Parts & Labor F.O.B. Gemco
2500C-F-A-R-A-0A8M-X-12A Ametek Gemco Series 2500 Programmable Limit Switch
2500C-F-A-R-A-0A8M-X-12A
F = Stand Alone Unit, Face or Flange Mount
A = General Software
R = Resolver Input
A = AC Input Power 100 to 240 Volt 50 or 60 Hz
0A8D = Qty. 8, DC Mechanical Relays Rated @ 8 AMPS. (for this option all relays must be mechanical)
X = No Options
12A = NEMA 12 Enclosure with Room for 2 Panel Mount Expansions
Warranty 1 Year Parts & Labor F.O.B. Gemco
2500C-F-A-R-A-0A8M-X-X Ametek Gemco Series 2500 Programmable Limit Switch
2500C-F-A-R-A-0A8M-X-X
F = Stand Alone Unit, Face or Flange Mount
A = General Software
R = Resolver Input
A = AC Input Power 100 to 240 Volt 50 or 60 Hz
0A8D = Qty. 8, DC Mechanical Relays Rated @ 8 AMPS. (for this option all relays must be mechanical)
X = No Options
X = No Enclosure
Warranty 1 Year Parts & Labor F.O.B. Gemco
2500C-F-A-R-A-4A4D-X-X Ametek Gemco Series 2500 Programmable Limit Switch
2500C-F-A-R-A-4A4D-X-X
F = Stand Alone Unit, Face or Flange Mount
A = General Software
R = Resolver Input
A = AC Input Power 100 to 240 Volt 50 or 60 Hz
4A4D = Qty. 4, AC Solid state Relays & Qty. 4, DC Solid State Relays, Both Rated @ 3 AMPS
X = No Options
X = No Enclosure
1 Year Limited Warranty, 1 Year Parts & Labor F.O.B. Gemco
2500C-F-A-R-A-8A0D-X-12 Ametek Gemco Series 2500 Programmable Limit Switch
2500C-F-A-R-A-8A0D-X-12
F = Stand Alone Unit, Face or Flange Mount
A = General Software
R = Resolver Input
A = AC Input Power 100 to 240 Volt 50 or 60 Hz
8A0D = Qty. 8, AC Solid State Relays Rated @ 3 AMPS
X = No Brake Monitoring Option
12 = NEMA 12 Enclosure for Main controller Only. No expansion modules
Warranty: Limited 1 Year Warranty, Parts & Labor, F.O.B. Gemco
2500C-F-A-R-A-8A0D-X-X Ametek Gemco Series 2500 Programmable Limit Switch
2500C-F-A-R-A-8A0D-X-X
F = Stand Alone Unit, Face or Flange Mount
A = General Software
R = Resolver Input
A = AC Input Power 100 to 240 Volt 50 or 60 Hz
8A0D = Qty. 8, AC Solid State Relays, Rated @ 3 AMPS
X = No Options
X = No Enclosure
Warranty 1 Year Parts & Labor F.O.B. Gemco
2500E Ametek Gemco Expansion Module
2500E-A-0A8D-X Ametek Gemco Series 2500 Expansion Module 2500E-A-08D-A
A = AC Input Power 100 to 240 Volt, 50 / 60 Hz.
0A8D = Qty. 8, DC Relays
X = No Options
Warranty 1 Year Parts & Labor F.O.B. Gemco
2500E-A-8A0D-X Ametek Gemco Series 2500 Expansion Module
2500E-A-8A0D-X
A = AC Input Power 100 to 240 Volt, 50 / 60 Hz.
8A0D = Qty. 8, AC Relays
X =No Options.
Warranty: Limited 1 Year Warranty, Parts & Labor, F.O.B. Gemco
2500R-X Ametek Gemco Remote Operator Interface. 2500 Series
Warranty 1 Year Parts & Labor F.O.B. Gemco
279B97H02 Westinghouse Solenoid Assembly. See E005055 on a CB-35 5.5 Inch Diameter Brake, includes the Plunger & Solenoid Guides No coil. 3279B97H02 (5LBS)
3000-107 Ametek Gemco Gear Reducer, Right Angle, 30 to 1 Gear Ratio, R4
3000-150R Ametek Gemco Gear Reducer for a 1980 Series Rotary Limit Switch. 10 to 1 Ratio with a Straight / Parallel Drive . Right Hand. A main shaft must be purchased along with the gear reducer (6LBS)
3000-167L Ametek Gemco Gear Reducer. Straight Drive Gear Reducer with a 200 to 1 Ratio. Not available without a main shaft PM0188503
3000150R Ametek Gemco Gear Reducer for a 1980 Series Rotary Limit Switch. 10 to 1 Ratio with a Straight / Parallel Drive . A Main Shaft must be purchased with the gear reducer (6LBS)
3001-1 Ametek Gemco 1/2 Inch Sprocket Drive Coupling. Maximum torque rating 300 lb.-in. 1/2inch direct & sprocket drive 404 woodruff keyway & key. 50 turns of the adjusting screw will rotate coupling 360 degrees.
3001-101 Ametek Gemco Coupling. OBSOLETE SEE 3001-3 Adjustable Coupling for Presses. Provides means of changing the position between cam shaft and sprocket in 5 degree increments. 3/4 Inch Shaft Size. Sprockets are sold separately. Sprockets for this coupling work with # 25, #35 or # 50 Size Chain. Sprocket Teeth Available 30, 32, 35, or 36. If sold with a sprocket the sprocket comes mounted to the coupling.If sold less sprocket customer to supply sprocket mounting hardware, Qty.3, 1/4 -20 Bolts. Hardware must not extend more than 1/4 Inch past the sprocket (5LBS)
3001-2 Ametek Gemco 1/2 Inch Direct Drive Coupling. Maximum torque rating 300 lb.-in. 1/2inch direct & sprocket drive 404 woodruff keyway & key. 50 turns of the adjusting screw will rotate coupling 360 degrees. (1LB)
3001-3 Ametek Gemco Coupling. Adjustable Couplings changing timing between cam shaft and sprocket. Loosen Lock Screw and Rotate the Adjustment Screw. 50 Turns = 350 Degrees of rotation. Sprockets are sold separately. Sprockets for this coupling work with #35 Size Chain. Sprocket Teeth Available 30, 32, 35, or 36. If sold with a sprocket the sprocket comes mounted to the coupling.If sold less sprocket customer to supply sprocket mounting hardware, Qty.3, 1/4 -20 Bolts (5LBS)
3001-4 Ametek Gemco Coupling. Adjustable Coupling to facilitate easy Timing Adjustment between the 3/4 Inch Cam Shaft and the 3/4 Inch Drive Shaft. Loosen Lock Screw and Rotate the Adjustment Allen Screw. 50 Turns = 350 Degrees of rotation. Coupling has a 3/4 Inch Shaft Diameter Shaft which Extends 1.5 Inches from the Coupling, Shaft includes a # 606 Woodruff Key & Keyway. Coupling Bore Diameter 3/4 inch with Woodruff Keyway. Overall Length 3.125 Inches. Maximum Torque Capability 785 LB. / IN. (3LBS)
304 Stainless Steel Ametek Gemco Adder for a 304 stainless steel enclosure, cover, latches, camshaft, bearing flanges & flange bolts. The stainless steel enclosure is finished with a Gemco Gray Enamel Finish. It is not polished stainless steel.
439C394G01 Ametek Gemco Brake Shoe & Lining Complete see E019024
49974 Ametek Gemco Dual Air Reservoir (Old Wagner P/N AD49974) 23 LBS Net
6'' H 1 Ametek Gemco Hydraulic Brake System for Progressive / Controlled Stopping Torque. Torque range of 0 through 150 FT LBS. via Foot Pedal Pressure. System Type H with 1, 6 Inch Hydraulic Brake Assembly J23020. System includes Foot Pedal J008219 & Control Cylinder J017616, Fluid Reservoir / Bleeder, Bleeder Pushbutton J10808 , 100 FT Copper Tubing, Brake Fluid, Fittings, Gaskets and Armored Flexible Hoses. Specify whether 230 V DC, 115 V AC or a manual 1/4 turn valve for operation for the bleeder. Less a 6 X 3 Inch Brake Wheel
6'' H 2 Ametek Gemco 6 Inch Hydraulic Brake System, Qty. 2, Brake Assemblies, Control Cylinder, Pedal, Fluid Reservoir Bleeder, Tubing, Fluid and Fittings for a complete system, less brake wheels.
6'' HM 1 Ametek Gemco Brake System. HM Brake System (with parking) 6 X 3.25 Inch for Progressive / Controlled Stopping Torque and Parking. Torque range of 0 through 150 FT LBS. via Foot Pedal Pressure along with Spring Set Parking & Holding. Parking Brake Torque 35 FT LBS. Includes one 6 Inch Diameter Hydraulic Brake Assembly, HM Control Unit, Parking Brake Control Station with Signal Light, Foot Pedal & Control Cylinder, Fluid Reservoir / Bleeder, Bleeder Pushbutton, 150 FT Copper Tubing, Wagner 21B Super Heavy Duty Brake Fluid, Fittings, Gaskets and Armored Flexible Hoses. Specify whether 230 VDC or 115 VAC for the bleeder operation. A manually operated bleeder is also available. Less Brake Wheel (136LBS)
6'' HM 2 Ametek Gemco Brake System. HM Brake System with parking. 2, 6 X 3.25 Inch Brakes for Progressive / Controlled Stopping Torque and Parking. Torque range of 0 through 300 FT LBS. via Foot Pedal Pressure along with Spring Set Parking & Holding. Parking Brake Torque 70 FT LBS. Includes two 6 Inch Diameter Hydraulic Brake Assembly, HM Control Unit, Parking Brake Control Station with Signal Light, Foot Pedal & Control Cylinder, Fluid Reservoir / Bleeder, Bleeder Pushbutton, 150 FT Copper Tubing, Wagner 21B Super Heavy Duty Brake Fluid, Fittings, Gaskets and Armored Flexible Hoses. Specify whether 230 VDC or 115 VAC for the bleeder operation. A manually operated bleeder is also available. Less Brake Wheel
71211SN1MM00N0C111C8 Ametek Gemco Coil . DC 240 Volt Coil for new style FRB's (1LB)
76-1200 Ametek Gemco Roller Arm. Part of a 04537004
8''-H-1 Ametek Gemco 8 Inch Hydraulic Type H Brake System. Provides infinitely variable progressive brake application for smooth controlled braking. 0 to 200 LBS. / FT dynamic stopping torque. Includes Qty.1, 8 Inch Hydraulic Brake Assembly, Fluid Reservoir Bleeder, Pushbutton Switch with Enclosure for operating the bleeder check valve, Control Cylinder with Foot Pedal, 100 Feet of Hydraulic Tubing, Tube Fittings, Unions, Clamps, Bushings, Brackets, Gaskets, 4 Armored Flexible Hoses & Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703. 8 Inch Brake Weight 28 LBS. Overall Width 7 - 1/4 Inch , Height 12 - 9/16 Inch. Please specify whether the Fluid Reservoir Bleeder is to be AC DC or manually operated. A 8 X 3.25 Inch Brake Wheel is not included
8''-H-2 Ametek Gemco Hydraulic Brake System, Complete Type H Brake System. Infinitely Progressive Braking Torque, 0 to 400 Foot LBS via Foot Pedal Pressure based on a Maximum Pedal Pressure of 70 LBS. Includes Qty. 2, 8 Inch Hydraulic Brake Assemblies J002779, 230 Volt DC Fluid Reservoir Bleeder, Bleeder Pushbutton Station J10008, Control Cylinder J017616 with Pedal J008219, J73901 Installation Kit which includes, 250 Feet of Copper Tubing, Tube clamps, Tube Bushings, Tube Fittings, Tube Unions, Tube Tee, Qty.6, Armored Hose Kits J010797 & 1 Gallon of Wagner 21B Brake Fluid F9314 (189LBS) AME-80200013
8''-HM-1 Ametek Gemco 8 X 3.25 Inch Hydraulic Brake System Type HM for Progressive / Controlled Stopping Torque and Parking. Torque range of 0 through 200 FT LBS. via Foot Pedal Pressure along with Spring Set Parking & Holding. Parking Torque 50 FT LBS. Includes one 8 Inch Diameter Hydraulic Brake Assembly, HM Control Unit, Parking Brake Control station with Signal Light, Foot Pedal & Control Cylinder, Fluid Reservoir / Bleeder, Bleeder Pushbutton, 150 FT Copper Hydraulic Tubing, Wagner 21B Super Heavy Duty Brake Fluid, Fittings, Gaskets and Armored Flexible Hoses. Specify whether 230 VDC or 115 VAC for the bleeder operation. A manually operated bleeder is also available. Less Brake Wheel. 139 LBS Net.
8''-HM-2 Ametek Gemco 8 X 3.25 Inch Hydraulic Brake System Type HM for Progressive / Controlled Stopping Torque and Parking. Torque range of 0 through 200 FT LBS. via Foot Pedal Pressure along with Spring Set Parking & Holding. Parking Torque 50 FT LBS. Includes one 8 Inch Diameter Hydraulic Brake Assembly, HM Control Unit, Parking Brake Control station with Signal Light, Foot Pedal & Control Cylinder, Fluid Reservoir / Bleeder, Bleeder Pushbutton, 150 FT Copper Hydraulic Tubing, Wagner 21B Super Heavy Duty Brake Fluid, Fittings, Gaskets and Armored Flexible Hoses. Specify whether 230 VDC or 115 VAC for the bleeder operation. A manually operated bleeder is also available. Less Brake Wheel. 139 LBS Net.
8020 Ametek Gemco AHM / ERC System. Qty. 2, 18 X 8 Inch Type HM Brakes. Includes Qty. 2, J007905 Brake Actuators, Qty. 2, 18 X 8 Type HM Hydraulic Brakes, J066962 Treadle Vale Installation Kit, J0790942 Air Compressor 3/4 HP, J071030 Tubing Installation Kit, J073900 Tubing Kit (2 Hoses & 50 Feet of Tubing) J073903 Tubing Kit (4 Hoses with 200 Feet of Tubing) AHM / ERC Panel, DC 1 X 8 Ratio, Qty 2, PSD0180100 FRB Unit
8020-0042 Ametek Gemco AH/ERC Conversion System. Converts a Type ''H'' Brake System (without parking) into a Electrically Controlled System. Includes one J070943 Air Compressor 3/4 HP 230 VDC., one J070972 AH/ERC Control Panel 230 VDC pre-piped and pre-wired, one J073910 Installation Kit which includes tubing, fittings, unions, gaskets and brake fluid. Panel has one JC54086 Pressure Cluster for 1 & 2 brake systems. ''Small Panel'' 27 Inches Wide X 33 Inches High
8020-0044 Ametek Gemco AH/ERC Brake Conversion System, 480 VAC, includes one 8 to 1 Ratio pressure cluster on 70970 control panel, one 3/4 HP 70942 AC Compressor and J073910 tubing installation kit. For use with existing manual hydraulic foot pedal in cab and existing single 18'' hydraulic brake
8020-0046 Ametek Gemco: Brake System: Conversion: AHM/ERC Conversion System. Converts a Type ''H'' Brake System (without parking) into a Electrically Controlled System. Includes one J070943 Air Compressor 3/4 HP 230 VDC., one J100650 AHM/ERC Control Panel 230 VDC pre-piped and pre-wired, one J073910 Installation Kit which includes tubing, fittings, unions, gaskets and brake fluid. One PSD0180101 Fluid Reservoir Bleeder 230 VDC. Panel has one JC54086 Pressure Cluster for 1 & 2 brake systems. Panel Dim. 33 Inches Wide X 45 Inches High
8020-0052 Ametek Gemco AH/ARC Conversion System from manually operated Type H systems (without parking) to air over hydraulic. (2 brake system) Includes one 3/4 HP motor driven compressor, one pre-piped, pre-wired control panel, one installation kit including hose, tubing, fittings. 230VDC, 8:1 pressure ratio. Air treadle valve sold separately.
8020-0621 Ametek Gemco Conversion System for a 10 Inch Hyd System from H To HM
8020-1409 Ametek Gemco AH/ERC Conversion System for 4 brake system. Includes the following: J070943 Air Compressor 3/4 HP 230VDC, J070896T AH/ERC Control Panel with 2, 8:1 Pressure Clusters & J073910 Tubing Installation Kit. Treadle Valve and fluid reservoir bleeders are not included.
8020-1433 Ametek Gemco Conversion System. Type ''H'' Hydraulic Brake Systems to ''HM'' Hydraulic Brake System with a Parking Feature. for one 14 X 6 Inch Brake. Includes one each of the following: J023437 Brake Actuator, J045767 Control Station switch with Lamp, J070899 Kit Modifier, J073900 Installation Kit with 50 Ft Copper Tubing, 2 Armored Hoses & Fittings, J079462 14 Inch HM Brake Cylinder, PSD0180101 Fluid Reservoir Bleeder 230 VDC
8020-1440 Ametek Gemco AH/ERC Conversion system for use with a single hydraulic brake. Includes 70943 compressor 3/4HP 230VDC, 70984T panel with one 8:1 pressure cluster, 66962 treadle valve installation kit including 107039 treadle valve, 71030 tubing installation kit.
80200002 Ametek Gemco Type H Brake System Qty 1, 6 X 3
80200013 Ametek Gemco Hydraulic Brake System, Complete Type H Brake System. Infinitely Progressive Braking Torque, 0 to 400 Foot LBS via Foot Pedal Pressure based on a Maximum Pedal Pressure of 70 LBS. Includes Qty. 2, 8 Inch Hydraulic Brake Assemblies J002779, 230 Volt DC Fluid Reservoir Bleeder, Bleeder Pushbutton Station J10008, Control Cylinder J017616 with Pedal J008219, J73901 Installation Kit which includes, 250 Feet of Copper Tubing, Tube clamps, Tube Bushings, Tube Fittings, Tube Unions, Tube Tee, Qty.6, Armored Hose Kits J010797 & 1 Gallon of Wagner 21B Brake Fluid F9314 (189LBS)
80200015 Ametek Gemco Hydraulic Brake System, Complete Type H Brake System. Infinitely Progressive Braking Torque, 0 to 400 Foot LBS via Foot Pedal Pressure based on a Maximum Pedal Pressure of 70 LBS. Includes Qty. 2, 10 Inch Hydraulic Brake Assemblies J002926, Fluid Reservoir Bleeder, Bleeder Pushbutton Station J10008, Control Cylinder J017616 with Pedal J008219, J73901 Installation Kit which includes, 250 Feet of Copper Tubing, Tube clamps, Tube Bushings, Tube Fittings, Tube Unions, Tube Tee, Qty.6, Armored Hose Kits J010797 & 1 Gallon of Wagner 21B Brake Fluid F9314. Brake Wheels are not included. Please specify whether the Fluid Reservoir Bleeder is to be AC DC or manually via a 1/4 Turn Ball Valve (189LBS)
80200042 Ametek Gemco AH/ERC Conversion System, for 230 VDC, with a Single 8 X 1 Pressure Cluster
80200052 Ametek Gemco AH/ARC Conversion System, VDC
802002-0288 Ametek Gemco Bridge Brake System, Qty. 4, 10X4 Brakes, Single Station, Type A/H-ARC Complete System less brake wheels. Supply voltage 230 VDC, with 7/8 inch brake actuators and 1X5 ratio A/H pressure cluster for maximum torque of 380 LBS FT per brake
80201500 Ametek Gemco AH/ERC, 230 VDC, 2 Brake 18 Inch Hyd Brake, Moving Cab No Pedal
81101008 Ametek Gemco Heavy Duty AISE Spring Set Magnetic Release Shoe Brake Assembly, Direct Current Clapper Type, 10 Inch Wheel Diameter, Voltage DC with Shunt Wound Coils. 200 FT. LBS. 1 Hour. The TMSC Brake has interlocking shoe arms that allow single point adjustment for lining wear. Brake Weight 165 LBS. Net 190 LBS Gross. A 10 X 3.75 Inch Brake Wheel is not included. This brake is also available to operate via a hydraulic slave cylinder for progressive brake application from a crane cab. A Rectifier for AC Voltages is an available option
8138 Ametek Gemco Belt for the Air Compressor & Motor Assembly
8210-6-16-A-S-Y-X-X-L Ametek Gemco Electro-Thrust Brake Assembly. Series 8210
16 = 16 Inch Diameter Brake / Wheel
6 = 230 Volt DC Thruster Motor
A = X-Former Thruster Oil providing an operating range of -13 thru 104 Degrees F
S = Setting Delay Valve Included / Brake Setting Times with the Adjustable Valve 0.80 to 3.8 Sec., to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application
Y = Self Adjusting Mechanism providing automatic compensation for lining wear
X = No Limit switches
X = No Hand Relased
L = Left Hand Actuator Orientation
Torque Rating 1000 LB FT
Built to AISE Specifications (same foot print, relationship to brake wheel & torque as a TM-1665)
Spring Applied Electrohydraulic Release
L = Left Hand Actuator Orientation (400LBS)
8210-8-4-A-S-X-X-N-I Ametek Gemco Electro-Thrust Brake Assembly, 8 Inch Diameter Brake, 100 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications (same foot print, relationship to brake wheel & torque as a TM-83), Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F., Brake Setting Times with the Adjustable Valve 1.5 to 7.2 Sec., to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. Includes a Non-Latching Hand Release 140 LBS + skid. Ships via motor freight
8210-8-4-A-S-X-X-X-I Ametek Gemco Electro-Thrust Brake Assembly, 8 Inch Diameter Brake, 100 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications (same foot print, relationship to brake wheel & torque as a TM-83), Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F., Brake Setting Times with the Adjustable Valve 1.5 to 7.2 Sec., to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. 140 LBS + skid. Ships via motor freight
82101056 Ametek Gemco Electro-Thrust Brake Assembly, 14 Inch Diameter, 800 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake, 320 LBS + skid Ships via motor freight. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal
909-12-CD-4-R-SP Ametek Gemco Kam-Way Linear Limit Switch Series 909-12-CD-4-R-SP
12 = 12 Inches of Active travel
CD = Limit Switch with Cable Drive
4 = 4 Switches
R = Right Hand Assembly
SP = Single Pole Double Throw Switches
909-66-AA-10-R Ametek Gemco Series 909. Since we do not know exact part number this is our best estimate. A 66 Inch Stroke is a special unit
925-1623 Ametek Gemco Linear Cable Reel Sensor. Like model 925-A2-78-72-S-X
A2 = 97 to 192 Inch Stroke Mechanical Capacity
78 = 78 Inch Active Stroke
72 = 72 Inches of Initial Lead In Cable
S = Single Turn Resolver. Resolver single is to be fed to a converting device, which is not included
X = No Other Options
Engineer part number and product. Has a gear ratio that allows the 04535001or SD0308900 resolver to turn 1 revolution for every 11 inches of active travel / stroke
1/7 (15LBS)
925-1675 Ametek Gemco Linear Cable Reel Sensor with 60 Inches of Active Stroke and an 18 Inch Lead in Cable 05
925-A2-136-90-S-X Ametek Gemco Linear Cable Reel Sensor. Model 925-A2-136-90-S-X
A2 = 97 to 192 Inch Stroke Mechanical Capacity
136 = 136 Inch Active Stroke Electronically, The single turn resolver will make a 350 degree turn over this length. recommend use of 132 or 138 (6'' increments)
90 = 90 Inches of Initial Lead in Cable
S = Single Turn Resolver. Resolver single is to be fed to a converting device which is not included
X = No Other Options
925-A2-144-72-S-X Ametek Gemco Linear Cable Reel Sensor. Model 925-A2-144-72-S-X
A2 = 97 to 192 Inch Stroke Mechanical Capacity
144 = 144 Inch Active Stroke Electronically, The single turn resolver will turn 350 degrees turn over this length.
72 = 72 Inches of Initial Lead in Cable
S = Single Turn Resolver is to be fed to a converting device which is not included
X = No Other Options
925-A2-192-X-S-X Ametek Gemco Linear Cable Reel Sensor. Model 925-A2-192-X-S-X
A2 = 97 to 192 Inch Stroke Mechanical Capacity
192 = 192 Inch Active Stroke Electronically, The single turn resolver will turn 350 degrees turn over this length.
X = 0 Initial Lead In Cable Required
S = Single Turn Resolver is to be fed to a converting device which is not included
X = No Other Options
925-A2-78-72-S-X Ametek Gemco Linear Cable Reel Sensor. Model 925-A2-78-72-S-X
A2 = 97 to 192 Inch Stroke Mechanical Capacity
78 = 78 Inch Active Stroke
72 = 72 Inches of Initial Lead In Cable
S = Single Turn Resolver. Resolver single is to be fed to a converting device, which is not included
X = No Other Options
925-B1-168-72-S-X Ametek Gemco Linear Cable Reel Sensor. Model 925-B1-168-72-S-X
B1 = 193 to 480 Inch Stroke Mechanical Capacity / Single Main Spring
168 = 168 Inch Active Stroke
72 = 72 Inches of Initial Lead In Cable
S = Single Turn Resolver. Resolver single is to be fed to a converting device, which is not included
X = No Other Options
925-B1-201-108-S-X Ametek Gemco Linear Cable Reel Sensor
Model 925-B1-201-108-S-X
B1 = 193 to 480 Inch Stroke / Single Spring
201 = 201 Inch Active Stroke
108 = 108 Inches of Initial Cable Lead in
S = Single Turn Resolver. Resolver signal is to be fed to a converting device, not included
X = No Other Options
940-0060-3E Ametek Gemco Linear Position Sensor
6 Inch Active Stroke
4 to 20mA
Loop Power
(6LBS)
940-0070-3E Ametek Gemco Linear Position Sensor
7 Inch Active Stroke
4 to 20mA
Loop Power
(6LBS)
940-0100-3E Ametek Gemco Linear Position Sensor
10 Inch Active Stroke
4 to 20mA
Loop Power
(6LBS)
940-0120-3E Ametek Gemco Linear Position Sensor
12 Inch Active Stroke
4 to 20mA
Loop Power
(6LBS)
940-0180-1E Ametek Gemco Linear Position Sensor
18 Inch Active Stroke
0 to 10 VDC 3 Wire
(6LBS)
948001 Ametek Gemco Limit Module
Supplies 4 Adjustable Set Points / Limits on an LDT or other analog output device
Sinking, 0 - 10 Volts DC
948002 Ametek Gemco Limit Module
Supplies 4 Adjustable Set Points / Limits on an LDT or other analog output device
Sourcing, 0 - 10 Volts DC
949-003 Ametek Gemco Mounting Kit. LDT Mounting Kit includes, Head ''L'' Bracket M0748600 and the Probe Support Bracket SD0411200
949-005 Ametek Gemco Mounting Kit. Magnet Mounting Kit for LDT's. Non Ferrous Stainless Steel. Requires the use of the Large Split Magnet. For use with probes 940, 950IS, 951, 952 & 952QD (1LB)
949-019L12 Ametek Gemco Cable Connector for a 955A LDT. 5 Pin Straight Connector by 12 Foot Long
949-019L6 Ametek Gemco Cable Connector for a 955A LDT. 5 Pin Straight Connector by 6 Foot Long
949-021L12 Ametek Gemco Cable Connector. 6 Pin, 12 Foot with a straight connector
949-021L6 Ametek Gemco Cable Connector. 6 Pin, 6 Foot with a straight connector
949-022L12 Ametek Gemco Cable Assembly. 6 Pin Connector by 12 Foot with a Right Angle Connector
949-022L6 Ametek Gemco Cable Assembly. 6 Pin Connector by 6 Foot with a Right Angle Connector
949-023L15 Ametek Gemco Cable Assembly 23 Feet
949001L12 Ametek Gemco Cable Assembly. Cable with 12mm Euro Straight Connector, 12 Foot Length. For connection of 955S, 955LC, 956S & 956LC LDT's to the PLS
949001L6 Ametek Gemco Cable Assembly. Cable with 12mm Euro Straight Connector, 6 Foot Length. For connection of 955S, 955LC, 956S & 956LC LDT's to the PLS
949002L12 Ametek Gemco Cable Connector, 4 Pin, 12 Foot with Right angle 12mm Euro Connector. Compatible with 956S & LC LDT''S (1LB)
949002L6 Ametek Gemco Cable Assembly for use with the 955S & LC LDT'S. 4 Pin Micro 12mm Euro Straight Cable by 6 Foot Long (2LBS)
949003 Ametek Gemco Mounting Kit. Probe Mounting Kit. Includes End Clamp M0748600 & Rod Support Bracket SD0411200. Non Ferrous Stainless Steel. For use with probes 940, 950IS, 951, 952 & 952QD Does not include magnet mount bracket
949005 Ametek Gemco Mounting Kit. Magnet Mounting Kit for LDT's. Non Ferrous Stainless Steel with Hardware. Requires the use of the Large Split Magnet. For use with probes 940, 950IS, 951, 952 & 952QD (1LB)
949011L12 Ametek Gemco Cable Assembly with Straight Micro Plug Connector for a 953 VMAX LDT. 12 Foot Long, 5 Pole Turck RK 4.5T-4/S618, 12mm Euro Connector, Shielded
949011L6 Ametek Gemco Cable Assembly with Straight Micro Plug Connector for a 953 VMAX LDT. 6 Foot Long, 5 Pole Turck RK 4.5T-4/S618, 12mm Euro Connector, Shielded
949012L12 Ametek Gemco Cable Connector for a 953 VMAX LDT. 12 Foot, 5 Pin Right Angle 12mm Euro Connector (Shielded)
949012L6 Ametek Gemco Cable Connector for a 953 VMAX LDT. 6 Foot, 5 Pin Right Angle 12mm Euro Connector (Shielded)
949019L12 Ametek Gemco Cable Connector. 5 Pin, 12 Foot Straight Connector for the 955A LDT. Other Lengths and Right Angle Connectors are available
949019L30 Ametek Gemco Cable Connector. 5 Pin, 30 Foot Straight Connector for the 955A LDT. Other Lengths and Right Angle Connectors are available
949019L6 Ametek Gemco Cable Connector. 5 Pin, 6 Foot Straight Connector for the 955A LDT. Other Lengths and Right Angle Connectors are available
949020L12 Ametek Gemco Cable Assembly. 5 Pin, 12 Foot with a Right Angle Cable Connector used with 956A LDT's
949020L6 Ametek Gemco Cable Assembly. 5 Pin, 6 Foot with a Right Angle Cable Connector. For use with 956A LDT
949023L12 Ametek Gemco Cable Assembly for a 955DQ & 956DQ LDT. 12 Pin Straight Connector for option ''E'' Euro Connector, 12 mm, by 12 Feet Long . Other lengths available add $ 2.00 per foot and change the last 2 digits of the part number
949023L25 Ametek Gemco Cable Assembly for a 955DQ & 956DQ LDT. 12 Pin Straight Connector for option ''E'' Euro Connector, 12 mm, by 25 Feet Long . Other lengths available add or subtract $ 2.00 per foot and change the last 2 digits of the part number
949030L12 Ametek Gemco Cable Assembly
950-1510 Ametek Gemco 951A Linear Distance Transducer 951A with a 31.9 Inch Stroke & a 950 Mill Duty Housing 1/8
950-1527 951AC10319N2D10.9E LDT $ 883.00
950MD31.89A0B05.9OCXX $ 983.00
2/8
950-1586 Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950-1586 an Engineered Part Number
12 Inch Active Stroke
Rear Trunion Mount
Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly
950-1677-0310 Ametek Gemco Mill Duty Housing for Linear Displacement Transducers 950-1677-0310
0310 = 31 Inch Active Stroke
B2 Protective Boot, Silicone Coated Fiberglass for a increased Temperature Range of -110 to 550 Degrees F
Air Purge Ports
Front & Rear Mount Spherical Rod End by 3/4 Inch
950-1677-0780 Ametek Gemco Mill Duty Housing for Linear Displacement Transducers 950-1677-0310
0780 = 78 Inch Active Stroke
B2 Protective Boot, Silicone Coated Fiberglass for a increased Temperature Range of -110 to 550 Degrees F
Air Purge Ports
Front & Rear Mount Spherical Rod End by 3/4 Inch
9501445-0380 Ametek Gemco Linear Distance Transducer
Intrinsically Safe LDT is UL Listed for Class 1, Groups C & D; Class II, Groups E, F & G; and Class III, Hazardous Locations, when properly installed
0605 = 60.5 Inches of Stroke
Cable Assembly with a Straight Connector 04521210 by 6 Foot Long is included
9501445-0605 Ametek Gemco Linear Distance Transducer
Intrinsically Safe LDT is UL Listed for Class 1, Groups C & D; Class II, Groups E, F & G; and Class III, Hazardous Locations, when properly installed
0605 = 60.5 Inches of Stroke
Cable Assembly with a Straight Connector 04521210 by 6 Foot Long is included

9501446-115-0380 Ametek Gemco Analog Transceiver for a 9501445 Linear Distance Transducer
115 = 115 VDC Input Power
0380 = 38 Inch Stroke
9501446-115-0605 Ametek Gemco Analog Transceiver for a 9501445 Linear Distance Transducer
115 = 115 VDC Input Power
0605 = 60.5 Inch Stroke
9501446-230-0605 Ametek Gemco Analog Transceiver for a 9501445 Linear Distance Transducer
230 = 230 VDC Input Power
0605 = 60.5 Inch Stroke
9501446-24-0605 Ametek Gemco Analog Transceiver for a 9501445 Linear Distance Transducer
24 = 24 VDC Input Power
0605 = 60.5 Inch Stroke
950MD-11A-0B-0C-X-X Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-11A-0B-0C-X-X
11A = 11 Inch Active Stroke
0B = 0 Overstroke / Fully Retracted Overstroke in Inches
0C = 0 Overstroke / Fully Extended Overstroke in Inches
X = Standard 1/2 Inch NPT Conduit Fitting
X = No other options
Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The Front mount has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees
950MD-12A-0B-0C-X-X Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-12A-0B-0C-X-X
12A = 12 Inch Active Stroke
0B = 0 Overstroke / Fully Retracted Overstroke in Inches
0C = 0 Overstroke / Fully Extended Overstroke in Inches
X = Standard 1/2 Inch NPT Conduit Fitting
X = No other options
Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The Front mount has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees
950MD-14A-0B-0C-C2-R Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-14A-0B-0C-C2-R
14A = Active stroke in Inches
0B = 0 Overstroke / Fully Retracted Overstroke in Inches
0C = 0 Overstroke / Fully Extended Overstroke in Inches
C2 = MS Style Connector and Mate on Side of Housing
R = Rear Mount Spherical Rod End 3/4 Inch with Mounting Bolt
Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The 3/4 Inch Rear Rod End attaches to a threaded bolt extending from the rear of the head. The Front mount also has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees
950MD-16A-0B-0C-X-X Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-16A-0B-0C-X-X
16A = 16 Inch Active Stroke
0B = 0 Overstroke / Fully Retracted Overstroke in Inches
0C = 0 Overstroke / Fully Extended Overstroke in Inches
X = Standard 1/2 Inch NPT Conduit Fitting
X = No other options
Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The Front mount has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees
950MD-18A-0B-0C-X-R Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-18A-0B-0C-C-R
18A = Active stroke in Inches
0B = 0 Overstroke / Fully Retracted Overstroke in Inches
0C = 0 Overstroke / Fully Extended Overstroke in Inches
X = Standard 1/2 Inch NPT Conduit Fitting
R = Rear Mount Spherical Rod End 3/4 Inch with Mounting Bolt
Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The 3/4 Inch Rear Rod End attaches to a threaded bolt extending from the rear of the head. The Front mount also has a Spherical Rod End by 1/2 Inch
950MD-18A-0B-0C-X-RF Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-18A-0B-X-RF
18A = Active stroke in Inches
0B = 0 Overstroke / Fully Retracted Overstroke in Inches
0C = 0 Overstroke / Fully Extended Overstroke in Inches
X = Standard 1/2 Inch NPT Conduit Fitting
RF = Front & Rear Mount Spherical Rod Ends have been specified. The 3/4 Inch Rear Rod End attaches to a threaded bolt extending from the rear of the head. The Front mount also has a Spherical Rod End by 3/4 Inch
Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications
950MD-20A-0B-0C-X-R Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-20A-0B-0C-X-R
20A = 20 Inch Active Stroke
0B = 0 Overstroke / Fully Retracted Overstroke in Inches
0C = 0 Overstroke / Fully Extended Overstroke in Inches
X = Standard 1/2 Inch NPT Conduit Fitting
R = Rear Mount Spherical Rod End 3/4 Inch with Mounting Bolt
Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The 3/4 Inch Rear Rod End attaches to a threaded bolt extending from the rear of the head. The Front mount also has a Spherical Rod End by 1/2 Inch
950MD-23A-18.4B-0C-X-X Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-23A-18.4B-0C-X-X
36A = 23 Inch Active Stroke
18.4B = 18.4 Inches of Overstroke / Fully Retracted Overstroke in Inches
0C = 5 Inches Overstroke / Fully Extended Overstroke in Inches
X= Standard 1/2 Inch NPT Conduit Fitting
X = No other options
Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. A rear Trunion Mount is provided for mounting either directly in front of the head Assembly or on the rear of the head. The Front mount has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees
950MD-24A-0.5B-0.5C-C2-X Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-24A-0.5B-0.5C-C2-X
24A = 24 Inch Active Stroke
0.5B = 0.5 Inches of Overstroke / Fully Retracted Overstroke in Inches
0.5C = 0.5 Inches Overstroke / Fully Extended Overstroke in Inches
C2 = MS Style Connector and Mate on the Side of the Housing, 951 & 952
X = No other options
Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The 3/4 Inch Rear Rod End attaches to a threaded bolt extending from the rear of the head. The Front mount also has a Spherical Rod End by 1/2 Inch. The head contains 2, plugged air purge ports for additional cooling if required
950MD-24A-0B-0C-X-F Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-24A-0B-0C-X-F
24A = 24 Inch Active Stroke
0B = 0 Overstroke / Fully Retracted Overstroke in Inches
0C = 0 Overstroke / Fully Extended Overstroke in Inches
X = Standard 1/2 Inch NPT Conduit Fitting
F = Front Mount Spherical Rod End 3/4 Inch with Mounting Bolt
Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The 3/4 Inch Rear Rod End attaches to a threaded bolt extending from the rear of the head. The Front mount also has a Spherical Rod End by 3/4 Inch
950MD-30A-0B-0C-X-B1 Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-30A-0B-0C-X-B1
30A = 46 Inch Active Stroke
0B = 0 None 0 Overstroke / Fully Retracted Overstroke in Inches
0C = 0 None 0 Overstroke / Fully Extended Overstroke in Inches
X = Standard 1/2 Inch NPT Conduit Fitting
B1 = Protective Boot - Neoprene Coated Nylon - 60 to 250 Degrees F
Protects the LDT for resistance to water and oil.
The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. A rear Trunnion Mount is provided for mounting either directly in front of the head assembly or on the rear of the head. The front mount has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees
950MD-30A-0B-0C-X-B3 Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-30A-0B-0C-X-B3
30A = 30 Inch Active Stroke
0B = 0 None 0 Overstroke / Fully Retracted Overstroke in Inches
0C = 0 None 0 Overstroke / Fully Extended Overstroke in Inches
X = Standard 1/2 Inch NPT Conduit Fitting
B3 = Protective Boot - Teflon Coated Fiberglass
Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. A rear Trunnion Mount is provided for mounting either directly in front of the head Assembly or on the rear of the head. The Front mount has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees
(23LBS)
950MD-32A-2B-2C-X-X Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-32A-2B-2C-X-X
32A = 32 Inch Active Stroke
2B = 2 Overstroke / Fully Retracted Overstroke in Inches
2C = 2 Overstroke / Fully Extended Overstroke in Inches
X = Standard 1/2 Inch NPT Conduit Fitting
X = No other mounting options
Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. A rear Trunnion Mount is provided for mounting either directly in front of the head Assembly or on the rear of the head. The Front mount has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees
950MD-33A-1B-1C-C2-X Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-33A-1B-1C-C2-X
33A = Active stroke in Inches
1B = 1 Inch Fully Retracted Overstroke in Inches
1C = 1 Inch Fully Extended Overstroke in Inches
C2 = MS Style Connector and mate on Side of Housing (951 & 952 LDT's only)
X = No Mounting or Extreme Condition Options
Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications
950MD-34A-0B-0C-X-F Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-24A-0B-0C-X-F
34A = 34 Inch Active Stroke
0B = 0 Overstroke / Fully Retracted Overstroke in Inches
0C = 0 Overstroke / Fully Extended Overstroke in Inches
X = Standard 1/2 Inch NPT Conduit Fitting
F = Front Mount Spherical Rod End 3/4 Inch with Mounting Bolt
Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The Front mount has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees. The Front mount also has a Spherical Rod End by 3/4 Inch
950MD-36A-0B-0C-C-X Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-36A-0B-0C-C-X
36A = 36 Inch Active Stroke
0B = 0 Inches of Overstroke / Fully Retracted Overstroke in Inches
0C = 0.5 Inches Overstroke / Fully Extended Overstroke in Inches
C = MS Style Connector and Mate on the Side of the Housing, for old 950 LDT
X = No other options
Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. A rear Trunnion Mount is provided for mounting either directly in front of the head Assembly or on the rear of the head. The Front mount has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees
950MD-36A-0B-0C-C2-R Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-36A-0B-0C-C2-R
36A = 36 Inch Active Stroke
0B = 0 Inches of Overstroke / Fully Retracted Overstroke in Inches
0C = 0.5 Inches Overstroke / Fully Extended Overstroke in Inches
C2 = MS Style Connector and Mate on Side of Housing
R = Rear Mount Spherical Rod End 3/4 Inch with Mounting Bolt
Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications.The 3/4 Inch Rear Rod End attaches to a threaded bolt extending from the rear of the head. The Front mount also has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees
950MD-36A-0B-0C-X-X Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-36A-0B-0C-X-X
36A = 36 Inch Active Stroke
0B = 0 Overstroke / Fully Retracted Overstroke in Inches
0C = 0 Overstroke / Fully Extended Overstroke in Inches
X = Standard 1/2 Inch NPT Conduit Fitting
X = No other mounting options
Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The Front mount has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees
950MD-43A-0B-0C-X-R Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-43A-0B-0C-X-R
43A = Active stroke in Inches
0B = 0 Overstroke / Fully Retracted Overstroke in Inches
0C = 0 Overstroke / Fully Extended Overstroke in Inches
X = Standard 1/2 Inch NPT Conduit Fitting
R = Rear Mount Spherical Rod End 3/4 Inch with Mounting Bolt
Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The 3/4 Inch Rear Rod End attaches to a threaded bolt extending from the rear of the head. The Front mount also has a Spherical Rod End by 1/2 Inch
950MD-45A-0B-0C-X-X Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-45A-0B-0C-X-X
45A = 45 Inch Active Stroke
0B = 0 Overstroke / Fully Retracted Overstroke in Inches
0C = 0 Overstroke / Fully Extended Overstroke in Inches
X = Standard 1/2 Inch NPT Conduit Fitting
X = No other mounting options
Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The Front mount has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees
950MD-46A-0B-0C-X-B1 Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-46A-0B-0C-X-B1
46A = 46 Inch Active Stroke
0B = 0 None 0 Overstroke / Fully Retracted Overstroke in Inches
0C = 0 None 0 Overstroke / Fully Extended Overstroke in Inches
X = Standard 1/2 Inch NPT Conduit Fitting
B1 = Protective Boot - Neoprene Coated Nylon - 60 to 250 Degrees F
Protects the LDT for resistance to water and oil.
The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. A rear Trunnion Mount is provided for mounting either directly in front of the head assembly or on the rear of the head. The front mount has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees
950MD-46A-0B-0C-X-R Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-46A-0B-0C-X-R
46A = Active stroke in Inches 46''
0B = 0 Overstroke / Fully Retracted Overstroke in Inches
0C = 0 Overstroke / Fully Extended Overstroke in Inches
X = Standard 1/2 Inch NPT Conduit Fitting
R = Rear Mount Spherical Rod End 3/4 Inch with Mounting Bolt
Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The 3/4 Inch Rear Rod End attaches to a threaded bolt extending from the rear of the head. The Front mount also has a Spherical Rod End by 1/2 Inch
950MD-60A-0B-0C-X-B1 Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-60A-0B-0C-X-B1
60A = 60 Inch Active Stroke
0B = 0 None 0 Overstroke / Fully Retracted Overstroke in Inches
0C = 0 None 0 Overstroke / Fully Extended Overstroke in Inches
X = Standard 1/2 Inch NPT Conduit Fitting
B1 = Protective Boot - Neoprene Coated Nylon - 60 to 250 Degrees F
Protects the LDT for resistance to water and oil.
The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. A rear Trunnion Mount is provided for mounting either directly in front of the head assembly or on the rear of the head. The front mount has a Spherical Rod End by 1/2 Inch which is adjustable by approximately 3/4 of an Inch and can rotate 360 degrees
950MD-60A-0B-0C-X-R Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-60A-0B-0C-X-R
60A = 60 Inch Active Stroke
0B = 0 Overstroke / Fully Retracted Overstroke in Inches
0C = 0 Overstroke / Fully Extended Overstroke in Inches
X = Standard 1/2 Inch NPT Conduit Fitting
R = Rear Mount Spherical Rod End 3/4 Inch with Mounting Bolt
Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The 3/4 Inch Rear Rod End attaches to a threaded bolt extending from the rear of the head. The Front mount also has a Spherical Rod End by 1/2 Inch
950MD-665A-0B-0C-C2-X Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-665A-0B-0C-C2-X
665A = 66.5 Inches of Active Stroke
0B = 0 Inch Fully Retracted Overstroke
0C = 0 Inch Fully Extended Overstroke
C2 = MS Style Connector and mate on Side of Housing (951 & 952 LDT's only)
X = No Mounting or Extreme Condition Options
Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications
950MD-7A-0B-0C-C2-X Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-7A-0B-0C-C2-X
24A = 24 Inch Active Stroke
0B = 0 Inches of Overstroke / Fully Retracted Overstroke in Inches
0C = 0.5 Inches Overstroke / Fully Extended Overstroke in Inches
C2 = MS Style Connector and Mate on the Side of the Housing, 951 & 952
X = No other options
Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications. The 3/4 Inch Rear Rod End attaches to a threaded bolt extending from the rear of the head. The Front mount also has a Spherical Rod End by 1/2 Inch. The head contains 2, plugged air purge ports for additional cooling if required
950MD-84A-0B-0C-X-R Ametek Gemco Mill Duty Housing for Linear Displacement Transducers
Model 950MD-84A-0B-0C-X-R
84A = 84 Inches of Active Stroke
0B = 0 Inch Fully Retracted Overstroke
0C = 0 Inch Fully Extended Overstroke
X = Standard 1/2 Inch conduit Fitting
R = Rear Mount Spherical Rod end 3/4 inch with Mounting Bolt
Protects the LDT from physical & environmental damage. The housing and body are manufactured from 304 stainless steel. A Rulon bearing assembly offers wear resistance and temperature immunity for the actuator assembly. Air purge ports are available at additional cost to allow clean, dry shop air to cool the electronics in high temp applications
951-1547 Ametek Gemco Linear Displacement Transducer. Quik-Stik II Engineered part number
951VP = Variable Pulse
3.2 Inch Stroke Length
2.7 Inch Dead Band
E = External Interrogation
E = Environmental MS Connector
Special Settings: Function 2, Wire Speed X 4 & Function F, Disable Fault Output
Pre- programmed by Ametek
(3LBS)
similar to a 951VP-0032-X-D2.7EE except with special settings to multiply wire speed x 4, and disable the fault output
951-CP-1996-30 Ametek Gemco LDT Sr GM22669A
9511405 Ametek Gemco Programmer & PC Interface. Hand Held Programmer for Series 951 Quik-Stik II LDT Analog Units. Programs voltage type, span, polarity, zero reference and velocity with ASCII characters which are used to represent each function. Programmer interfaces with the LTD through a small phone jack connection attached to the end of the LDT cable. Operates off of a 9 volt battery which is included along with all cables and hardware to interface one LDT
9511465 Ametek Gemco Linear Displacement Transducer. 4 inch stroke. 0 - 10 Volt DC Output with velocity set at 2.5 Inches / Second. 2 weeks to ship.
951A-C1-0040-X-X-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0040-X-X-E
951A = Analog Style
C1 = 4 to 20 mA Grounded (Sourcing)
0040 = 4 Inch Stroke Length
X = Standard 1.5 Inch Null
X = Standard 2.25 Inch Dead Zone
E = Environmental MS connector (mating connector and / or pigtail must be ordered separately
951A-C1-0050-N2-D2-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0050-N2-D2-E
951A = Analog Style
C1 = 4 to 20 mA Grounded (Sourcing)
0050 = 5 Inch Stroke Length
N2 = 2 Null Zone
D2 = 2 Inch Dead Zone
E = Environmental MS Connector
951A-C1-0060-N2-D5-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0060-N2-D5-E
951A = Analog Style
C1 = 4 to 20 mA Grounded (Sourcing)
0060 = 6 Inch Stroke Length
N2 = 2 Inch Null over the STANDARD 1.5 Inches
D5 = 5 Inch Dead Zone over the STANDARD 2.25 Inches
E = Environmental MS Connector
951A-C1-0060-N3-D5-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0060-N3-D5-E
951A = Analog Style
C1 = 4 to 20 mA Grounded (Sourcing)
0060 = 6 Inch Stroke Length
N3 = 3 Null Zone
D5 = 5 Inch Dead Zone
E = Environmental MS Connector
951A-C1-0070-N2-D5-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0070-N2-D5-E
951A = Analog Style
C1 = 4 to 20 mA Grounded (Sourcing)
0070 = 7 Inch Stroke Length
N2 = 2 Inch Null Zone
D5 = 5 Inch Dead Zone
E = Environmental MS Connector
951A-C1-0088-N2-D5-C12 Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0088-N2-D5-C12
951A = Analog Style
C1 = 4 to 20 mA Grounded (Sourcing)
0088 = 8.8 Inch Stroke Length
N2 = 2 Inch Null Zone over 1.5 Inches
D5 = Non Standard Dead Zone over 2.25 Inches
C12 = Potted Pigtail Assembly by 12 Feet
951A-C1-0098-X-X-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0098-X-X-E
951A = Analog Style
C1 = 4 to 20 mA Grounded (Sourcing)
0098 = 9.8 Inch Stroke Length
X = Standard 1.5 Inch Null
X = Standard 2.25 Inch Dead Zone
E = Environmental MS connector (mating connector and / or pigtail must be ordered separately
951A-C1-0113-X-X-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0113-X-X-E
951A = Analog Style
C1 = 4 to 20 mA Grounded (Sourcing)
0113 = 11.3 Inch Stroke Length
X = Standard 1.5 Inch Null
X = Standard 2.25 Inch Dead Zone
E = Environmental MS connector (mating connector and / or pigtail must be ordered separately
951A-C1-0183-N2-D5-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0183-N2-D5-E
951A = Analog Style
C1 = 4 to 20 mA Grounded (Sourcing)
0183 = 18.3 Inch Stroke Length
N2 = 2'' Null over 1.5 Inches
D5 = 5'' Dead Zone over 2.25 Inches
E = Environmental MS Connector
951A-C1-0210-X-X-C15 Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0210-X-X-C15
951A = Analog Style
C1 = 4 to 20 mA Grounded (Sourcing)
0210 = 21.0 Inch Stroke Length
X = Standard 1.5 Inch Null
X = Standard 2.25 Inch Dead Zone
C15 = Potted Pigtail Assembly by 15 Feet
951A-C1-0220-N2-D5-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0220-N2-D5-E
951A = Analog Style
C1 = 4 to 20 mA Grounded (Sourcing)
0220 = 22.0 Inch Stroke Length
N2 = 2 Inch Null Zone
D5 = 5 Inch Dead Zone
E = Environmental MS Connector
951A-C1-0240-N2-D5-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0240-N2-D5-E
951A = Analog Style
C1 = 4 to 20 mA Grounded (Sourcing)
0240 = 24.0 Inch Stroke Length
N2 = 2 Inch Null Zone
D5 = 5 Inch Dead Zone
E = Environmental MS Connector
951A-C1-0321-N2-X-C12 Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0321-N2-X-C12
951A = Analog Style
C1 = 4 to 20 mA Grounded (Sourcing)
0321 = 32.1 Inch Stroke Length
N2 = 2 Inch Null Zone over 1.5 Inches
X = Standard Dead Zone of 2.25 Inches
C12 = Potted Pigtail Assembly by 12 Feet
951A-C1-0330-N3-D6-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0330-N3-D6-E
951A = Analog Style
C1 = 4 to 20 mA Grounded (Sourcing)
0330 = 33 Inch Stroke Length
N3 = 3 Null over 1.5 Inches
D6 = Dead Zone over 2.25 Inches
E = Environmental MS Connector
951A-C1-0360-N2-D5-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0360-N2-D5-E
951A = Analog Style
C1 = 4 to 20 mA Grounded (Sourcing)
0360 = 36 Inch Stroke Length
N2 = 2 Inch Null Zone
D5 = 5 Inch Dead Zone
E = Environmental MS Connector
951A-C1-0384-N2-D5-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0384-N2-D5-E
951A = Analog Style
C1 = 4 to 20 mA Grounded (Sourcing)
0384 = 38.4 Inch Stroke Length
N2 = 2'' Null over 1.5 Inches
D5 = 5 '' Dead Zone over 2.25 Inches
E = Environmental MS Connector
951A-C1-0450-N2-D5-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0450-N2-D5-E
951A = Analog Style
C1 = 4 to 20 mA Grounded (Sourcing)
0450 = 45 Inch Stroke Length
N2 = 2 Inch Null Zone
D5 = 5 Inch Dead Zone
E = Environmental MS Connector
951A-C1-0460-X-X-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0460-X-X-E
951A = Analog Style
C1 = 4 to 20 mA Grounded (Sourcing)
0460 = 46 Inch Stroke Length
X = Standard 1.5 Inch Null
X = Standard 2.25 Inch Dead Zone
E = Environmental MS connector (mating connector and / or pigtail must be ordered separately
951A-C1-0493-N2-D5-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-0493-N2-D5-E
951A = Analog Style
C1 = 4 to 20 mA Grounded (Sourcing)
0493 = 49.3 Inch Stroke Length
N2 = 2 Inch Null Zone
D5 = 5 Inch Dead Zone
E = Environmental MS Connector
951A-C1-1320-X-X-C10 Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-1320-X-X-C10
951A = Analog Style
C1 = 4 to 20 mA Grounded (Sourcing)
1320 = 132 Inch Stroke Length
X = Standard 1.5 Inch Null
X = Standard 2.25 Inch Dead Zone
C10 = Potted Pigtail Assembly by 10 Feet
951A-C1-2335-N3.3-D2-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C1-2335-N3.3-X-E
951A = Analog Style
C1 = 4 to 20 mA Grounded (Sourcing)
233.5 = 233 & 1/2 Inch Stroke Length
N3.3 = 3.3 Inch Null Zone
X = Standard Dead Zone of 2 .25 Inches
E = Environmental MS Connector
(108LBS)
951A-C2-0150-X-X-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C2-0150-X-X-E
951A = Analog Style
C2 = 20-4mA Ungrounded, Sinking
0150 = 15 Inch Stroke Length
X = Standard 1.5 Inch Null
X = Standard 2.25 Inch Dead Zone
E = Environmental MS connector (mating connector and / or pigtail must be ordered separately
951A-C2-0250-X-X-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-C2-0250-X-X-E
951A = Analog Style
C2 = 20-4mA Ungrounded, Sinking
0250 = 25 Inch Stroke Length
X = Standard 1.5 Inch Null
X = Standard 2.25 Inch Dead Zone
E = Environmental MS connector (mating connector and / or pigtail must be ordered separately
951A-V-0010-X-X-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0040-X-X-E
951A = Voltage
0040 = 4 Inch Stroke Length
X = Standard 1.5 Inch Null Length
X = Standard Dead Zone of 2.25 Inches
E = Environmental MS Connector
951A-V-0040-X-X-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0040-X-X-E
951A = Voltage
0040 = 4 Inch Stroke Length
X = Standard 1.5 Inch Null Length
X = Standard Dead Zone of 2.25 Inches
E = Environmental MS Connector
951A-V-0042-X-X-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0042-X-X-E
951A = Voltage
0042 = 4.20 Inch Stroke Length
X = Standard 1.5 Inch Null Length
X = Standard Dead Zone of 2.25 Inches
E = Environmental MS Connector
951A-V-0060-X-X-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0060-X-X-E
951A = Voltage
0060 = 6 Inch Stroke Length
X = Standard 1.5 Inch Null Length
X = Standard Dead Zone of 2.25 Inches
E = Environmental MS Connector
951A-V-0070-N2-D5-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0150-N2-D5-E
951A = Voltage
0070 = 7 Inch Stroke Length
N2 = 2 Inch Null Length
D5 = 5 Inch Dead Zone
E = Environmental MS Connector
951A-V-0080-X-X-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0040-X-X-E
951A = Voltage
0080 = 8 Inch Stroke Length
X = Standard 1.5 Inch Null Length
X = Standard Dead Zone of 2.25 Inches
E = Environmental MS Connector
951A-V-0100-X-X-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0100-X-X-E
951A = Voltage
0100 = 10 Inch Stroke Length
X = Standard 1.5 Inch Null Length
X = Standard Dead Zone of 2.25 Inches
E = Environmental MS Connector
(4LBS)
951A-V-0110-N2-D5-C12 Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0110-N2-D5-C12
951A = Analog LDT
V = Voltage Outputs
0110 = 11 Inch Stroke Length
N2 = 2 Inch Null Length
D5 = 5 Inch Dead Zone
C12 = Potted Pigtail cable Assembly by 12 Feet Long
951A-V-0120-X-X-C12 Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0120-X-X-C12
951A = Voltage
0120 = 12 Inch Stroke Length
X = Standard 1.5 Inch Null Length
X = Standard Dead Zone of 2.25 Inches
C12 = Potted Pigtail Assembly by 12 FT
951A-V-0140-N2-D5-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0140-N2-D5-E
951A = Voltage
0140 = 14 Inch Stroke Length
N2 = 2 Inch Null Length
D5 = 5 Inch Dead Zone
E = Environmental MS Connector
951A-V-0140-X-X-C-12 Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0140-X-X-C12
951A = Voltage
0140 = 14 Inch Stroke Length
X = Standard 1.5 Inch Null Length
X = Standard Dead Zone of 2.25 Inches
C12 = Potted Pigtail Assembly by 12 FT
951A-V-0140-X-X-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0140-X-X-E
951A = Voltage
0140 = 14 Inch Stroke Length
X = Standard 1.5 Inch Null Length
X = Standard Dead Zone of 2.25 Inches
E = Environmental MS Connector
(4LBS)
951A-V-0150-N2-D5-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0150-N2-D5-E
951A = Voltage
0150 = 15 Inch Stroke Length
N2 = 2 Inch Null Length
D5 = 5 Inch Dead Zone
E = Environmental MS Connector
951A-V-0160-N2-D5-C12 Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0160-N2-D5-C12
951A = Analog LDT
V = Voltage Outputs
0160 = 16 Inch Stroke Length
N2 = 2 Inch Null Length
D5 = 5 Inch Dead Zone
C12 = Potted Pigtail cable Assembly by 12 Feet Long
951A-V-0180-N2-D5-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0180-N2-D5-E
951A = Voltage
0180 = 18 Inch Stroke Length
N2 = 3.5 Inch Null Length
D5 = 7.25 Inch Dead Zone
E = Environmental MS Connector
951A-V-0200-X-X-C12 Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0200-X-X-C12
951A = Voltage
0200 = 20 Inch Stroke Length
X = Standard 1.5 Inch Null Length
X = Standard Dead Zone of 2.25 Inches
C12 = Potted Pigtail Assembly by 12 FT
951A-V-0220-N2-D5-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0220-N2-D5-E
951A = Voltage
0220 = 22 Inch Stroke Length
N2 = 2 Inch Null Length
D5 = 5 Inch Dead Zone
E = Environmental MS Connector
(6LBS)
951A-V-0230-N18.4-D5-C12 Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0230-N18.4-D5-C12
951A = Voltage
0230 = 23 Inch Stroke Length
N18.4 = 18.4 Inch Null Length
D5 = 5 Inch Dead Band
C12 = Potted Pigtail Assembly
951A-V-0230-N18.4-X-C12 Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0230-N18.4-X-C12
951A = Voltage
0230 = 23 Inch Stroke Length
N18.4 = 18.4 Inch Null Length
X = Standard Dead Zone of 2.25 Inches
C12 = Potted Pigtail Assembly
951A-V-0240-N2-D5-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0240-N2-D5-E
951A = Voltage
0240 = 24 Inch Stroke Length
N2 = 2 Inch Null Length
D5 = 5 Inch Dead Zone
E = Environmental MS Connector
951A-V-0240-X-X-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0240-X-X-E
951A = Voltage
0240 = 24 Inch Stroke Length
X = Standard 1.5 Inch Null Length
X = Standard Dead Zone of 2.25 Inches
E = Environmental MS Connector
951A-V-0250-X-X-C15 Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0250-X-X-C15
951A = Voltage
0250 = 25 Inch Stroke Length
X = Standard 1.5 Inch Null Length
X = Standard Dead Zone of 2.25 Inches
C15 = Potted Pigtail Assembly by 15 FT
951A-V-0278-X-X-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0278-X-X-E
951A = Voltage
0278 = 27.8 Inch Stroke Length
X = Standard 1.5 Inch Null Length
X = Standard Dead Zone of 2.25 Inches
E = Environmental MS Connector
(6LBS)
951A-V-0300-X-X-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0300-X-X-E
951A = Voltage
0300 = 30 Inch Stroke Length
X = Standard 1.5 Inch Null Length
X = Standard Dead Zone of 2.25 Inches
E = Environmental MS Connector
951A-V-0315-N2-D5-C6 Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0315-N2-D5-C6
951A = Analog LDT
V = Voltage Outputs
0315 = 31.5 Inch Stroke Length
N2 = 2 Inch Null Length
D5 = 5 Inch Dead Zone
C6 = Potted Pigtail Assembly by 6 feet long
(7LBS)
951A-V-0315-N2-D5-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0315-N2-D5-E
951A = Voltage
0315 = 31.5 Inch Stroke Length
N2 = 2 Inch Null Length
D5 = 5 Inch Dead Zone
E = Environmental MS Connector
951A-V-0320-N3.5-X-C12 Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0320-N3-D5-C12
951A = Voltage Output
0320 = 32 Inch Stroke Length
N3 = 3 Inch Null Zonel Length
D5 = 5 Inch Dead Zone Lenght
C12 = 12 Foot Potted Pigtail Assembly
951A-V-0321-N2-X-C12 Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0321-N2-X-C12
951A = Analog LDT
V = Voltage Outputs
0321 = 32.1 Inch Stroke Length
N2 = 2 Inch Null Length
X = Standard Dead Zone of 2.25 Inches
C12 = Potted Pigtail cable Assembly by 12 Feet Long
951A-V-0340-N2-D5-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0340-N2-D5-E
951A = Voltage Output
0340 = 34 Inch Stroke Length
N2 = 2 Inch Null Length
D5 = 5 Inch Dead Zone
E = Environmental MS Connector
951A-V-0360-N2-D5-C12 Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0360-N2-D5-C12
951A = Analog LDT
V = Voltage Outputs
0360 = 36 Inch Stroke Length
N2 = 2 Inch Null Length
D5 = 5 Inch Dead Zone
C12 = Potted Pigtail cable Assembly by 12 Feet Long
951A-V-0360-N2-D5-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0360-N2-D5-E
951A = Voltage
0360 = 36 Inch Stroke Length
N2 = 2 Inch Null Length
D5 = 5 Inch Dead Zone
E = Environmental MS Connector
951A-V-0365-X-X-E Ametek Gemco 951A-V-0365-X-X-E Quik-Stik II, Linear Actuator, 0 to +10 VDC
951A-V-0490-N2-D5-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0490-N2-D5-E
951A = Voltage
0490 = 49 Inch Stroke Length
N2 = 2 Inch Null Length
D5 = 5 Inch Dead Zone
E = Environmental MS Connector
951A-V-0490-X-X-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0490-X-X-E
951A = Voltage
0490 = 49 Inch Stroke Length
X = Standard 1.5 Inch Null Length
X = Standard Dead Zone of 2.25 Inches
E = Environmental MS Connector
951A-V-0665-N2-D5-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0665-N2-D5-E
951A = Voltage
0665 = 66.5 Inch Stroke Length
N2 = 2 Inch Null Length
D5 = 5 Inch Dead Zone
E = Environmental MS Connector
951A-V-0900-X-X-C10 Ametek Gemco Linear Displacement Transducer. Series Quik-Stik II
Model 951A-V-090-X-X-C10
951A = Voltage
0900 = 90 Inch Stroke Length
X = Standard 1.5 Inch Null Length
X = Standard Dead Zone of 2.25 Inches
C10 = Potted Pigtail Assembly by 10 Foot
951A-V-0900-X-X-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951A-V-0900-X-X-E
951A = Voltage
0900 = 90 Inch Stroke Length
X = Standard 1.5 Inch Null Length
X = Standard Dead Zone of 2.25 Inches
E = Environmental MS Connector
951CP-0040-X-X-C100 Ametek Gemco Linear Displacement Transducer model 951CP-0040-X-X-C100
Quik-Stik II
CP = Control Pulse Version, generates digital outputs over a RS422 Line
This LDT is used with Gemco series 1989DL, 2120L1, 1996 & 1746L products
0040 = 4 Inch Stroke
X = Standard 1.5 inch Null Zone
X = Standard Dead Zone of 2.25 Inches
C100 = Potted PigTail Assembly by 100 Feet Long
951CP-0180-X-X-C100 Ametek Gemco Linear Displacement Transducer model 951CP-0180-X-X-C6
Quik-Stik II
CP = Control Pulse Version, generates digital outputs over a RS422 Line
This LDT is used with Gemco series 1989DL, 2120L1, 1996 & 1746L products
0180 = 18 Inch Stroke
X = Standard 1.5 inch Null Zone
X = Standard Dead Zone of 2.25 Inches
C6 = Potted PigTail Assembly by 6 Feet Long
951CP-0268-N2-D5-E Ametek Gemco Linear Displacement Transducer model 951CP-0268-N2-D5-E
Quik-Stik II
CP = Control Pulse Version, generates digital outputs over a RS422 Line
This LDT is used with Gemco series 1989DL, 2120L1, 1996 & 1746L products
0268 = 26.8 Inch Stroke
N2 = 2 Inch Null Zone
D5 = 5 Inch Dead Band
E = Environmental MS Connector
951CP-0268-X-X-E Ametek Gemco Linear Displacement Transducer model 951CP-0268-X-X-E
Quik-Stik II
CP = Control Pulse Version, generates digital outputs over a RS422 Line
This LDT is used with Gemco series 1989DL, 2120L1, 1996 & 1746L products
0268 = 26.8 Inch Stroke
X = Standard 1.5 inch Null Zone
X = Standard Dead Zone of 2.25 Inches
E = Environmental MS Connector
951CP-1996-12 Ametek Gemco Linear Displacement Transducer. This probe has an Active Travel of .1 to 12 Inches (5LBS)
951CP1996-17 Ametek Gemco Linear Distance Transducer with a 17 Inch Stroke for a 1996 Ram Set
951CP1996-30 Ametek Gemco Linear Distance Transducer with a 30 Inch Stroke for a 1996 Ram Set
951VP-0120-X-X-I-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951VP-0120-X-X-I-E
951VP = Variable Pulse
0120 = 12 Inch Stroke Length
X = Standard 1.5 Inch Null Length
I = Internal Interrogation
E = Environmental MS Connector
951VP-0199-X-X-I-E Ametek Gemco Quik-Stik II Linear Displacement Transducer. Model 951VP-0199-X-X-I-E
951VP = Variable Pulse
0199 = 19.9 Inch Stroke Length
X = Standard 1.5 Inch Null Length
X - Standard Dead Zone of 2.25 Inches
I = Internal Interrogation
E = Environmental MS Connector
951VP-1992-12 Ametek Gemco Linear Distance Transducer / LDT for use with the 1992 Press-Set Press Automation Controller
12 Inch Stroke Length (ram adjust mechanism in inches)
951VP-1992-33 Ametek Gemco Linear Distance Transducer / LDT for use with the 1992 Press-Set Press Automation Controller
33 Inch Stroke Length (ram adjust mechanism in inches)
952-1460240 Ametek Gemco Linear Displacement Transducer. Series 952 BlueOx
Model 952-1460240
952QD = Quadrature Version
24 Inch Stroke
RES 1000 with special filter routine
FORD Motor
952A-C4-0015-X-X-T Ametek Gemco Linear Displacement Transducer. Series 952 BlueOx
Model 925A-C4-0015-X-X-T
952A = Analog Output
C4 = Voltage Output 4 - 20 mA
0015 = Stroke 1.5 Inch
X = Standard 2.0 Inch Null
X = Standard Dead Zone 2.5 Inch
T = Threaded Metal Connector, fits MTS RBon Tempo II or III
952A-C4-0180-X-D5-C6 Ametek Gemco Linear Displacement Transducer. Series 952 BlueOx
Model 925A-C4-0180-X-D5-C6
952A = Analog Output
C4 = Voltage Output 4 - 20 mA
0180 = Stroke 18 Inch
X = Standard 2.0 Inch Null
D5 = Dead Zone 5 Inch
C6 = Potted Pigtail Assembly by 6 Foot
952A-C4-0180-X-X-C6 Ametek Gemco Linear Displacement Transducer. Series 952 BlueOx
Model 925A-C4-0180-X-X-C6
952A = Analog Output
C4 = Voltage Output 4 - 20 mA
0180 = Stroke 18 Inch
X = Standard 2.0 Inch Null
X = Standard 2.5 Inch Dead Band
C6 = Potted Pigtail Assembly by 6 Foot
952A-C4-0200-X-D5-E Ametek Gemco Linear Displacement Transducer. Series 952 BlueOx
952A = Analog Output
C4 = Voltage Output 4 - 20 mA
0200 = Stroke 20 Inch
X = Standard 1.5 Inch Null
D5 = Dead Zone 5 Inch
E = Environmental MS Connector. (mating connector is ordered separately)
952A-C4-0200-X-D5-S Ametek Gemco S = Standard 12 mm 5 Pin Euro Connector (CE Approved) Mating Connector and or Pigtails are ordered separately
952A-C4-0200-X-X-E Ametek Gemco Linear Displacement Transducer. Series 952 BlueOx
Model 925A-C4-0200-X-X-E
952A = Analog Output
C4 = Voltage Output 4 - 20 mA
0200 = Stroke 20 Inch
X = Standard 2.0 Inch Null
X = Standard Dead Zone 2.5 Inch
E = Environmental MS Connector (mating connector or pigtail must be ordered separately)
952A-C4-0230-X-X-E Ametek Gemco Linear Displacement Transducer. Series 952 BlueOx
Model 925A-C4-0230-X-X-E
952A = Analog Output
C4 = Voltage Output 4 - 20 mA
0230 = Stroke 23 Inch
X = Standard 2.0 Inch Null
X = Standard Dead Zone 2.5 Inch
E = Environmental MS Connector (mating connector or pigtail must be ordered separately)
952A-C4-0360-X-X-S Ametek Gemco Linear Displacement Transducer. Series 952 BlueOx
Model 925A-C4-0360-X-X-S
952A = Analog Output
C4 = Voltage Output 4 - 20 mA
0360 = Stroke 36 Inch
X = Standard 2.0 Inch Null
X = Standard Dead Zone 2.5 Inch
S = Standard Connector. 12 mm 5 Pin Euro connector. Mating connector 949-019 or 949-020 and or pigtail must be ordered separately
952A-C4-0430-X-D5-S Ametek Gemco Linear Displacement Transducer. Series 952 BlueOx
Model 925A-C4-0430-X-D5-S
952A = Analog Output
C4 = Voltage Output 4 - 20 mA
0430 = Stroke 43 Inch
X = Standard 2.0 Inch Null
D5 = Dead Zone 5 Inch
S = Standard 12mm 5 Pin Euro Connector. Mating connector949019 or 949020 and or pigtail must be ordered separately
952A-C4-0600-X-D5-S Ametek Gemco Linear Displacement Transducer. Series 952 BlueOx
Model 925A-C4-0600-X-D5-S
952A = Analog Output
C4 = Voltage Output 4 - 20 mA
0600 = Stroke 60 Inch
X = Standard 2.0 Inch Null
D5 = Dead Zone 5 Inch
S = Standard 12mm 5 Pin Euro Connector. Mating connector949019 or 949020 and or pigtail must be ordered separately
952A-C4-066-X-X-S Ametek Gemco Linear Displacement Transducer. Series 952 BlueOx
Model 925A-C4-0660-X-X-S
952A = Analog Output
C4 = Voltage Output 4 - 20 mA
0660 = Stroke 66 Inch
X = Standard 2.0 Inch Null
X = Standard Dead Zone 2.5 Inch
S = Standard Connector. 12 mm 5 Pin Euro connector. Mating connector 949-019 or 949-020 and or pigtail must be ordered separately
952A-V0-0010-X-X-S Ametek Gemco Linear Displacement Transducer model 952A-V0-0010-X-X-S
''Blue Ox''
A = Analog Version
V0 = Voltage Output 0 - 10 VDC
0010 = 1 Inch Stroke / Active Travel
X = Standard Null Zone of 2 Inches
X = Standard Dead Zone of 2.5 Inches
S = Standard Connector. 12 mm 5 Pin Euro connector ( mating connector 949-019 or 949-020 and or pigtail must be ordered separately)
952A-V0-0100-X-X-S Ametek Gemco Linear Displacement Transducer model 952A-V0-0100-X-X-S
''Blue Ox''
A = Analog Version
V0 = Voltage Output 0 - 10 VDC
0100 = 10 Inch Stroke / Active Travel
X = Standard Null Zone of 2 Inches
X = Standard Dead Zone of 2.5 Inches
S = Standard Connector. 12 mm 5 Pin Euro connector ( mating connector 949-019 or 949-020 and or pigtail must be ordered separately)
952A-V0-0200-X-D5-E Ametek Gemco Linear Displacement Transducer model 952A-V0-0200-X-D5-S
''Blue Ox''
A = Analog Version
V0 = Voltage Output 0 - 10 VDC
0180 = 18 Inch Stroke
X = Standard Null Zone of 2 Inches
D5 = Dead Zone of 5 Inches
S = Standard Connector. 12 mm 5 Pin Euro connector ( mating connector 949-019 or 949-020 and or pigtail must be ordered separately) 1/6
952A-V0-0205-X-X-T Ametek Gemco Linear Displacement Transducer model 952A-V0-0205-X-X-T
''Blue Ox''
A = Analog Version
V0 = Voltage Output 0 - 10 VDC
0205 = 20.5 Inch Stroke / Active Travel
X = Standard Null Zone of 2 Inches
X = Standard Dead Zone of 2.5 Inches
T = Threaded Metal Connector. Fits MTS RB on Tempo II or III
952A-V0-0720-X-X-S Ametek Gemco Linear Displacement Transducer model 952A-V0-0100-X-X-S
''Blue Ox''
A = Analog Version
V0 = Voltage Output 0 - 10 VDC
0720 = 72 Inch Stroke / Active Travel
X = Standard Null Zone of 2 Inches
X = Standard Dead Zone of 2.5 Inches
S = Standard Connector. 12 mm 5 Pin Euro connector ( mating connector 949-019 or 949-020 and or pigtail must be ordered separately)
952A-V1-0040-X-X-S Ametek Gemco Linear Displacement Transducer model 952A-V1-0040-X-X-S
''Blue Ox''
A = Analog Version
V1 = 10 to 0 VDC Output
0040 = 4 Inch Stroke
X = Standard Null Zone of 2 Inches
X = Standard Dead Zone of 2.5 Inches
S = Standard Connector. 12 mm 5 Pin Euro connector ( mating connector 949-019 or 949-020 and or pigtail must be ordered separately) 1/6
952A-V1-0072-X-X-S Ametek Gemco Linear Displacement Transducer model 952A-V1-0072-X-X-S
''Blue Ox''
A = Analog Version
V1 = 10 to 0 VDC Output
0072 = 7.2 Inch Stroke
X = Standard Null Zone of 2 Inches
X = Standard Dead Zone of 2.5 Inches
S = Standard Connector. 12 mm 5 Pin Euro connector ( mating connector 949-019 or 949-020 and or pigtail must be ordered separately) 1/6
952A-V1-0120-X-X-S Ametek Gemco Linear Displacement Transducer model 952A-V1-0120-X-X-S
''Blue Ox''
A = Analog Version
V1 = 10 to 0 VDC Output
0120 = 12 Inch Stroke
X = Standard Null Zone of 2 Inches
X = Standard Dead Zone of 2.5 Inches
S = Standard Connector. 12 mm 5 Pin Euro connector ( mating connector 949-019 or 949-020 and or pigtail must be ordered separately) 1/6
952A-V1-0180-X-X-S Ametek Gemco Linear Displacement Transducer model 952A-V1-0180-X-X-S
''Blue Ox''
A = Analog Version
V1 = 10 to 0 VDC Output
0180 = 18 Inch Stroke
X = Standard Null Zone of 2 Inches
X = Standard Dead Zone of 2.5 Inches
S = Standard Connector. 12 mm 5 Pin Euro connector,mating connector 949-019 or 949-020 and or pigtail must be ordered separately (5LBS) 1/6
952A-V1-0330-X-X-S Ametek Gemco Linear Displacement Transducer model 952A-V1-0330-X-X-S
''Blue Ox''
A = Analog Version
V1 = 10 to 0 VDC Output
0330 = 33 Inch Stroke
X = Standard Null Zone of 2 Inches
X = Standard Dead Zone of 2.5 Inches
S = Standard Connector. 12 mm 5 Pin Euro connector ( mating connector 949-019 or 949-020 and or pigtail must be ordered separately) 1/6
952A-V1-0400-X-X-S Ametek Gemco Linear Displacement Transducer model 952A-V1-0040-X-X-S
''Blue Ox''
A = Analog Version
V1 = 10 to 0 VDC Output
0400 = 40 Inch Stroke
X = Standard Null Zone of 2 Inches
X = Standard Dead Zone of 2.5 Inches
S = Standard Connector. 12 mm 5 Pin Euro connector ( mating connector 949-019 or 949-020 and or pigtail must be ordered separately) 1/6
952A-V1-0810-X-X-S Ametek Gemco Linear Displacement Transducer model 952A-V1-0810-X-X-S
''Blue Ox''
A = Analog Version
V1 = 10 to 0 VDC Output
0810 = 81 Inch Stroke
X = Standard Null Zone of 2 Inches
X = Standard Dead Zone of 2.5 Inches
S = Standard Connector. 12 mm 5 Pin Euro connector ( mating connector 949-019 or 949-020 and or pigtail must be ordered separately) 1/6
952CP-0040-X-X-E Ametek Gemco Linear Distance Transducer
952CP = BlueOx Control Pulse Version / Digital Output
0040 = 4 Inch Stroke Length
X = Standard 2 Inch Null Length
X = Standard Dead Zone Length 2 & 1/2 Inches
E = Environmental MS Connector (mating connector and/or pigtail must be ordered separately)
952CP-0080-X-X-E Ametek Gemco Linear Distance Transducer
952CP = BlueOx Control Pulse Version / Digital Output
0080 = 8 Inch Stroke Length
X = Standard 2 Inch Null Length
X = Standard Dead Zone Length 2.5 Inches
E = Environmental MS Connector (mating connector and/or pigtail must be ordered separately)
952CP-0120-X-X-E Ametek Gemco Linear Distance Transducer
952CP = BlueOx Control Pulse Version / Digital Output
0120 = 12 Inch Stroke Length
X = Standard 2 Inch Null Length
X = Standard Dead Zone Length 2 & 1/2 Inches
E = Environmental MS Connector (mating connector and/or pigtail must be ordered separately)
952CP-0267-N2-D5-E Ametek Gemco Linear Distance Transducer model AME-952CP-0267-N2-D5-E
952CP = BlueOx Control Pulse Version / Digital Output
0267 = 26.7 Inch Stroke Length
N2 = 2 Inch Null Length (Standard)
D5 = 5 Inch Dead Zone
E = Environmental MS Connector (mating connector and/or pigtail must be ordered separately)
952CP-0325-X-D5-E Ametek Gemco Linear Distance Transducer
952CP = BlueOx Control Pulse Version / Digital Output
0325 = 32.5 Stroke Length
X = Standard 2 Inch Null Length
D5 = Dead Zone Length 5 Inches
E = Environmental MS Connector (mating connector and/or pigtail must be ordered separately)
952QD-0100-X-X-C6-1000-EF4- Ametek Gemco Linear Displacement Transducer. Series 952 BlueOx
Model 952QD-0100-X-X-C6-1000-EF4-M1-N-X
952QD = Quadrature Version
0100 = 10 Inch Stroke
X = Standard 2.0 Inch Null
X = Standard 2.5 Inch Dead Zone
C6 = Potted Pigtail Assembly by 6 Foot long
1000 = Standard Output Resolution, Cycles per inch
E = Input type '' Sinking'' (typically used with sourcing output type)
F4 = 75 KHz Quadrature Cycle Output Frequency Range
M1 = X1 Quadrature. Output Mode
D = Differntial RS422 Line Driver. TTL compatible
X = no other options
952RS-0030-X-X-C6 Ametek Gemco Linear Displacement Transducer
952RS-0030-X-X-C6
952RS =Digital Version - Start/Stop Pulse
0030 = 3 Inch Stroke Length
X = Standard Null Length of 2 Inches
X = Standard Dead Zone of 2 Inches
C6 = Potted Pigtail Cable assembly by 6 feet long
952RS-0120-X-X-E Ametek Gemco Linear Displacement Transducer
952RS-0120-X-X-E
952RS =Digital Version - Start/Stop Pulse
0120 = 12 Inch Stroke Length
X = Standard Null Length of 2 Inches
X = Standard Dead Zone of 2 Inches
E = Environmental MS Connector. Mating connector and / or pigtail must be ordered separately
952RS-0180-X-X-C6 Ametek Gemco Linear Displacement Transducer
952RS-0180-X-X-C6
952RS =Digital Version - Start/Stop Pulse
0180 = 18 Inch Stroke Length
X = Standard Null Length of 2 Inches
X = Standard Dead Zone of 2 Inches
C6 = Potted Pigtail Cable assembly by 6 feet long
952RS-0360-X-X-E Ametek Gemco Linear Displacement Transducer
952RS-0360-X-X-E
952RS =Digital Version - Start/Stop Pulse
0360 = 36 Inch Stroke Length
X = Standard Null Length of 2 Inches
X = Standard Dead Zone of 2 Inches
E = Environmental MS Connector. Mating connector and / or pigtail must be ordered separately
952VP-0240-X-X-E-E-002 Ametek Gemco Linear Displacement Transducer model 952VP-0300-X-X-E-E-002
''Blue Ox''
VP = Variable Pulse
0300 = 30 Inch Stroke
X = Standard 2 Inch Null Zone
X = Standard 2.5 Inch Dead Zone
E = Environmental MS Connector, Designation T is no longer available
E = External Interrogation
002 - Number of Recirculations
952VP-0300-X-X-E-E-002 Ametek Gemco Linear Displacement Transducer model 952VP-0300-X-X-E-E-002
''Blue Ox''
VP = Variable Pulse
0300 = 30 Inch Stroke
X = Standard 2 Inch Null Zone
X = Standard 2.5 Inch Dead Zone
E = Environmental MS Connector, Designation T is no longer available
E = External Interrogation
002 - Number of Recirculations
952VP-0660-X-X-E-I-001 Ametek Gemco Linear Displacement Transducer model 952VP-0660-X-X-E-I-001
''Blue Ox''
VP = Variable Pulse
0660 = 66 Inch Stroke
X = Standard 2 Inch Null Zone
X = Standard 2.5 Inch Dead Zone
E = Environmental MS Connector
I = Internal Interrogation
001 - Number of Recirculations (standard)
952VP-0710-X-X-E-I-001 Ametek Gemco Linear Displacement Transducer model 952VP-0710-X-X-E-I-001
''Blue Ox''
VP = Variable Pulse
0710 = 71 Inch Stroke
X = Standard 2 Inch Null Zone
X = Standard 2.5 Inch Dead Zone
E = Environmental MS Connector
I = Internal Interrogation
001 - Number of Recirculations (standard)
952VP-0780-X-X-E-E-002 Ametek Gemco Linear Displacement Transducer model 952VP-0780-X-X-E-E-002
''Blue Ox''
VP = Variable Pulse
0780 = 0780 Inch Stroke
X = Standard 2 Inch Null Zone
X = Standard 2.5 Inch Dead Zone
E = Environmental MS Connector, Designation T is no longer available
E = External Interrogation
002 - Number of Recirculations
952VP-0960-N2.5-D5-E-I-001 Ametek Gemco Linear Displacement Transducer model 952VP-0960-N2.5-D5-E-I-001
''Blue Ox''
VP = Variable Pulse
0960 = 96 Inch Stroke
N2.5 = 2.5 Inch Null Zone
D5 = 5 Inch Dead Zone
E = Environmental MS Connector
I = Internal Interrogation
001 - Number of Recirculations ( standard)

952VP-1560-X-X-E-E-002 Ametek Gemco Linear Displacement Transducer model 952VP-1560-X-X-E-E-002
''Blue Ox''
VP = Variable Pulse
1560 = 1560 Inch Stroke
X = Standard 2 Inch Null Zone
X = Standard 2.5 Inch Dead Zone
E = Environmental MS Connector, Designation T is no longer available
E = External Interrogation
002 - Number of Recirculations
952VP-2110-16 Ametek Gemco LDT. BlueOx Variable Pulse LDT for a 2110 Shut Height Monitor. 16 Inch Stroke Length 1/7
952VP-21104 Ametek Gemco Linear Distance Transducer LDT. Blue Ox Variable Pulse with a 4 Inch Stroke
952VP0300//0001 Ametek Gemco LDT, Blue OX, 30 Inch Stroke, Internal Interrogation, Environmental Connector, 6 Recirculations (6LBS) Sr # 18126-AO
953A-C4-0070-X-X-S-X Ametek Gemco Linear Distance Transducer. (LDT) High Resolution (Analog) The 953A is an accurate programmable, non-contact Linear Displacement Transducer in a Rod Style package.Absolute position accurate to 0.01% of the programmable sensing distance. Auto tuning capability with diagnostic LED's
C4= 4 to 20mA Output
0070 = 7 Inch Active Stroke
X = Standard 2 Inch Null Zone
X = Standard Dead Band of 2.5 Inches
S = 5 Pin Micro, 12 mm Euro, Connector
X= No other options
953A-C4-0118-X-X-S-X Ametek Gemco Linear Distance Transducer. (LDT) High Resolution (Analog) The 953A is an accurate programmable, non-contact Linear Displacement Transducer in a Rod Style package.Absolute position accurate to 0.01% of the programmable sensing distance. Auto tuning capability with diagnostic LED's
C4= 4 to 20mA Output
0118 = 11.8 Inches Active Stroke
X = Standard 2 Inch Null Zone
X = Standard Dead Band of 2.5 Inches
S = 5 Pin Micro, 12 mm Euro, Connector
X= No other options
953A-C4-0130-X-X-S-X Ametek Gemco Linear Distance Transducer. (LDT) High Resolution (Analog) The 953A is an accurate programmable, non-contact Linear Displacement Transducer in a Rod Style package.Absolute position accurate to 0.01% of the programmable sensing distance. Auto tuning capability with diagnostic LED's
C4= 4 to 20mA Output
0130 = 13 Inches of Active Stroke
X = Standard 2 Inch Null Zone
X = Standard Dead Band of 2.5 Inches
S = 5 Pin Micro, 12 mm Euro, Connector
X= No other options
953A-C4-0300-X-D2.5-S-X Ametek Gemco Linear Distance Transducer. (LDT)
Model AME-953A-C4-0300-X-D2.5-S-X
High Resolution (Analog) The 953A is an accurate programmable, non-contact Linear Displacement Transducer in a Rod Style package.Absolute position accurate to 0.01% of the programmable sensing distance. Auto tuning capability with diagnostic LED's
C4= 4 to 20mA Output
0300 = 30 Inches of Active Stroke
X = Standard 2 Inch Null Zone
D2.5 = Dead Band of 5 Inches
S = 5 Pin Micro, 12 mm Euro, Connector
X= No other options
953A-C4-0310-X-D5-S-X Ametek Gemco Linear Distance Transducer, LDT
Model AME-953A-C4-0310-X-D5-S-X
High Resolution, Analog The 953A is an accurate programmable, non-contact Linear Displacement Transducer in a Rod Style package.Absolute position accurate to 0.01% of the programmable sensing distance. Auto tuning capability with diagnostic LED's
C4= 4 to 20mA Output
0310 = 31 Inches of Active Stroke
X = Standard 2 Inch Null Zone
D5 = 5 Inch Dead Band
S = 5 Pin Micro, 12 mm Euro, Connector
X= No other options
953A-C4-0460-X-D2.5X-S-X Ametek Gemco Linear Distance Transducer. (LDT)
Model 953A-C4-0460-X-D2.5-S-X
High Resolution (Analog) The 953A is an accurate programmable, non-contact Linear Displacement Transducer in a Rod Style package.Absolute position accurate to 0.01% of the programmable sensing distance. Auto tuning capability with diagnostic LED's
C4= 4 to 20mA Output
0460 = 46 Inches of Active Stroke
X = Standard 2 Inch Null Zone
D2.5 = Dead Band of 5 Inches
S = 5 Pin Micro, 12 mm Euro, Connector
X= No other options
953A-C4-0600-X-D2.5-S-X Ametek Gemco Linear Distance Transducer. (LDT)
Model 953A-C4-0600-X-D2.5-S-X
High Resolution (Analog) The 953A is an accurate programmable, non-contact Linear Displacement Transducer in a Rod Style package.Absolute position accurate to 0.01% of the programmable sensing distance. Auto tuning capability with diagnostic LED's
C4= 4 to 20mA Output
0600 = 60 Inches of Active Stroke
X = Standard 2 Inch Null Zone
D2.5 = Dead Band of 5 Inches
S = 5 Pin Micro, 12 mm Euro, Connector
X= No other options
953A-C4-0700-X-X-S-X Ametek Gemco Linear Distance Transducer. (LDT) High Resolution (Analog) The 953A is an accurate programmable, non-contact Linear Displacement Transducer in a Rod Style package.Absolute position accurate to 0.01% of the programmable sensing distance. Auto tuning capability with diagnostic LED's
C4= 4 to 20mA Output
0700 = 70 Inch Active Stroke
X = Standard 2 Inch Null Zone
X = Standard Dead Band of 2.5 Inches
S = 5 Pin Micro, 12 mm Euro, Connector
X= No other options
953A-C4-0780-X-D5-S-X Ametek Gemco Linear Distance Transducer, LDT
Model AME-953A-C4-0310-X-D5-S-X
High Resolution, Analog The 953A is an accurate programmable, non-contact Linear Displacement Transducer in a Rod Style package.Absolute position accurate to 0.01% of the programmable sensing distance. Auto tuning capability with diagnostic LED's
C4= 4 to 20mA Output
0310 = 31 Inches of Active Stroke
X = Standard 2 Inch Null Zone
D5 = 5 Inch Dead Band
S = 5 Pin Micro, 12 mm Euro, Connector
X= No other options
953A-V0-0060-X-X-M-X Ametek Gemco Linear Displacement Transducer. Series 953 VMAX
Model 953A-V0-0060-X-X-M-X
V0 = 0 to 10 VDC Output
0060 = Stroke 6 Inch Length
X = Standard 2.0 Inch Null Zone
X = Standard Dead Band 2.5 Inch
M = 6 Pin DIN-MTS-D60 compatible option
X = No options
953A-V0-0119-X-D5-C12 Ametek Gemco Linear Displacement Transducer. Series 953 VMAX
Model 953A-V0-0119-X-D5-C12
V0 = 0 to 10 VDC Output
0119 = Stroke 11.9 Inch Length 300 mm
X = Standard 2.0 Inch Null Zone
D5= Standard Dead Band 2.5 Inch
C12 = Integral Cable / Potted Pigtail by 12 Foot Long
953A-V0-0120-X-X-M-X Ametek Gemco Linear Displacement Transducer. Series 953 VMAX
Model 953A-V0-0120-X-X-M-X
V0 = 0 to 10 VDC Output
0120 = Stroke 12 Inch Length
X = Standard 2.0 Inch Null Zone
X = Standard Dead Band 2.5 Inch
M = 6 Pin DIN-MTS-D60 compatible option
X = No options
953A-V0-0180-X-X-C30-X Ametek Gemco Linear Displacement Transducer. Series 953 VMAX
Model 953A-V0-0180-X-X-C30-X
V0 = 0 to 10 VDC Output
0180 = Stroke 18 Inch Length
X = Standard 2.0 Inch Null Zone
X = Standard Dead Band 2.5 Inch
C = Integral Cable Assembly by 30 Feet Long
X = No options
953A-V0-0240-X-X-S-X Ametek Gemco Linear Displacement Transducer. Series 953 VMAX
Model 953A-V0-0240-X-X-S-X
V0 = 0 to 10 VDC Output
0240 = Stroke 24 Inch Length
X = Standard 2.0 Inch Null Zone
X = Standard Dead Band 2.5 Inch
S = 5 Pin Micro, 12 mm Euro Connector
X = No options
953A-V0-0500-X-X-S-X Ametek Gemco Linear Displacement Transducer. Series 953 VMAX
Model 953A-VO-0500-X-X-M-X
VO = 0 to 10 VDC Output
0500 = Stroke 6 Inch Length
X = Standard 2.0 Inch Null Zone
X = Standard Dead Band 2.5 Inch
S = 5 Pin Micro, 12 MM Euro
X = No options
953A-V0-300M-X-D5-C12 Ametek Gemco Linear Displacement Transducer. Series 953 VMAX Metric Stroke and Threads M18 x 1.5 metric threads
Model 953A-V0-300M-X-D5-C12
V0 = 0 to 10 VDC Output
0300M = 300 mm Stroke Length
X = Standard 2.0 Inch Null Zone
D5 = Dead Band5 Inches
C12 = Integral Cable / Potted Pigtail by 12 Foot Long
953A-VO-0900-X-C10-X Ametek Gemco Linear Displacement Transducer. Series 953 VMAX
Model 953A-VO-0900-X-X-C10-X
VO = 0 to 10 VDC Output
0900 = Stroke 90 Inch Length
X = Standard 2.0 Inch Null Zone
X = Standard Dead Band 2.5 Inch
C10 = Integral Cable Assembly by 10 Feet Long
X = No other options
953A-VO-2400-X-X-S-X Ametek Gemco Linear Displacement Transducer. Series 953 VMAX
Model 953A-VO-2400-X-X-S-X
VO = 0 to 10 VDC Output
2400 = 240 Inch = 20 Foot Stroke / 20 Foot Active Travel
X = Standard 2.0 Inch Null Zone
X = Standard Dead Band 2.5 Inch
S = 5 Pin Micro, 12 mm Euro Connector
X = No options
953D-CP-0080-X-X-S-X Ametek Gemco Linear Distance Transducer
VMAX Model 953D-CP-0080-X-X-S-X
The 953 VMAX is an accurate programmable, non-contact LDT in a rod style package. Providing accurate position to 0.01% of the sensing distance. The LDT has a wide power range of 7 to 30 Volts DC @ 1 watt. An auto-tuning capability allowing it to sense a non standard ring magnet adjusting its signal strength accordingly. Diagnostic LED's indicating a good or bad magnet signal
CP = Control Pulse Output
0080 = 8 Inch Active Stroke
X = Standard Null Zone of 2 Inches
X = Standard Dead Band of 2.5 Inches
S = Standard 6 Pin , 12mm Euro Connector
X = No other options
953D-RS-0240.X-X-S-X Ametek Gemco Linear Distance Transducer model 953D-RS-0240.X-X-S-X. (LDT) High Resolution (Digital) The 953D is an accurate programmable, non-contact Linear Displacement Transducer in a Rod Style package.Absolute position accurate to 0.01% of the programmable sensing distance. Auto tuning capability with diagnostic LED's
RS = RS-422 Start/Stop Pulse
0240 = 24 Inch Active Stroke
X = Standard 2 Inch Null Zone
X = Standard Dead Band of 2.5 Inches
S = 5 Pin Micro, 12 mm Euro, Connector
X= No other options
953D-VP-0180-X-X-C5-E-001-X 953D-VP-0180-X-X-C5-E-001-X
9551409 Ametek Gemco Programming Unit. In Line Active Zone Programming Unit
955A-C4-0120-X Ametek Gemco LDT. Series 955A BRIK Gen III is an accurate programmable, auto-tuning, non-contact, Linear Displacement Transducer
C4 = 4 to 20 Ma
0120 = 12 Inch Stroke
X = No options
Null Zone: 3 Inches
Dead Zone: 2 Inches
Repeatability: + or - 0/006 % of Full Stroke
Connector: 5 Pin Micro 12mm Euro
IP67 Enclosure
CE Approval
955A-C4-0200-X Ametek Gemco LDT. Series 955A BRIK Gen III is an accurate programmable, auto-tuning, non-contact, Linear Displacement Transducer
C4 = 4 to 20 Ma
0200 = 20 Inch Stroke
X = No options
Null Zone: 3 Inches
Dead Zone: 2 Inches
Repeatability: + or - 0/006 % of Full Stroke
Connector: 5 Pin Micro 12mm Euro
IP67 Enclosure
CE Approval
955A-C4-0240-X Ametek Gemco LDT. Series 955A BRIK Gen III is an accurate programmable, auto-tuning, non-contact, Linear Displacement Transducer
C4 = 4 to 20 Ma
0240 = 24 Inch Stroke
X = No options
Null Zone: 3 Inches
Dead Zone: 2 Inches
Repeatability: + or - 0/006 % of Full Stroke
Connector: 5 Pin Micro 12mm Euro
IP67 Enclosure
CE Approval
955A-C4-0300-X Ametek Gemco LDT. Series 955A BRIK Gen III is an accurate programmable, auto-tuning, non-contact, Linear Displacement Transducer
C4 = 4 to 20 Ma
0300 = 30 Inch Stroke
X = No options
Null Zone: 3 Inches
Dead Zone: 2 Inches
Repeatability: + or - 0/006 % of Full Stroke
Connector: 5 Pin Micro 12mm Euro
IP67 Enclosure
CE Approval
(6LBS)
955A-V0-018-X Ametek Gemco Linear Displacement Transducer
955A BRIK accurate programmable, non-contact, linear displacement transducer in a economical low profile package. Features auto-tuning capability, an analog output programmable over the entire active stroke length & diagnostic LED's for sensing a good magnet signal
V0 = 0 to 10 Volt DC Output
0180 = 18 Inch Active Travel
X = No other options
955A-V0-0957-E Ametek Gemco Linear Displacement Transducer
955A BRIK accurate programmable, non-contact, linear displacement transducer in a economical low profile package. Features auto-tuning capability, an analog output programmable over the entire active stroke length & diagnostic LED's for sensing a good magnet signal
V0 = 0 to 10 Volt DC Output
0957 = 95.7 Inch Active Travel
E = IP68 Rated Connector for High Humidity Environments
955A-V0-0958-E Ametek Gemco Linear Displacement Transducer
955A BRIK accurate programmable, non-contact, linear displacement transducer in a economical low profile package. Features auto-tuning capability, an analog output programmable over the entire active stroke length & diagnostic LED's for sensing a good magnet signal
V0 = 0 to 10 Volt DC Output
0958 = 95.8 Inch Active Travel
E = IP68 Rated Connector for High Humidity Environments
955ARM18 Ametek Gemco Control Arm by 18 Inches Long. For use with 955A & S, 955DQ & D, 955LC LDT's Female & Male Threaded Ends 1/4-28. Other lengths available @ 3,6,9,12,15,18,22,28'' or a custom length
955ARM6 Ametek Gemco Control Arm by 6 Inches Long. For use with 955A & S, 955DQ & D, 955LC LDT's Female & Male Threaded Ends 1/4-28. Other lengths available @ 3,6,9,12,15,18,22,28'' or a custom lengths
955D-RS-1060-X Ametek Gemco Linear Displacement Transducer model 955D-RS-1600-X
''BRIK Gen III''
Digital Output., RS 422 START/STOP with interrogation Start Sequence
1060 = 160 Inch Stroke
955DQ-0060-E-1000-E-F7-X1-N Ametek Gemco Linear Distance Transducer model 955DQ-0060-E-1000-E-F7-X1-N-D-X
955DQ = BRIK Generation III with direct Quadrature Output.
Auto-Tuning Low Profile Package with LED Diagnostics
0060 = 6 Inch Stroke/ Active Travel
E = Euro 12 Pin, 12mm Connector
1000 = 1000 Cycles per Inch Output Resolution. Maximum internal resolution is .001 Inches. Available range is 0001 to 9999
E = Sinking Type, typically used with sourcing output type
F7 = 250 KHz Quadrature Cycle Output Frequency Range
X1 = X1 Quadrature Output Mode
N = Nonvolatile Zero Offset Storage. Retentive 100,000 storage cycles maximum
D = Differential RS422 Line Driver
X = No Environment options
955LC-C4-0360 Ametek Gemco Linear Displacement Transducer
Model 955LC-C4-0360
Series 955LC Smart BRIK Analog LDT
C4 = 4 to 20mA Output
36 Inch Stroke Length / Active Travel
Absolute position, repeatable to 0.01% of the sensing distance
Quick Disconnect Connector
955LC-VO-0200 Ametek Gemco Linear Displacement Transducer
Model 955LC-VO-0200
Series 955LC Smart BRIK Analog LDT
VO = 0 to 10 Volt DC Output
0200 = 20 Inch Stroke Length / Active Travel
Absolute position, repeatable to 0.01% of the sensing distance
Quick Disconnect Connector
955LC-VO-0360 Ametek Gemco Linear Displacement Transducer
Model 955LC-VO-0360
Series 955LC Smart BRIK Analog LDT
VO = 0 to 10 Volt DC Output
36 Inch Stroke Length / Active Travel
Absolute position, repeatable to 0.01% of the sensing distance
Quick Disconnect Connector
955S-C4-0070 Ametek Gemco Linear Displacement Transducer
955S Smart BRIK accurate programmable, non-contact, linear displacement transducer in a economical low profile package. Features auto-tuning capability, an analog output programmable over the entire active stroke length & diagnostic LED's for sensing a good magnet signal
C4 = 4 to 20 mA Output
0070 = 7 Inch Active Travel
955S-C4-0100 Ametek Gemco Linear Displacement Transducer
955S Smart BRIK accurate programmable, non-contact, linear displacement transducer in a economical low profile package. Features auto-tuning capability, an analog output programmable over the entire active stroke length & diagnostic LED's for sensing a good magnet signal
C4 = 4 to 20 mA Output
0100 = 10 Inch Active Travel
955S-C4-0130 Ametek Gemco Linear Displacement Transducer
955S Smart BRIK accurate programmable, non-contact, linear displacement transducer in a economical low profile package. Features auto-tuning capability, an analog output programmable over the entire active stroke length & diagnostic LED's for sensing a good magnet signal
C4 = 4 to 20 mA Output
0130 = 13 Inch Active Travel
955S-C4-0180 Ametek Gemco Linear Displacement Transducer
955S Smart BRIK accurate programmable, non-contact, linear displacement transducer in a economical low profile package. Features auto-tuning capability, an analog output programmable over the entire active stroke length & diagnostic LED's for sensing a good magnet signal
C4 = 4 to 20 mA Output
0180 = 18 Inch Active Travel
955S-C4-0500 Ametek Gemco Linear Displacement Transducer
955S Smart BRIK accurate programmable, non-contact, linear displacement transducer in a economical low profile package. Features auto-tuning capability, an analog output programmable over the entire active stroke length & diagnostic LED's for sensing a good magnet signal
C4 = 4 to 20 mA Output
0500 = 50 Inch Active Travel
955S-C4-0510 Ametek Gemco Linear Displacement Transducer
955S Smart BRIK accurate programmable, non-contact, linear displacement transducer in a economical low profile package. Features auto-tuning capability, an analog output programmable over the entire active stroke length & diagnostic LED's for sensing a good magnet signal
C4 = 4 to 20 mA Output
0510 = 51 Inch Active Travel
955S-V0-0540 Ametek Gemco Linear Displacement Transducer
955S Smart BRIK accurate programmable, non-contact, linear displacement transducer in a economical low profile package. Features auto-tuning capability, an analog output programmable over the entire active stroke length & diagnostic LED's for sensing a good magnet signal
VO = 0 to 10 Volt DC Output
0540 = 54 Inch Active Travel
955S-V0-0650 Ametek Gemco Linear Displacement Transducer
955S Smart BRIK accurate programmable, non-contact, linear displacement transducer in a economical low profile package. Features auto-tuning capability, an analog output programmable over the entire active stroke length & diagnostic LED's for sensing a good magnet signal
VO = 0 to 10 Volt DC Output
0650 = 65 Inch Active Travel
955S-V0-0820-E Ametek Gemco Linear Displacement Transducer
955S Smart BRIK accurate programmable, non-contact, linear displacement transducer in a economical low profile package. Features auto-tuning capability, an analog output programmable over the entire active stroke length & diagnostic LED's for sensing a good magnet signal
V0 = 0 to 10 Volt DC Output
0820 = 82 Inch Active Travel
E = IP68 Rated Connector for High Humidity Environments
956A-C4-0090-E Ametek Gemco Linear Displacement Transducer
Model 956A-C4-0090-E
956A = BLOK LDT Analog Version
C4 = 4 to 20mA Output
0090 = 9 Inch Active Stroke
E = Wet Environment. Electronics sealed to a IP 68 Rating
Input Voltage 13.5 to 30 VDC
Null Zone 3 Inch
Dead Zone 2 Inch
3 Diagnostic LED's
Standard 5 Pin Micro 12mm Euro Connector
CE Approval
IP68 Enclosure
-20 to 70 Degree C
956A-C4-0130-X Ametek Gemco Linear Displacement Transducer
Model 956A-C4-0130-X
956A = BLOK LDT Analog Version
C4 = 4 to 20mA Output
0130 = 13 Inch Active Stroke
X = No other options
Input Voltage 13.5 to 30 VDC
Null Zone 3 Inch
Dead Zone 2 Inch
3 Diagnostic LED's
Standard 5 Pin Micro 12mm Euro Connector
CE Approval
IP67 Enclosure
-20 to 70 Degree C
956DQ0120E1000EF7X1NDF Ametek Gemco LDT
956DG BLOK Digital Quadrature Output with resolutions up to 9,999 Cycles per Inch
956DQ-0120-E-1000-E-F7-X1-N-D-F
0120 = 12 Inch Stroke Length
E = Euro 12 Pin, 12 mm Connector
1000 = 1000 Cycles per Inch Output Resolution
E = Sinking Input, typically used with sourcing output type
F7 = 250 KHz Quadrature Cycle Output Frequency Range
X1 = X1 quadrature, 1ms update, output mode
N = Non-volatile Aero Output Storage, Retentive 100,000 storage cycles maximum
D = Differential RD422 line driver, TTL compatible
F = Front Metal Rod End, Female
956DQ0120E1000EF7X1NDX Ametek Gemco LDT
956DG BLOK Digital Quadrature Output with resolutions up to 9,999 Cycles per Inch
956DQ-0120-E-1000-E-F7-X1-N-D-X
0120 = 12 Inch Stroke Length
E = Euro 12 Pin, 12 mm Connector
1000 = 1000 Cycles per Inch Output Resolution
E = Sinking Input, typically used with sourcing output type
F7 = 250 KHz Quadrature Cycle Output Frequency Range
X1 = X1 quadrature, 1ms update, output mode
N = Non-volatile Aero Output Storage, Retentive 100,000 storage cycles maximum
D = Differential RD422 line driver, TTL compatible
X = No Options
956S-V0-0060-E Ametek Gemco Linear Distance Transducer
956S Series, Smart BLOK Analog
VO = 0 to 10 VDC Output
0110 = 11 Inch Stroke Length
E = Electronics Sealed to an IP 68 Rating for Wet Environments
956S-VO-0110-E Ametek Gemco Linear Distance Transducer
956S Series, Smart BLOK Analog
VO = 0 to 10 VDC Output
0110 = 11 Inch Stroke Length
E = Electronics Sealed to an IP 68 Rating for Wet Environments
A/H-ARC 18'' X 4 Ametek Gemco Type A/H-ARC Brake System. Includes 4, 18 X 8 Inch Hydraulic Brakes, Hydraulic Actuators, Fluid Reservoir Bleeder, Pre-Assembled Air / Hydraulic Control Panel, 3/4 HP Motor & Compressor, Tubing, Armored Hoses, Fittings and Heavy Duty Brake Fluid. Rated dynamic stopping torque, progressive to 3600 LBS./FT. Specify 230 VDC or 230 / 460 VAC 60 Hz., 3 ph power. Net weight 948 LBS. Prices do not include brake wheels.
A/H-ARC 2-18 Ametek Gemco Type A/H-ARC Brake System. Includes 2, 18 X 8 Inch Hydraulic Brakes, Hydraulic Actuators, Fluid Reservoir Bleeder, Pre-Assembled Air / Hydraulic Control Panel, 3/4 HP Motor & Compressor, Tubing, Armored Hoses, Fittings and Heavy Duty Brake Fluid. Rated dynamic stopping torque, progressive to 3600 LBS./FT. Specify 230 VDC or 230 / 460 VAC 60 Hz., 3 ph power. Net weight 948 LBS. Prices do not include brake wheels.
A/H-ARC1-14 Ametek Gemco Air over Hydraulic, Air Treadle Remote Control Brake System. Qty. 1, 14 Inch Diameter Hydraulic Brake
A/H-ERC Ametek Gemco Type A/H-ERC Conversion System for Type H Systems (no parking feature). Includes one 3/4 HP motor driven compressor assembly, one prepiped and prewired control panel, one two way hydraulic check valve, one installation kit including tubing, fittings and fluid. 230VDC or 460VAC 3PH 60Hz.
A/H-ERC 18'' X 4 Ametek Gemco Type A/H-ERC Brake System, Electric Remote Controlled. Provides Service Braking, Off Power Emergency Braking plus Parking Brakes. Air over hydraulic brake system includes 4, 18 Inch Brake Assemblies, Fluid Reservoir Bleeder, Foot Treadle Valve, Preassembled Air-Over-Hydraulic Control Panel, 3/4 Horsepower Motor & Compressor, Parking Control Switch, Hyd Tubing, Armored Hoses, Fittings & Brake Fluid. 230 VDC or 230 / 460 VAC 60 Hz. Motor controls are in a NEMA 12 enclosure which is mounted on the panel. Panel size 33 Wide X 45 High X 16 Inches Deep. Brake Wheels are not included
A/H-ERC 18'' X 4 W/PRK Ametek Gemco Type A/H-ERC Brake System, Electric Remote Controlled with 4 Brake Parking. Provides Service Braking, Off Power Emergency Braking plus Parking Brakes. Air over hydraulic brake system includes 4, 18 Inch Brake Assemblies, Fluid Reservoir Bleeder, Foot Treadle Valve, Preassembled Air-Over-Hydraulic Control Panel, 3/4 Horsepower Motor & Compressor, Parking Control Switch, Hyd Tubing, Armored Hoses, Fittings & Brake Fluid. 230 VDC or 230 / 460 VAC 60 Hz. Motor controls are in a NEMA 12 enclosure which is mounted on the panel. Panel size 33 Wide X 45 High X 16 Inches Deep. Brake Wheels are not included
A/H-ERC10-1 Ametek Gemco Hydraulic Brake System. Air Over Hydraulic Electric Remote Controlled Single 10 Inch Brake System
A/H-ERC141 Ametek Gemco A/H-ERC System with 1 14 Inch Hydraulic Brake Assembly
A/HM-ARC 18'' X 2 Ametek Gemco Type A/HM-ARC Brake System with Parking. Provides Service Braking, Off Power Emergency Braking plus Parking Brakes. Air over hydraulic brake system includes 2, 18 Inch Brake Assemblies, Fluid Reservoir Bleeder, Foot Treadle Valve, Preassembled Air-Over-Hydraulic Control Panel, 3/4 Horsepower Motor & Compressor, Parking Control Switch, Hyd Tubing, Armored Hoses, Fittings & Brake Fluid. 230 VDC or 230 / 460 VAC 60 Hz. Motor controls are in a NEMA 12 enclosure which is mounted on the panel. Panel size 33 Wide X 45 High X 16 Inches Deep. Brake Wheels are not included
A/HM-ARC 18'' X 4 Ametek Gemco Type A/HM-ARC Brake System with 4 Brake Parking. Provides Service Braking, Off Power Emergency Braking plus Parking Brakes. Air over hydraulic brake system includes 4, 18 Inch Brake Assemblies, Fluid Reservoir Bleeder, Foot Treadle Valve, Preassembled Air-Over-Hydraulic Control Panel, 3/4 Horsepower Motor & Compressor, Parking Control Switch, Hyd Tubing, Armored Hoses, Fittings & Brake Fluid. 230 VDC or 230 / 460 VAC 60 Hz. Motor controls are in a NEMA 12 enclosure which is mounted on the panel. Panel size 33 Wide X 45 High X 16 Inches Deep. Brake Wheels are not included
A/HM-ERC Ametek Gemco Type A/HM-ERC Conversion System for Type HM Systems (with parking feature). Includes one 3/4 HP motor driven compressor assembly, one prepiped and prewired control panel, one two way hydraulic check valve, one installation kit including tubing, fittings and fluid. 230VDC or 460VAC 3PH 60Hz.
A/HM-ERC System Ametek Gemco Type A/HM-ERC System. Qty. 1, 18 X 8 Inch Brake Type HM Brake (with parking brake feature). Includes Brake, Fluid Reservoir Bleeder, Pre-Assembled Air / Hydraulic Control Panel, 3/4 HP Motor Driven Compressor Assembly, Tubing, Hoses, Fittings & Brake Fluid. 230 VDC or 460 VAC 3PH 60Hz Does not require existing brake but does require the existing foot pedal in the crane cab
A/HM-HRC 18X2 Ametek Gemco Air Over Hydraulic Brake System with Parking to provide 3600 FT LBS of Braking Torque, Emergency Braking & 1400 FT LBS of Parking Brake Torque. Includes 2, 18 Inch Brakes, Hydraulic Actuators, Fluid Reservoir Bleeder, Pre-Assembled Air over Hydraulic Panel, 3/4 HP Motor & Compressor, Hydraulic Foot Pedal, Parking Control Switch, Tubing, Hoses, Fittings & Brake Fluid. Brake Wheels are not included.
A000228 Ametek Gemco Valve. Over-Pressure Safety Valve (1LB) CMH000161
A000267 Ametek Gemco Valve. Air Check Valve, 1 Way (1LB) 1658870
A002091 Ametek Gemco Drain Valve for Air Tank (1LB)
A002226 Ametek Gemco Air Pressure Gauge, Back Connection (<1LB)
A0054300 Ametek Gemco Switch for a Series 1025 Switch Assembly
A0054700 Ametek Gemco Button. Button on a 1025D Foot or Palm Operated Switch Assembly. 1 LB Gross
A021857 Ametek Gemco OBSOLETE Moisture Ejection Valve, no longer manufactured. No parts or repair kits are available. Replaced by J107084 (2LBS)
A024912 Ametek Gemco Protection Valve
A032922 Ametek Gemco 2 Way Air Check Valve (<1LB) CMQ000207
A035780 Ametek Gemco Single Air Reservoir
A037051 Ametek Gemco Copper Tubing, 50 Ft 5/16 Inch
A039206 Ametek Gemco RF Valve Seal Kit (1LB)
A039221 Ametek Gemco RG Valve Seal Kit
A045240 Ametek Gemco FG Air Application Valve (3LBS)
A049284 Ametek Gemco Valve, Obsolete see A078880, Push to Release Air Valve, Normally Closed, Parking Bleed Valve (1LB)
A049974 Ametek Gemco Reservoir. Dual Compartment / Split Air Reservoir (20LBS)
A054581 Ametek Gemco Seal Kit 88740
A054582 Ametek Gemco Repair Kit. Valve Seal Kit for the Emergency Relay Valve # 58860 or 71891, 12 Parts, (1LB)
A055980 Ametek Gemco Hydraulic Tubing, 100 FT, Copper
A056301 Ametek Gemco Obsolete FG HRC Hydraulic Remote Controlled Valve see 107047
A064132 Ametek Gemco Air Pressure Regulator. (ISGSAP1267505)
A065112 Ametek Gemco 30 Inch Air Hose (1LB)
A071891 Ametek Gemco Valve. Relay Emergency Valve used on some Air over Hydraulic Brake systems with the parking brake option. Midland Valve modified by Ametek Gemco (5LBS)
A075410 Ametek Gemco Repair Kit for the 58860 Emergency Relay Valve (1LB)
A075422 Ametek Gemco Repair Kit. Obsolete 4/6 for a 98275 Disc Brake Power Cluster. 1 X 8 Pressure Ratio. Includes air piston cup & felt washer on the pneumatic side & secondary seals, main piston, secondary piston, compensating check valve, back-up washer, primary cup & zero residual check valve on the hydraulic side. 7 Inch Dia. (1LB)
A075530 Ametek Gemco Cap on the Emergency Relay Valve (1LB)
A078880 Ametek Gemco Valve, Push to Release Air Valve, Normally Closed, Parking Bleed Valve (1LB)
A088740 Ametek Gemco Air Valve, Push to Release, Normally Closed, Parking Bleed Valve, was A049284 (1LB) ISG CLE SAP 1269786
A100596 Ametek Gemco Check Valve. No longer used or required on the panel per Frank Ernst, Ametek Gemco 11/04
A1502402 Ametek Gemco Gear Assembly. Includes Worm Gear and Hub for mounting onto the cam shaft (1LB)
AD3017 Ametek Gemco Air Reservoir, Single Compartment, 2020 Cubic Inch, 42 Inches Long, 8.2 Inch Dia., Qty. 3 Holes, 3/8 Pipe Thread, (30LBs) Old price
AD35780 Ametek Gemco Reservoir. Single Compartment Air Reservoir
AE56301 Ametek Gemco Obsolete replaced by J107047
AH/ARC Ametek Gemco AH/ARC - Air Over Hydraulic Brake Control System. Includes pre-assembled air-over hydraulic panel J089666 for 230VDC, J070943 3/4 HP 230 VDC Compressor, (4) 18 Inch Hydraulic Brake Assemblies, Actuators, Fluid Reservoir Bleeder, Foot Air Treadle Valve, Low Air Pressure Buzzer, Air Gauge, Tubing, Hoses, Fittings & Wagner Brake Fluid
AH/ERC 1 BRK 10'' Ametek Gemco Air Over Hydraulic Electric Remote Control Brake system with Qty. 1, 10 Inch Brake Assemblies
AH/ERC 4 BRK 10'' Ametek Gemco Air Over Hydraulic Electric Remote Control Brake System with Qty. 4, 10 Inch Brake Assemblies. Includes Brakes, Hydraulic Actuators, Fluid Reservoir Bleeder, Bleeder Switch with Enclosure, Pre-assembled air Over Hydraulic Panel, 3/4 HP Compressor Assembly, Tubing, Hoses, Fittings & Brake Fluid. Includes optional auxiliary cab control via a Foot Operated Air Treadle Valve. 0 to 4000 FT LBS Stopping Torque. Brakes 100 LBS. Ea or 46 Kg. Total Gross 900 LBS. or 400 Kg.
AH/ERC 4 BRK 18'' Ametek Gemco Air Over Hydraulic Electric Remote Control Brake system with Qty. 4, 18 Inch Brake Assemblies.
AH/ERC-10-1 Ametek Gemco A/H ERC Brake System 230VDC with optional cab control and a manual FRB
AH/HM-ERC 2-10X4 Ametek Gemco AH/HM-ERC 2 10X4 Brake System with Two 10 X 4 Inch Hydraulic Brakes. Air Over Hydraulic - Hydraulic Remote Control Brake System with Air Treadle Control. Brake can be controlled by remote control electrically & via a provided Air Treadle. Two 10 Inch Hydraulic Brakes provide infinitely variable progressive brake application for smooth controlled braking. 0 to 2800 LBS. / FT dynamic braking torque. Includes Qty.2, 10 Inch Hydraulic Brake Assemblies, Control Panel with Compressor Motor Controls, Reservoirs and 2, air over hydraulic Power Clusters, Quincy Industrial Compressor Assembly, Fluid Reservoir Bleeder, Pushbutton Switch with Enclosure for operating the bleeder check valve, Air Treadle for Cab Control, 200 Feet of Hydraulic Tubing, 25 Tube Nuts, 6 Tube Unions, 70 Tube Clamps, 70 Tube Bushings, 4 Hose Brackets, 11 Hose Copper Gaskets, 4 30 Inch Armored Flexible Hoses & 3 Gallons of Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703. 10 Inch Brake Weight 161 LBS. Overall brake Width 9 - 5/8 Inch, Brake Height 28 - 1/2 Inch. Please specify AC or DC Voltage. 10 X 4 Inch Brake Wheels are not included
AH/HRC 1, 14X6 Ametek Gemco AH/HRC Brake System with One 14 X 6 Inch Hydraulic Brakes. Air Over Hydraulic - Hydraulic Remote Control Brake System with operator hydraulic control. Brake can be controlled by remote control electrically & via a provided hydraulic foot pedal. One 14 Inch Hydraulic Brakes provide infinitely variable progressive brake application for smooth controlled braking. 0 to 1400 LBS. / FT dynamic braking torque. Includes Qty.1, J002929 14 Inch Hydraulic Brake Assembly, Control Panel with Compressor Motor Controls, Reservoirs and 1, Air Over Hydraulic Power Clusters, J070943 Quincy Industrial Compressor Assembly, Fluid Reservoir Bleeder, Pushbutton Switch with Enclosure for operating the bleeder check valve, J017616 Control Cylinder with J008219 Foot Pedal, 100 Feet of Hydraulic Tubing, J86 Tube Nuts, J49087 Tube Unions, J005137 Tube Clamps, J005137 Tube Bushings, 2 F005780 Hose Brackets, Hose Copper Gaskets, 2 J010160 30 Inch Armored Flexible Hoses & Gallons of Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703. 14 Inch Brake Weight 161 LBS. Overall brake Width 9 - 5/8 Inch, Brake Height 28 - 1/2 Inch. Please specify AC or DC Voltage. 14 X 6 Inch Brake Wheels are not included
AH/HRC 2, 14X6 Ametek Gemco AH/HRC Brake System with Two 14 X 6 Inch Hydraulic Brakes. Air Over Hydraulic - Hydraulic Remote Control Brake System with operator hydraulic control. Brake can be controlled by remote control electrically & via a provided hydraulic foot pedal. Two 14 Inch Hydraulic Brakes provide infinitely variable progressive brake application for smooth controlled braking. 0 to 2800 LBS. / FT dynamic braking torque. Includes Qty.2, J002929 14 Inch Hydraulic Brake Assemblies, Control Panel with Compressor Motor Controls, Reservoirs and 2, Air Over Hydraulic Power Clusters, J070943 Quincy Industrial Compressor Assembly, Fluid Reservoir Bleeder, Pushbutton Switch with Enclosure for operating the bleeder check valve, Control Cylinder with Foot Pedal, 200 Feet of Hydraulic Tubing, 25 Tube Nuts, 6 Tube Unions, 70 Tube Clamps, 70 Tube Bushings, 4 F005780 Hose Brackets, 11 F17 Hose Copper Gaskets, 4 J010160 30 Inch Armored Flexible Hoses & 3 Gallons of Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703. 14 Inch Brake Weight 161 LBS. Overall Brake Width 9 - 5/8 Inch, Brake Height 28 - 1/2 Inch. Please specify AC or DC Voltage. 14 X 6 Inch Brake Wheels are not included
AHM/ERC 2 8x3 Brks & Cab AHM/ ERC system with (2) 8 x 3 brakes and cab control.
Includes the following:
2 each J003205001 8 x 3 TYPE HM brakes (with parking)
1 each J008219002 foot pedal assembly
1 each J017616002 control cylinder
1 each J045767999 operator switch
1 each J07094____ air compressor 3/4 HP
1 each J071030005 tubing installation kit
1 each J073900005 tubing kit, 2 hose w/ 50' tubing
2 each J073903005 tubing kit, 4 hose w/ 200' tubing
1 each J_________ AHM/ ERC panel 1-2 brake system
2 each J107230 right angle tee kit
2 each PSD01801__ FRB unit
AK73 Westinghouse Brake OBSOLETE see CB-75
B10B Ametek Gemco Tach. Obsolete replaced by 04573067 though some modification to the pulley & mounting bracket is required
Brake Monitoring Option Ametek Gemco Brake Monitoring Module. Add on to a new cam box order. Includes: SD0195800 = Longer NEMA 1 Enclosure & Main Shaft, Micro-Adjust Cam, Snap Switch SPDT, Roller Follower, Electronic Pulse Generating Disc & Electronic Pulse Generating Switch
BZ-2RW22-A2 Ametek Gemco Micro Switch, S.P.D.T. BZ-2RW22-A2 Freeport IL Open, Closed & Common Terminals 04537001
BZ2RW822-A2 Ametek Gemco Switch 04537001
C-6131-B Ametek Gemco Bracket. See C0613100 ''L'' Shape Bracket for use with a Type ''K'' 2006, 2 Circuit Switch. 90 Degree, 2 Inches Wide, Qty. 3, Slots 15/32 X 23/32 on 1.75 Inch Centers (2LBS)
C-6132-B Ametek Gemco Bracket. See C0613200 ''L'' Shaped Bracket for use with a Type ''K'' 2006, 4 Circuit Switch (1LB)
C0197400 Ametek Gemco Cover. Cover only for a Series 1980 NEMA 1, 1 to 4 Circuit Cam Box 5/6
C0197500 Ametek Gemco Cover. Cover only for a Series 1980 NEMA 1, 5 to 6 Circuit Cam Box 11/06
C0197700 Ametek Gemco Cover. Cover only for a Series 1980 NEMA 1, 11 Circuit Cam Box
C0198500 Ametek Gemco Cover. Cover only for a Series 1980 NEMA 12, 2 to 4 Circuit Cam Box (4LBS)
C0198600 Ametek Gemco Cover. Cover only for a Series 1980 NEMA 12, 5 to 6 Circuit Cam Box (6LBS)
C0198700 Ametek Gemco Cover. Cover only for a Series 1980 NEMA 12, 7 to 8 Circuit Cam Box (8LBS)
C0198800 Ametek Gemco Cover. Cover only for a Series 1980 NEMA 12, 9 to 12 Circuit Cam Box (10LBS)
C035800 Ametek Gemco Bracket. Side Frame Bracket Stands for new smaller diameter Gate Hoist Cams (August 1993) Required update when old style cams are replaced with new smaller diameter cams. 2 per Cam Box (1LB)
C0358000 Ametek Gemco Bracket. Side Frame Bracket Stands for new smaller diameter Gate Hoist Cams (August 1993) Required update when old style cams are replaced with new smaller diameter cams. 2 per Cam Box (1LB)
C0613100 Ametek Gemco Bracket. ''L'' Shape Bracket for use with a Type ''K'' 2006, 2 Circuit Switch. 90 Degree, 2 Inches Wide, Qty. 3, Slots 15/32 X 23/32 on 1.75 Inch Centers (1LBS)
C0613200 Ametek Gemco Bracket. ''L'' Shaped Bracket for use with a Type ''K'' 2006, 4 Circuit Switch (1LB)
Cast Iron or Bronze Encl Ametek Gemco Cast Bronze Enclosure for NEMA 4 2000 Series Worm Gear Limit Switches, adder
CB-110 Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / solenoid Released, 7 Inch Diameter, AC Voltages, 60 or 50 Hz., Single Phase., 85 Ft LB Continues or 110 FT LB Intermittent, less a 7.00 X 4.25 Inch Brake Wheel. 60 LBS. Gross Reliable design with very few parts. Simple one point torque adjustment. Rugged long life solenoid - tested in more than 2 million operational cycles without electrical failure. Manual brake release with hand pressure on the solenoid arm. Solenoid plunger travel indicator - a mark on the plunger indicates when the brake should be adjusted for lining wear. Simple two-point adjustment for lining wear.
CB-15 Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 4.5 Inch Diameter, AC Voltages, 60 or 50 Hz., Single Phase., 10 Ft LB Continues or 15 FT LB Intermittent, less a 4.50 X 2.75 Inch Brake Wheel E004800. (20LBS) Reliable design with very few parts. Simple one point torque adjustment. Rugged long life solenoid - tested in more than 2 million operational cycles without electrical failure. Manual brake release with hand pressure on the solenoid arm. Solenoid plunger travel indicator - a mark on the plunger indicates when the brake should be adjusted for lining wear. Simple two-point adjustment for lining wear.
CB-160 Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 10 Inch Diameter, Many AC Voltages, 60 or 50 Hz., Single Phase., 160 FT LB Intermittent Duty, 125 FT LB continues Duty, less a 10.00 X 4.25 Inch Brake Wheel E010800. 78 LBS Net. Motor Freight on a skid. Reliable design with very few parts. Simple one point torque adjustment. Rugged long life solenoid - tested in more than 2 million operational cycles without electrical failure. Manual brake release with hand pressure on the solenoid arm. Solenoid plunger travel indicator - a mark on the plunger indicates when the brake should be adjusted for lining wear. Simple two-point adjustment for lining wear
CB-35 Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 5.50 Inch Diameter, AC Voltages, 60 or 50 Hz., Single Phase., 25 Ft LB Continues or 35 FT LB Intermittent, less a 5.50 X 3.25 Inch Brake Wheel E005500. (34LBS) Reliable design with very few parts. Simple one point torque adjustment. Rugged long life solenoid - tested in more than 2 million operational cycles without electrical failure. Manual brake release with hand pressure on the solenoid arm. Solenoid plunger travel indicator - a mark on the plunger indicates when the brake should be adjusted for lining wear. Simple two-point adjustment for lining wear
CB-75 Ametek Gemco Brake Assembly, AC Solenoid, Spring Set / Solenoid Released, 7 Inch Diameter, AC Voltages, 60 & 50 Hz., Single Phase, 50 FT LB Continues or 75 FT LB Intermittent, less a 7.00 X 4.25 Inch Brake Wheel E007500. (60LBS) Reliable design with very few parts. Simple one point torque adjustment. Rugged long life solenoid - tested in more than 2 million operational cycles without electrical failure. Manual brake release with hand pressure on the solenoid arm. Solenoid plunger travel indicator - a mark on the plunger indicates when the brake should be adjusted for lining wear. Simple two-point adjustment for lining wear
CO197500 Ametek Gemco Cover. Cover only for a Series 1980 NEMA , 4 to 6 Circuit Cam Box (4LBS)
Coil TM- 63 Ametek Gemco Coil for a TM-63 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 1 per brake.
Coil TM- 83 Ametek Gemco Coil for a TM-83 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each (25LBS)
Coil TM-1035 Ametek Gemco Coil for a TM-1035 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each (30LBS)
Coil TM-1355 Ametek Gemco Coil for a TM-1355 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each
Coil TM-1665 Ametek Gemco Coil for a TM-1665 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each
Coil TM-1985 Ametek Gemco Coil for a TM-1985 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each 1/8
Coil TM-2311 Ametek Gemco Coil for a TM-2311 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each 3/7
Coil TM-3014 Ametek Gemco Coil for a TM-3014 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each
Coil TM-43 Ametek Gemco Coil for a TM-43 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 1 per brake.
Conversion System Type H Ametek Gemco A/H-ERC Conversion System for Type H Wagner Hydraulic Brake Systems. Converts a Wagner manual brake system to an Air Over Hydraulic Brake System that can be controlled remotely via an electric circuit. This conversion is for Wagner Hydraulic Brake Systems though other hydraulic brake systems could be suitable for this conversion. (system suitability investigation would be required) The Conversion System Includes: One 3/4 HP Motor Driven Compressor Assembly, One Pre- Piped and Pre-Wired Control Panel, One Two-Way Hydraulic Check Valve, One Installation Kit including all the necessary tubing, fittings & fluid. If the existing brake system does not include a Fluid Reservoir Bleeder, it is required, and is at additional cost. This system requires electrical input of 230 Volt DC or 460 Volt AC, 3 Phase, 60 Hz for the compressor and 115 Volt Control on AC Systems. Please specify AC or DC at time of order. Systems are available with the HM parking option at additional cost.
DT-2RV212-A7 Ametek Gemco Switch 04537003
E004022 Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 4.5 Inch Diameter, 460 Volt AC, 60 Hz., Single Phase., 15 FT LB Intermittent, less a 4.50 X 2.75 Inch Brake Wheel E004800. (20LBS)
E004044 Ametek Gemco Resistor for a TM43 Brake Assembly with a shunt wound coil. This is the standard resistor. Not to be used with rectifiers employing a Forcing Scheme. E004045 is used with a Forcing Scheme Rectifier
E004045 Ametek Gemco Resistor. Forcing Resistor for use with a TM-43 Brake Assembly
E004047 Ametek Gemco Brake Shoe & Lining for a TM-43 4.5 Inch Electric Brake, Bonded Non-Asbestos Lining Material. Sold each, 2 per Brake. 70 Degree Arc, 645C555G02 (2LBS)
E004051 Ametek Gemco Coil. Shunt Wound Coil for a TM-43 Brake Assembly. Intermittent Duty, 1 Hour Cycle 80 Volts DC / 1.10 AMPS. Continuous Duty, 8 Hour Cycle 64 Volts DC / 0.88 AMPS. Average Cold Coil Resistance 73 OHMS. Ref # 26 1 coil per brake 645C545G16 Resistors are required in series E004044 / Forcing E004045 (16LBS)
E004054 Ametek Gemco Pin on a CB35 Brake. Ref # 14 3 per brake @ bottom & top of brake shoes 2247C08H01 (<1LB)
E004055 Ametek Gemco Pin on a CB-15 Brake Assembly. Between Link and Lever. Ref. # 8 1 per brake. 2247C08H02 (<1LB)
E004056 Ametek Gemco Pin on a CB15 Brake Assembly. Connects plunger & link. Item Ref. 6. 1 per brake 2247C08H03 (<1LB)
E004059 Ametek Gemco Lever for a CB15 4 & 1/2 Inch Brake Assembly. Lever between plunger link and inner shoe arm. 2247C09H01
E004060 Ametek Gemco Rod. Adjusting Rod on a CB15 4 & 1/2 Inch Brake, 1 per brake. Ref # 17 , 3279B86G01
E004062 Ametek Gemco Link on a CB-15 brake Assembly. Between plunger & lever arm. Item Ref. 7. 1 per brake. 3279B92H01 (1LB)
E004063 Ametek Gemco Spring Seat on a CB15 Brake Assembly. Ref # 10 1 per brake. Old Westinghouse # 3279B94Ho2
E004065 Ametek Gemco Spring, Main Tension on a CB15 Brake Assembly. Ref # 11 1 per brake. Old Westinghouse # 3280B02H01
E004070 Ametek Gemco Bolt. Brake Shoe Bolt for a TM43 or TM63 Brake, 27D7221H04 1/2 - 13 X 3-1/4'' LG STL G2 PLATED HEX HD CAP Ref # 15, 2 per brake (1LB)
E004071 Ametek Gemco Seat/ Plate. Spring Seat / Plate on the Wheel End of a TM43 Brake, Ref. # 9, 318B777H01 (1LB)
E004074 Ametek Gemco Block. Inner Hinge Block on a TM-43 Brake Tie Rod. Ref. #4. 1 per Brake 318B791H01
E004075 Ametek Gemco Release Bushing on a TM43 Brake
E004076 Ametek Gemco Main Spring Seat on a TM43 Brake Assembly
E004077 Ametek Gemco Dust Seal for the Coil on a TM43 Brake Assembly
E004078 Ametek Gemco Spring. Wheel End Spring on a TM-43 Brake Tie Rod Ref. # 11 1 per brake. Recommended spare part 438A070H15 (1LB)
E004079 Ametek Gemco Tension Spring on a TM43 Brake Assembly
E004080 Ametek Gemco Tension Spring on a TM43 Brake Assembly
E004097 Ametek Gemco Tie Rod on a TM43 4 Inch Brake Assembly. Ref #7. 1 per brake. Old Westinghouse 635C104G09
E004098 Ametek Gemco Bushing for a TM43 or TM63 Brake Assembly, 2 per brake
E004101 Ametek Gemco Lining and Rivet Kit on a CB15 Brake Assembly. Linings have 4 countersunk holes for the rivets. Also available undrilled for bonded applications. Old Westinghouse # 3279B95G01 1 kit per brake. recommended spare part (1LB)
E004102 Ametek Gemco Coil for a CB-15 Brake. 460 Volt 60 Hz. Single Phase, 3280B04G03 (1LB)
E004104 Ametek Gemco Coil for a CB-15 Brake. 115 Volt 60 Hz. Single Phase, 3280B04G01 (1LB)
E004105 Ametek Gemco Coil for a CB-15 Brake. 230 Volt 60 Hz. Single Phase, 3280B04G02 (1LB)
E004107 Ametek Gemco Coil for a CB-15 Brake. 200 Volt 60 Hz. Single Phase, 3280B04G17 (1LB)
E004109 Ametek Gemco Solenoid Assembly on a 4.5'' Dia. CB15 Brake Assembly, includes Plunger & Solenoid Guides, 3279B97H01
E004113 Ametek Gemco Shoe with Lining, Inner, for a CB15 Brake, old 2254C28G01
E004114 Ametek Gemco Shoe with Lining, Outer, for a CB15 Brake, old 2254C27G01
E004117 Ametek Gemco Lining & Rivet Kit for a TM43 4.5 Inch Dia. Electric Brake, 1 Pair drilled for with rivets. The rivets are included. Old Westinghouse # 961C691G23. Undrilled linings for bonded application are also available. Just specify undrilled on any order.
E004118 Ametek Gemco Arm. Outer Brake Shoe Arm on a TM-43 Brake. Ref # 16, 1 per brake, 645C544G01
E004119 Ametek Gemco Arm. Inner Brake Shoe Arm on a TM-43 Brake. Ref # 16, 1 per brake, 645C544G02
E004143 Ametek Gemco Block. Wheel End Hinge Block for a TM43 Brake. Ref # 12 1 per brake. 318B787H01
E004153 Ametek Gemco Coil for a TM43 Brake. Series Wound Coil. 32 Amps 1/2 Hour & 26.5 Amps 1 Hour. Resistance 0.181 OHMS.
E004154 Ametek Gemco Coil. Series Coil for a TM-43 Brake Assembly. 26.5 AMPS Intermittent Duty Cycle, 0.287 Ohms Resistance, G645C545G26 (8 LBS)
E004167 Ametek Gemco Coil. Series Coil for a TM-43 Brake Assembly. 12.5 Amps .5 Hour & 10.3 Amps 1 Hour. Resistance 1.18 Ohms, average.. Ref # 26 1 Coil is required on this brake. Old Westinghouse # 645C545G23
E004175 Ametek Gemco Bushing. Neoprene Bushing on a CB-15 or CB-35 Brake. 2 per brake (<1LB)
E004182 Ametek Gemco Series Coil for a TM-43 Brake Assembly. .Item # 26. 936 Ohms Res. 14 AMPS / 1/2 Hour . 11.5 AMPS / 1 Hour. Old Westinghouse # 208C757G16 1 per brake.
E004500 Ametek Gemco Brake Wheel for the TM-43 Brake Assembly, 4.5 Inch Diameter, 3.125'' Face, 1.56 Offset, 2.62'' Hub Length, 2.75 Inch Hub Diameter, 1.625'' Maximum Bore, 9850 Maximum, RPM, Offset Hub Style ( symmetrical hub style also available), Solid Hub with centerline machined. WK2 / LB FT2 .14 Add $ 125.00 to finish hub offset, hub length, bore & key.
E004600999-C- Ametek Gemco Brake Wheel 4.5
E004800 Ametek Gemco Brake Wheel for the CB15 Brake Assembly, 4.5 Inch Diameter, 2.75'' Face, 2.64'' Offset, 2.2'' Hub Length, Solid Hub with center line machined. 1.625'' Maximum Bore, 9850 Maximum RPM, 2247C13H01 Add $125.00 to finish hub, bore & keyway (9LBS)
E005001 Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 5.50 Inch Diameter, 230 VAC, 60 Hz., Single Phase., 35 FT LB Intermittent, less a 5.50 X 3.25 Inch Brake Wheel (29LBS)
E005002 Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 5.50 Inch Diameter, 460 VAC, 60 Hz., Single Phase., 35 FT LB Intermittent, less a 5.50 X 3.25 Inch Brake Wheel (29LBS)
E005003 Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 5.50 Inch Diameter, 575 VAC, 60 Hz., Single Phase., 35 FT LB Intermittent, less a 5.50 X 3.25 Inch Brake Wheel (29LBS)
E005027 Ametek Gemco Pin on a CB35 Brake. Ref # 14 3 per brake @ bottom & top of brake shoes 2247C08H04 (<1LB)
E005028 Ametek Gemco Pin for a CB-35 5 & 1/2 Inch Brake Assembly. Pin connection between vertical link and main lever. 2247C08H05 (<1LB)
E005029 Ametek Gemco Pin on a CB35 Brake Assembly. Connects plunger to link. Item ref. 6. 1 per brake (<1LB)
E005031 Ametek Gemco Pin on a CB-35 Brake. Ref # 15. 1 per brake. 2247C08H16 (<1lb)
E005032 Ametek Gemco Lever for a CB35 5 & 1/2 Inch Brake Assembly. Lever between plunger link and inner shoe arm. Old Westinghouse 2247C09H02
E005033 Ametek Gemco Rod. Adjusting Rod on a CB35 5 & 1/2 Inch Brake, 1 per brake. Ref # 17 , 3279B86G02
E005034 Ametek Gemco Spring Plate on a CB35 Brake, 3280B89H02 Old price
E005035 Ametek Gemco Link for a CB35 5 & 1/2 Inch Brake Assembly. Link between solenoid plunger and top lever. 3279B92H02
E005036 Ametek Gemco Spring Seat, 3279B94H01, CB35 Brake 5.5'' Dia
E005038 Ametek Gemco Spring, 3280B02H02, CB35 Brake 5.5'' Dia
E005039 Ametek Gemco Brake Coil. 460 VAC 60 Hz.for a CB-35 Brake Assembly. 5 & 1/2 Inch Diameter BW. Ref # 2. 3208B04G07 (1LB)
E005044 Ametek Gemco Conduit / Junction Box on a CB15 or 35 Brake, 9510D22G01, 1 per brake, item 3. Does not include Cover # E005095 (<1LB)
E005047 Ametek Gemco Brake Shoe & Lining for a CB35 Brake Assembly. Outer Shoe away from solenoid. Bonded, 2254C27G02 (5LBS)
E005048 Ametek Gemco Brake Shoe & Lining for a CB35 Brake Assembly. Inner Shoe, close to solenoid. Bonded, 247C28G02 (5LBS)
E005049 Ametek Gemco Brake Lining Kit for a CB35 Brake Assembly. 2 Drilled Linings & Push Pins, 3279B95G02 (1LB)
E005050 Ametek Gemco Solenoid Guides for a CB-15 & CB35 Brake Assembly. Brass Ref. # 5. 6753A37H02 (<1LB)
E005051 Ametek Gemco Coil 115 VAC, 60 Hz for a CB35 Brake Assembly, 3280B04H05
E005052 Ametek Gemco Coil 230 Volt 60 Hz, for a CB-35 Brake Assembly, 5.5'', 3280B04G06 4256302
E005055 Ametek Gemco Solenoid Assembly on a CB-35 5.5 Inch Diameter Brake, includes the Plunger & Solenoid Guides No coil. 3279B97H02 (5LBS)
E005057 Ametek Gemco Spring Plate, 3279B90G02, CB35 Brake 5.5'' Dia Replaced by E005034
E005071 Ametek Gemco Plate. Identification plate on a brake
E005095 Ametek Gemco Cover. Conduit / Junction Box Cover on a CB15 or CB35 Brake (<1LB) 1/8
E005101 Ametek Gemco Cover. Conduit / Junction Box Cover on a CB75, CB110 or CB160 Brake (<1LB) 1/8
E005500 Ametek Gemco Brake Wheel, 5.5 Inch Diameter, for the CB35 Brake Assembly, 3.25 Inch Face, 2.62 Inch Offset, 2.62 Inch Hub Length, Solid Hub, 1.625'' Maximum Bore, 8050 Maximum RPM, 2247C15H01, 4205603 (12LBS)
E006000 Ametek Gemco Heavy Duty Spring Set Magnetic Release Shoe Brake Assembly, Model TM-63, Direct Current Clapper Type, 6 Inch Wheel Diameter, with a Shunt Wound Coil. With a Shunt Coil 50 FT LBS @ 1 Hour. A 6 X 3.125 Inch Brake Wheel is not included. Rectifier for AC Voltages are available at additional cost (57LBS)
E006023 Ametek Gemco Brake Shoe & Lining for a TM-63 6 Inch Electric Brake, Bonded Non-Asbestos Lining Material. Sold each, 2 per Brake. 70 Degree Arc, 645C162G02 (2LBS)
E006025 Ametek Gemco Resistor. External resistor forced for a TM-63 Brake Assembly
E006026 Ametek Gemco Coil. Shunt Wound Coil for a TM-63 Brake Assembly. Intermittent Duty, 1 Hour Cycle 80 Volts DC / 1.35 AMPS. Continuous Duty, 8 Hour Cycle 64 Volts DC / 1.08 AMPS. Average Cold Coil Resistance 59.4 OHMS. Ref # 26 1 coil per brake 645C173G16 Resistors are required in series E006024 / Forcing E006025 (18LBS)
E006028 Ametek Gemco Spring Seat / Plate, Wheel End on a TM63 Brake, 318B777H09
E006031 Ametek Gemco Pivot Pin on a TM43 or 63 Brake Assembly, 318B789H01
E006032 Ametek Gemco Block. Inner Hinge Block on a TM-63 Brake Tie Rod. Ref. #4. 1 per Brake 318B791H09
E006033 Ametek Gemco Release Bushing, TM63, 318B792H09
E006034 Ametek Gemco Main Spring Seat / Retainer, TM63, 318B795H09
E006035 Ametek Gemco Dust seal for Coil on a TM63 Brake Assembly
E006036 Ametek Gemco Spring. Wheel End Spring on a TM-63 Brake Tie Rod Ref. # 11 1 per brake. Recommended spare part 438A070H14(1LB)
E006037 Ametek Gemco Main Spring for a TM63 Brake Assembly. Item # 3. 1 per brake. Old Westinghouse # 438A072H14 Recommended spare part.
E006038 Ametek Gemco Tension Spring for a TM63 Brake Assembly. Item # 28. Qty. 1. 2 per brake. 438A11H06 Recommended spare part (<1LB)
E006041 Ametek Gemco Outer Clapper on a TM-63 Brake assembly. Ref. # 25. 1 per brake. Old Westinghouse # 473B337G01
E006045 Ametek Gemco Adjusting Bar, TM63, 473B345H01
E006049 Ametek Gemco Tie Rod on a TM63 6 Inch Brake Assembly. Ref #7. 1 per brake. Old Westinghouse 635C104G01
E006056 Ametek Gemco Outer Shoe Arm & Bushing Assembly on a TM63 Brake Assembly, 1 per brake, 645C120G01
E006058 Ametek Gemco Screw. Adjusting Screw on a TM-63 Brake. Ref # 8, 1 per brake, 3/8 -16 X 1 & 1/2 1/6
E006059 Ametek Gemco Lining & Rivet Kit for a TM63 6 Inch Dia. Electric Brake, 1 Pair, 70 Degrees, 861C691G24
E006060 Ametek Gemco Inner Brake Shoe Arm & Bushing Assembly on a TM63 Brake Assembly, 1 per brake, 645C120G02 Ref # 20
E006061 Ametek Gemco Clapper Arm & Bushing Outer Assembly on a TM63 Brake, 1 per brake, 645C141G01
E006069 Ametek Gemco Block on the Magnet End TM63, 318B788H09
E006070 Ametek Gemco Block. Wheel End Hinge Block on a TM63 Brake. Ref # 12 1 per brake. Old Westinghouse 318B787H09
E006083 Ametek Gemco Coil. Series Coil for a TM-63 Brake Assembly. 1 Coil is required on this brake. 27.5 AMPS 1 Hour Duty, 37.0 AMPS 1/2 Hour Duty, Average Resistance 0 .163 Ohms. Ref # 26 645C173G22 (18LBS)
E006114 Ametek Gemco Switch Kit to complete a Brake Engagement Circuit on a TM63 Brake. Includes Switch, Bracket, Hardware & Instructions. Some brake modification is required This single switch can be wired for a normally open or a normally closed circuit allowing this switch to show a engaged or disengaged brake. One or the other not both
E006500 Ametek Gemco Stock Bore Brake Wheel, 6 Inch Diameter, 3.125'' Face Width, 3'' Offset when measured from the centerline of the face, 3.5'' Hub Length, 2'' Maximum Bore, 3.25'' Hub Diameter, Stock Bore for the TM63 & ET-6NA Brake, (16LBS) 7937A36H Add $ 135.00 to finish the hub offset, length, bore & key. 834D992H15
E007002 Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 7 Inch Diameter, 460 VAC, Single Phase, 75 FT LB Intermittent, less a 7.00 X 4.25 Inch Brake Wheel (60LBS)
E007012 Ametek Gemco Brake Assembly. CB-110 Brake with a 40 Volt AC Coil
E007053 Ametek Gemco Pin on a CB75 & CB110 Brake. Ref # 14 3 per brake @ bottom & top of brake shoes 2247C08H07 (<1LB)
E007054 Ametek Gemco Pin on a CB75 & 110 Brake Assembly. Ref # 8 1 per brake. Old Westinghouse # 224C08H08
E007055 Ametek Gemco Pin on a CB 75 & 110 Brake, Ref #6, Connects plunger to the link, 1 per brake, old 2247C08H09 (<1LB)
E007057 Ametek Gemco Pin 2247C08H18 (<1LB)
E007058 Ametek Gemco Brake Lever on a CB 75 & CB 110 Brake Assembly. Ref. # 9, 1 per brake, old Westinghouse # 2247C09H03
E007059 Ametek Gemco Rod. Adjusting Rod on a CB75 & CB110 7 Inch Brake, 1 per brake. Ref # 17 , 3279B86G03
E007061 Ametek Gemco Link for a CB75 7 Inch Brake Assembly. Link between solenoid plunger and top lever. 3279B92H03 (<1LB)
E007062 Ametek Gemco Link on a CB110 Brake Assembly, 3279B92H04
E007063 Ametek Gemco Spring Seat
E007064 Ametek Gemco Lining 7 Inch for a CB75 or CB110 Brake, undrilled, 3279B95H03, Qty. 1, 2 per brake (<1LB)
E007065 Ametek Gemco Coil for a CB75 Brake, 460VAC, 60 Hz., 3280B04G11 (2LBS)
E007066.1 Ametek Gemco Coil for a CB-110 or CB-160 Brake Assembly. 460 Volt AC, 60 Hz 3280B04G15 4264204 (3LBS)
E007067 Ametek Gemco Link. Shoe Link 9510D14H03
E007073 Ametek Gemco Brake Shoe & Lining for a CB75 or CB110 7'' Diameter Brake Assembly, Outer Shoe. Bonded 2254C27G03 (9LBS)
E007074 Ametek Gemco Brake Shoe & Lining for a CB75 or CB110 7'' Diameter Brake Assembly, Inner Shoe. Bonded 2254C28G03 (9LBS)
E007076 Ametek Gemco Guides. Solenoid Guides for a CB75, 110 or 160 Brake, Ref # 5, Sold Each, 2 per brake, Old Westinghouse 6753A37H03 (1LB)
E007078 Ametek Gemco Lining Kit for a CB75 or CB110 Brake 7 Inch Brake Assembly, 2 Linings & Pins (1LB)
E007080 Ametek Gemco Coil for a CB75 Brake, 115 VAC, 60 Hz., Ref # 2 3280B04G09 (2LBS)
E007081 Ametek Gemco Coil 230 Volt 60 Hz, for a CB-75 Brake Assembly. 7'', 3280B04G10 (2LB)
E007087 Ametek Gemco Coil. 115 Volt for the CB-110 & CB-160 Brake
E007088 Ametek Gemco Coil, 230 Volt AC, 60 Hz., for a CB-110 or CB-160 Brake Assembly. Old Westinghouse # 3280B04G13 4264202
E007091 Ametek Gemco Solenoid Assembly on a CB-110 7 Inch Diameter Brake Assembly, includes the Plunger & Solenoid Guides. No coil. Old Westinghouse # 3279B97H14 4206406
E007112 Ametek Gemco Bushing. Neoprene Bushing on a CB75, 110, 160 Brake, 2 per brake, 3279B96H03 (<1LB) 1/6
E007500 Ametek Gemco Brake Wheel for the CB-75 & CB-110 Brake Assembly. 7 Inch Diameter, 4.25 Inch Face Width, 3.26 Inch Offset when measured from the Centerline of the Face, 3.26 Inch Hub Length, 3.13 Inch Hub Diameter, Maximum Bore 1.875 Inch, Maximum RPM 6325, Solid Hub with the Bore Center Started, No pilot bore. ASTM A 536 Ductile Iron 80-60-03 or 80-55-06
Add $ 145.00 if you want BPI finish machine the Hub Offset, Length, Bore & Keyway (25LBS)
E008022 Ametek Gemco Resistor. External Resistor for a TM-83 Brake with Shunt Wound Coils. 178 Ohm 550 Watt
E008023 Ametek Gemco Resistor Bank. External Forced Resistors, 2, to be used with a control circuit employing a Forcing Scheme. Designed for a faster brake release & setting response time. TM-83 Brake
E008025 Ametek Gemco Brake Shoe & Lining Complete for a TM-83 or ET-8, 8 Inch Diameter Electric Brake Assembly, Qty. 1, 2 per Brake, Ref. # 14, Bonded, Non-Asbestos Material 439C314G01 (3LBS)
E008026 Ametek Gemco Coil. Shunt Wound Coil for a TM-83 Brake Assembly. Intermittent Duty, 1 Hour Cycle 40 Volts DC / 1.28 AMPS. Continuous Duty, 8 Hour Cycle 32 Volts DC / 1.00 AMP. Average Cold Coil Resistance 31.3 OHMS per coil. Ref # 26 2 coils are required per brake, sold each. 637C504G16 Resistors are required in series E008022 / Forcing E008023 (18LBS)
E008027 Ametek Gemco Bushing for the Clapper Arm on a TM83 or TM1035 Brake, 2 per brake, 31D4114H11
E008028 Ametek Gemco Bushing on a TM83 or TM1035 Brake, 12 per brake, 31D4118H04
E008029 Ametek Gemco Stop Pin on a TM83 or TM1035 Brake, 318B571H03
E008030 Ametek Gemco Clapper on a TM-83 Brake Assembly. ref. # 25. 1 per brake. Old Westinghouse # 318B634G01
E008031 Ametek Gemco Spring Seat. Wheel End Spring Seat on a TM-83 & TM-1035 Brake. Ref # 11 1 per brake. Old Westinghouse # 318B777H02
E008032 Ametek Gemco Spring Clip on a TM-83 Brake Assembly. Ref. # 27. 2 per brake. Old Westinghouse # 318B778H02
E008034 Ametek Gemco Block. Inner Hinge Block on a TM-83 Brake Tie Rod. Ref # 4. 1 per Brake 318B791H02
E008035 Ametek Gemco Adjusting Screw on a TM83 & TM1035 Brake Assembly, 1 per brake, 318B793H02
E008036 Ametek Gemco Stop for a TM83 & TM1035 Brake. Old Westinghouse # 318B794H02
E008037 Ametek Gemco Main Spring Seat / Spring Retainer for a TM-83 Brake Assembly. Ref # 2. 1 per brake. 318B795H02 Old price
E008038 Ametek Gemco Dust Seal for the Coil on a TM83 Brake Assembly, 1 per brake, 318B917H02
E008039 Ametek Gemco Main Spring on a TM83 Brake Assembly, Ref. # 8, 1 per brake, a recommended spare part, 438A072H13
E008040 Ametek Gemco Spring. Tension Spring on a TM83 Brake, 438A411H04
E008041 Ametek Gemco Adjusting Screw Block on a TM83 Brake Assembly, 1 per brake, 438A502H01
E008042 Ametek Gemco Outer Brake Shoe Arms on a TM 83 Brake Assembly. 1 Pair per Brake with bushings. 439C319G03
E008043 Ametek Gemco Arm. Now E008060 Inner Brake Shoe Arm on a TM83 Brake. Ref item # 21. 1 per brake. Old Westinghouse # 439C319G04
E008045 Ametek Gemco Clapper Arm on a TM-83 Brake Assembly. Ref. # 24 1 per brake. Old Westinghouse # 439C329G03
E008049 Ametek Gemco Tie Rod on a TM-83 Brake Assembly. Ref. # 6. 1 per brake. 635C104G02
E008053 Ametek Gemco Series Coil for a TM-83 Brake Assembly. 1 Coils is required on this brake. 25 Coil Amps one hour. 36.5 Coil amps half hour. Average resistance 0.086 Ohms. Ref # 26
E008057 Ametek Gemco Lining & Rivet Kit for a TM83 Electric Brake Assembly, 1 Pair, 8 Inch Diameter, 816C691G16
E008059 Ametek Gemco Base for TM83, 439C330G01
E008060 Ametek Gemco Arm. Inner Brake Shoe Arm on a TM83 Brake. Ref item # 21. 1 per brake. Includes bushings. 439C319G02 Old price
E008061 Ametek Gemco Clapper & Arm on a TM 83 Brake Assembly. 1 per brake. 439C324G01
E008067 Ametek Gemco Hinge Block on the Magnet End on a TM-1035 Brake, 469B671H02
E008068 Ametek Gemco Hinge Block. Wheel End Hinge Block on a TM-83 & TM-1035 Brake. Ref # 12 1 per brake. 318B787H03
E008075 Ametek Gemco Lead Wire for TM-43 to TM-1665 Brake Coils. Shunt wound brake coils (<1LB)
E008085 Ametek Gemco Series Coil for a TM-83 Brake Assembly. 1 Coils is required on this brake. 25 Coil Amps one hour. 36.5 Coil amps half hour. Average resistance 0.086 Ohms. Ref # 26
E008093 Ametek Gemco Hand Release Assembly for a TM83 Brake Old price
E008121 Ametek Gemco Switch Kit to complete a Brake Engagement Circuit on a TM83 Brake. Includes Switch, Bracket, Hardware & Instructions. Some brake modification is required This single switch can be wired for a normally open or a normally closed circuit allowing this switch to show a engaged or disengaged brake. One or the other not both
E008199 Ametek Gemco Pin. Base Pin Assembly for a ET-10 Brake. Includes 2 retaining rings Old price
E008500 Ametek Gemco Brake Wheel, 8 Inch Diameter with a 3.25 Inch Face Width. For the TM-83 & ET-8 Brakes, Stock Bore (25LBS)
E010044 Ametek Gemco Resistor for a TM-1035 Brake Assembly 3/7
E010045 Ametek Gemco Resistor. External resistor forced for a TM-1035 Brake Assembly. With taps set as specified on Ametek data sheet (5LBS)
E010047 Ametek Gemco Brake Shoe & Lining Complete for a TM-1035 or ET-10, 10 Inch Diameter Electric Brake Assembly, Qty. 1, 2 per Brake, Ref. # 14, Non-Asbestos Bonded Lining Material 635C292G01 (5LBS)
E010049 Ametek Gemco Shunt Coil for a TM-1035 Brake Assembly. 2 Coils is required on this brake. 32 Volts per coil continuous duty, 40 Volts per coil intermittent duty, average resistance 24 Ohms. Cost per coil brake requires 2 coils connected in series. Ref # 26 Old Westinghouse # 635C328G16
E010054 Ametek Gemco Pin on a CB160 Brake. Ref # 14 3 per brake @ bottom & top of brake shoes 2247C08H10 (<1LB)
E010055 Ametek Gemco Pin on a CB160 Brake Assembly, Item Ref. 8 1 per brake Connects top of link to brake lever 2247C08H11 (<1LB)
E010056 Ametek Gemco Pin on a CB160 Brake Assembly, Item Ref. 6. 1 per brake Connects plunger to link 2247C08H12 (<1LB)
E010058 Ametek Gemco Pin 2247C08H20
E010059 Ametek Gemco Lever 2247C09H04
E010062 Ametek Gemco Link on a CB160 Brake Assembly, 3279B2H05
E010064 Ametek Gemco Spring. Main Spring on a CB160 Brake Assembly. Ref # 11 1 per brake. 3280B01H01 (1LB)
E010068 Ametek Gemco Base for a CB-160 Brake Assembly. Ref. # 1 1 per brake 9510D16H04
E010069 Ametek Gemco Conduit / Junction Box on a CB75, 110 or 160 Brake, 9510D19G01, 1 per brake, item 3. Does not include Cover # E005101 (<1LB)
E010070 Ametek Gemco Bolt. Brake Shoe Bolt Assembly on a TM-83, TM-1035 & ET-10 Brake. Ref. # 16. 2 per brake. 27D7221H14
E010072 Ametek Gemco Pin. Pivot Pin for a TM83 or 1035 Brake, Item Ref # 19, 4 per brake, 318B789H03 (<1LB)
E010073 Ametek Gemco Pin. Tension Spring Pin on a TM83 or 1035 Brake Assembly, 438A411H03 (1LB)
E010074 Ametek Gemco Block. Inner Hinge Block on a TM-1035 Brake Tie Rod. Ref. #4. 1 per Brake 318B791H03
E010075 Ametek Gemco Bushing. Release Bushing on a TM-1035 Brake. Ref # 5 1 per brake. 318B792H02
E010076 Ametek Gemco Main Spring Seat / Spring Retainer for a TM-1035 Brake Assembly. Ref # 2. 1 per brake. 318B795H03
E010077 Ametek Gemco Dust Seal for the Coil on a TM-1035. Old Westinghouse # 318B917H03
E010078 Ametek Gemco Clapper on a TM-1035 Brake Assembly. Ref # 25. 1 per brake. 318B988G01
E010079 Ametek Gemco Spring. Wheel End Spring on a TM-83 & 1035 Brake Tie Rod. Ref. # 10. 1 per brake. 438A070H13. Recommended spare part (1LB)
E010080 Ametek Gemco Main Spring on a TM1035 brake. Ref # 3. 1 per brake. Recommended spare part. 438A072H11
E010083 Ametek Gemco Adjusting Screw Block on a TM1035 Brake. Ref # 7. 1 per brake. 438A217H01
E010085 Ametek Gemco Spring. Tension Spring on a TM-1035 Brake, Ref. # 28. 2 per brake. Recommended spare part 438A411H03 (1LB)
E010086 Ametek Gemco Tie Rod on a TM1035 10 Inch Brake Assembly. Ref # 6. 1 per brake. 635C104G03
E010096 Ametek Gemco Solenoid Guide, same as E007076, for a CB110 or 160 Brake Assembly
E010098 Ametek Gemco Rod. Adjusting Rod on a CB160 10 Inch Brake, 1 per brake. Ref # 17 , 3279B86G04
E010103 Ametek Gemco Solenoid Assembly on a 10.00'' Dia. CB160 Brake Assembly, includes the Plunger &
Solenoid Guides, 3279B97H05
(8LBS)
E010106 Ametek Gemco Shoe & Lining. Brake Shoe & Lining, Inner Shoe for a CB160 10 Inch Electric Brake. 2254C28G04
E010107 Ametek Gemco Shoe & Lining. Brake Shoe & Lining, Outer Shoe for a CB160 10 Inch Electric Brake. 2254C27G04
E010108 Ametek Gemco Lining & Rivet Kit for a CB160 Brake, ( Drilled Lining with required Push Pins) 3279B95G04
E010109 Ametek Gemco Coil. Series Coil for a TM-1035 Brake Assembly. 2 Coils per brake assembly. 39.00 AMPS per coil continuous duty / 130 FT LB, 54 AMPS per coil intermittent duty / 200 Ft LB, average resistance.209 Ohms. Cost per coil brake requires 2 coils connected in series. Ref # 26 Old Westinghouse # 635C328G22
E010109002 Ametek Gemco 13 Inch Brake with E0109002 Coils
E010111 Ametek Gemco Coil. Series Coil for a TM-1035 Brake Assembly. 20.00 AMPS per coil continuous duty @ 130 FT LB, 27.5 AMPS per coil intermittent duty @ 200 FT LB. Average resistance .209 Ohms. 2 Coils per brake, cost per coil, coils are connected in series. Ref # 26 Old Westinghouse # 635C328G20
E010114 Ametek Gemco Lining Kit, pair of drilled linings & fasteners for a TM1035, 10 Inch Diameter Brake, 861C691G17, 104-3445D ( 8 holes 10-10 Rivet Qty 18 )
E010115 Ametek Gemco Outer Brake Shoe Arm on a TM-1035 Brake Assembly.Item 17. 635C306G01, 1 per brake.
E010116 Ametek Gemco Base Assembly for a TM-1035 brake assembly. Item 18. 1 per brake 635C300G01
E010117 Ametek Gemco Arm. Inner Brake Shoe Arm on a TM-1035 Brake Assembly. Item 21. 635C306G02, 1 per brake
E010118 Ametek Gemco Clapper & Arm for a TM1035 Brake. 1 per brake. Ref # 22. 635C317G01
E010119 Ametek Gemco Clapper Arm on a TM-1035 Brake Assembly. Ref # 24. 1 per brake. 635C308G01
E010131 Ametek Gemco Actuator. Hydraulic Actuator for a ETH10 Brake Assembly. Actuator for cab control. 2 to 4 Weeks 11/04
E010165 Ametek Gemco Coil. Series Coil for a TM-1035 Brake Assembly. 75 Amps per Coil 1/2 Hour Rating. 55 Amps per Coil 1 Hour Rating. Resistance 0.0262 Ohms per Coil. Sold each / 2 coils per brake
E010193 Ametek Gemco Actuating Cylinder for a Electro-Hydraulic Brake. ETH-8 & ETH-10, H4-F-N 2.0'' bore 1'' Stroke, 1'' rod, #4 Rod End, H4-F-N2.0X-1.00X1.00XXS13 Old price
E010237 Ametek Gemco Switch Kit to complete a Brake Engagement Circuit on a TM1035 Brake. Includes Switch, Bracket, Hardware & Instructions. Some brake modification is required This single switch can be wired for a normally open or a normally closed circuit allowing this switch to show a engaged or disengaged brake. One or the other not both
E010266 Ametek Gemco Spring. Main Spring on a ET-10 Brake
E010286 Ametek Gemco Self Adjust Assembly Kit for an ET10 Brake
E010309 Ametek Gemco Tie Rod Assembly for an ET-10 Brake
E010326 Ametek Gemco Rectifier Assembly for a TM-43 through TM-1985 Brake Assembly. A NEMA 4 Enclosure is supplied. 16.0'' H X 14.00'' W X 8.0'' D. An open chassis unit is available at less cost. The following AC input voltages are available 380, 440, 550 600. Please specify one voltage at time of order though the panel can be connected for the other voltages (54LBS)
E010327 Ametek Gemco Rectifier Assembly for a TM-43 through TM-1985 Brake Assembly. Open chassis design without enclosure. A NEMA 4 enclosure is available at additional cost. The following AC input voltages are available 380, 440, 550 600. Please specify one voltage at time of order though the panel can be connected for the other voltages (30LBS)
E010500 Ametek Gemco Brake Wheel, 10 Inch Diameter for the TM-1035 Brake, Stock Bore (40LBS)
E010622 Ametek Gemco Resistor External for a TM-1665 Brake Assembly, Old Westinghouse 47D0146G09
Ohms resistance required in line for 250 VDC 37.7 Ohms / 4.7 Amp
E010800 Ametek Gemco Brake Wheel for the CB-160 Brake Assembly. 10 Inch Diameter, 4.25 Inch Face Width, 4.26 Inch Offset when measured from the Centerline of the Face, 3.38 Inch Hub Length, 3.75 Inch Hub Diameter, Maximum Bore 2.25 Inch, Maximum RPM 4425, Solid Hub with the Bore Center Started, No pilot bore. ASTM A 536 Ductile Iron 80-60-03 or 80-55-06
Add $ 165.00 if you want BPI finish machine the Hub Offset, Length, Bore & Keyway
E011500 Ametek Gemco Brake Wheel, 11 Inch Diameter for the ET-11 Brake, Stock Bore (45LBS)
E013022 Ametek Gemco Resistor External for a TM-1355 Brake Assembly. STD 110.8 OHM 650 Watt. 250 VDC without discharge resistor.
E013023 Ametek Gemco Forcing Resistor for a TM-1355 Brake Assembly. 423A299G03
E013025 Ametek Gemco Brake Shoe & Lining Complete for a TM1355 or ET13, 13 Inch Diameter Electric Brake Assembly, Qty. 1, 2 per Brake, Ref. # 14, Bonded, Non-Asbestos Material 439C201G01 (12LBS)
E013026 Ametek Gemco Coil. Shunt Wound Coil for a TM-1355 Brake Assembly. 32 Volts per coil continuous duty, 40 Volts per coil intermittent duty, average resistance per coil 19 Ohms. Cost per coil, brake requires 2 coils connected in series. Ref. # 26 637C384G16
E013027 Ametek Gemco Bushing for a TM1355 Brake. Qty. 1, 6 per brake. 31D4114H12 (1LB)
E013028 Ametek Gemco Bushing for a TM1355 Brake. Qty. 1, 8 per brake. Ref # 19. 31D4118H06 (1LB)
E013029 Ametek Gemco Clapper on a TM-1355 Brake Assembly. Ref. # 25. 1 per brake. 318B560G01
E013031 Ametek Gemco Seat. Wheel End Spring Seat on a TM1355 Brake assembly, 1 per Brake, 318B777H04
E013032 Ametek Gemco Spring Clip on a TM-1355 Brake Assembly. Ref # 27 2 per brake. 318B778H04 (1LB)
E013033 Ametek Gemco Replaced by E013125
E013034 Ametek Gemco Pin. Pivot Pin used on the TM1355 Brake. Sold each, 4 per brake. 318B789H04 (2LB)
E013035 Ametek Gemco Pin. Tension Spring Pin on a TM-1335 Brake Assembly. Ref # 29 1 per brake. 318B790H04 (1LB)
E013036 Ametek Gemco Block. Inner Hinge Block on a TM-1355 Brake Tie Rod. Ref. #4. 1 per Brake 318B791H04
E013037 Ametek Gemco Release Bushing on a TM1355 & TM1665 Brake Assembly, 1 per Brake, 318B792H04
E013038 Ametek Gemco Stop for a TM1355 & TM1665 Brake. 318B794H04 9/6 (<1LB)
E013039 Ametek Gemco Main Spring Seat / Retainer on a TM1355 Brake Assembly, 1 per Brake, 318B795H04
E013040 Ametek Gemco Seal. Dust Seal for coil on a TM-1355 Brake Assembly. 1 per brake. 318B917H04 (1LB)
E013041 Ametek Gemco Spring. Wheel End Spring on a TM1355 Brake Tie Rod. Ref No. 10 1 per Brake Recommended Spare Part 438A070H09 (2LBS)
E013042 Ametek Gemco Spring. Main Spring for a TM1355 13 Inch Brake, Coil End, 1 per Brake, 438A072H09
E013044 Ametek Gemco Spring. Tension Spring on a TM1355 & TM1665 Brake, 438A411H05 (1LB)
E013045 Ametek Gemco Adjusting Screw Block on a TM1355 Brake. Ref # 7. 1 per brake. 438A456H01
E013051 Ametek Gemco Bracket. Magnet Travel Equalizer Bracket on a TM-1355 Brake
E013052 Ametek Gemco Tie Rod for a TM1355 13 Inch Brake. Ref. #6, 1 per Brake. 861C691G18
E013053 Ametek Gemco Brake Shoe Bolt on a TM1355, 2 per Brake, 24D6387G04. Item 3
E013055 Ametek Gemco Lining Kit, pair of drilled & countersunk linings with fasteners for a TM1355, 13 Inch Diameter Brake. 861C691G18 (3LBS)
E013056 Ametek Gemco Clapper Arm on a TM-1355 Brake Assembly. Ref. # 24. 1 per brake. 439C203G01
E013058 Ametek Gemco Coil. Series Coil for a TM13 Brake, 2 per brake, sold each, 637C551G16, 608 Mill Motor, 0.0358 Ohms Resistance Average, 85 Amps 1/2 Hour, 63 Amps 1 Hour (60 LBS)
E013059 Ametek Gemco Coil. Series Coil for a TM13 Brake, 2 per brake, sold each, 637C551G17, 606 Mill Motor, Ohms Resistance Average, Amps 1/2 Hour, Amps 1 Hour (60 LBS)
E013064 Ametek Gemco Arm. Outer Brake Shoe Arm on a TM-1355 Brake Assembly. Ref. # 17. 1 per brake. 439C192G05
E013066 Ametek Gemco Base on a TM-1355 Brake Assembly. Ref. #18. 1 per brake. 439C204G01
E013067 Ametek Gemco Inner Brake Shoe Arm on a TM-1355 Brake Assembly. Ref. #21. 1 per brake. old Westinghouse # 439C192G06
E013068 Ametek Gemco Clapper & Arm for a TM1355 Brake. 1 per brake. Ref # 22. 489C202G01
E013073 Ametek Gemco Spring Clip on a TM1355 Brake. Hand Release. 1 per brake. Old Westinghouse # 450A574H03 (1LB)
E013098 Ametek Gemco Coil. Series Wound Coil for a TM-1355 Brake. 637C551G23, 54 AMPS 1/2 Hour Rating, 40 AMPS 1 Hour Rating, .081 OHMS per coil, 2 per brake, sold each
E013125 Ametek Gemco Hinge Block on the Magnet End of a TM1355 Brake, 1 per Brake, 318B788H04
E013146 Ametek Gemco Switch Kit to complete a Brake Engagement Circuit on a TM1355 Brake. Includes Switch, Bracket, Hardware & Instructions. Some brake modification is required This single switch can be wired for a normally open or a normally closed circuit allowing this switch to show a engaged or disengaged brake. One or the other not both
E013194 Ametek Gemco Base for a ET13 Brake Assembly. item 1
E013214 Ametek Gemco Main Spring on a ET-13 Brake E013214 & 04581104. Item 9A
E013225 Ametek Gemco Arm. Inner Shoe Arm on a ET-13 Brake. 1 Pair. Item 6
E013228 Ametek Gemco Tie Rod Assembly for a ETH13EB50 Brake. Item 5
E013229 Ametek Gemco Force Arm Assembly on a ET-13 Brake. Item 7
E013231 Ametek Gemco Pin Kit for a ET-13 Brake. Includes Base Pins and Top Pins with Retaining Rings. Item 10
E013240 Ametek Gemco Tie Rod. Self Adjust Tie Rod Assembly on a ET-13 Brake with the Self Adjust Option. Item 5A 4/7
E013500 Ametek Gemco Stock Bore Brake Wheel, 13 Inch Diameter, for the TM-1355 Brake Assembly, 5.75'' Face Width, 5.375'' Offset when measured from the centerline of the face, 5.00'' Hub Length Add $ 185.00 if you want BPI to finish machine the Hub Offset, Hub Length, Bore & Keyway (100LBS)
E013513 Ametek Gemco Brake Wheel 13 Inch Diameter with a hub length bore & keyway for an 808 Mill Motor with the AISE Standard Offset
E014500 Ametek Gemco Brake Wheel 14 Inch Diameter. Pilot Bore, TM & ET Brakes
E016022 Ametek Gemco Series Resistor for a TM-1665 Brake Assembly with Shunt Wound Coils. Old Westinghouse Part # 423A298G04 51 OHMS 250 VDC
E016023 Ametek Gemco Resistor. External resistor forced for a TM-1665 Brake Assembly. With taps set as specified on Ametek data sheet (5LBS)
E016025 Ametek Gemco Brake Shoe & Lining Complete for a TM-1665 or ET-16, 16 Inch Diameter Electric Brake Assembly, Qty. 1, 2 per Brake, Ref. # 14, Non-Asbestos Material Bonded to the Brake Shoe 635C227G01 (31LBS)
E0160251 Ametek Gemco Brake Shoe & Lining Complete, Bonded, for a TM1655 or ET16, 16 Inch Diameter Electric Brake Assembly, Qty. 1, 2 per Brake, 635C227G01
E016026 Ametek Gemco Shunt Coil for a TM-1665 Brake Assembly. 32 Volts per coil continuous duty, 40 Volts per coil intermittent duty, average resistance 8.8 Ohms. Cost is per coil brake requires 2 coils connected in series. Ref # 26 635C247G17
E016027 Ametek Gemco Bolt. Brake shoe Bolt on a TM1655 & ET-16 Brake.Includes Bolt, Nut & Pin. Ref item 16. 2 per brake, 24D6387G03 (2LBS)
E016028 Ametek Gemco Pin on a TM1665 Brake, 1 per Brake, 318B571H05
E016030 Ametek Gemco Spring Clip on a TM-1665 Brake Assembly. Ref # 27 2 per brake. 318B778H05
E016031 Ametek Gemco Block. Wheel End Hinge Block on a Old TM1355 Brake Assembly, 1 per Brake, 318B787H05. New Style Brake uses a E016205
E016033 Ametek Gemco Pivot Pin on a TM1665 Brake Assembly. Ref. # 20, 4 per brake. 318B789H05
E016034 Ametek Gemco Pin. Tension Spring Pin on a TM-1665 Brake Assembly. Ref # 29 1 per brake. 318B790H05 (<1LB)
E016035 Ametek Gemco Block. Inner Hinge Block on a TM-1665 Brake Tie Rod. Ref. #4. 1 per Brake, 318B791H05
E016036 Ametek Gemco Screw, Adjusting Screw on a TM1355 & 1665 Brake, 1 per Brake, 318B793H04 (1LB)
E016038 Ametek Gemco Seal. Dust Seal for coil on a TM-1655 Brake Assembly. 1 per brake. 318B917H05 (1LB)
E016039 Ametek Gemco Spring. Main Spring for a TM-1665 16 Inch Brake, Coil End, 1 per Brake, Recommended Spare Part 438A072H07
E016040 Ametek Gemco Adjusting Screw Block on a TM1665 Brake Tie Rod. 438A352H01
E016050 Ametek Gemco Clapper on a TM-1665 Brake Assembly. Ref #25. 1 per brake. 318B907G01
E016051 Ametek Gemco Base on a TM-1665 Brake assembly. Ref. #18. 1 per brake. Old Westinghouse # 635C235G01
E016052 Ametek Gemco Clapper & Arm on a TM-1665 Brake Assembly. Ref. #22. 1 per brake. Old Westinghouse #635C236G01
E016053 Ametek Gemco Lining Kit, pair of linings & fasteners for a TM1655, 16 Inch Diameter Brake old 861C691G19. New brakes use bonded linings. 7 LBS Gross
E016054 Ametek Gemco Coil. Shunt Coil, Special Shunt Coil for a TM16 Brake, 2 per brake, sold each, 637C530G16, 808 / 610 Mill Motors, 0.0195 Ohms Resistance Average, 90 Volts Intermittent, 1 Hour / 125 Volts Continues Duty Cycle, 8 Hour. Specifications are for a single coil (100LBS) 7/7
E016055 Ametek Gemco Series Coil for a TM-1665 Brake. Quoted each, 2 per brake. It is recommended that Series Coils are replaced in pairs. 637C530G19 7/7
E016060 Ametek Gemco Outer Brake Shoe Arm with Bushings on a TM1665 Brake. Ref. # 17. 1 per brake. 635C240G01
E016061 Ametek Gemco Inner Brake Shoe Arm with Bushings on a TM1665 Brake. Ref. #21. 1 per brake. 635C240G02
E016062 Ametek Gemco Eyebolt, part of Hand Release Assembly on a TM-1665 Brake
E016063 Ametek Gemco Clapper Arm on a TM-1665 Brake Assembly. Ref. #24. 1 per brake. Old Westinghouse #635C238G01
E016064 Ametek Gemco Handle, part of Hand Release assembly on a TM1665 Brake
E016065 Ametek Gemco Outer Block, part of the Hand Release Assembly on a TM-1665 Brake. Welded in place.
E016073 Ametek Gemco Hinge Block, Magnet End on a TM1665 Brake Assembly,
E016089 Ametek Gemco Actuator. Hydraulic Override Cylinder on a ETH-14 Brake Assembly. Slave cylinder for cab operation.
E016105 Ametek Gemco Tie Rod Assembly for a TM-1665 Brake. New larger diameter tie-rod completely populated with all components for installation on an older brake. Includes items 1 thru 6, 10 thru 12 and miscellaneous hardware.
E016108999 Ametek Gemco Hydraulic Actuator on a ETH-16 Thruster Brake with Slave Cylinder
E016200 Ametek Gemco Tie Rod on a TM1665 16 Inch Brake Assembly. Ref # 6. 1 per brake. Old Westinghouse 635C104G05
E016203 Ametek Gemco Wheel End Spring Seat on a TM1665 Brake Assembly, 1 per Brake, 318B777H05
E016205 Ametek Gemco Hinge Block, Wheel End Hinge Block on a TM1355 or TM-1665 Brake, 1 per Brake, new style 1/6
E016206 Ametek Gemco Main Spring Seat on a TM1665 Brake Assembly, 1 per Brake, 318B795H05
E016207 Ametek Gemco Spring. Wheel End Spring on a TM 1665 Brake Tie Rod. Ref No. 10 1 per Brake Recommended Spare Part (2LBS)
E016210 Ametek Gemco Switch Kit to complete a Brake Engagement Circuit on a TM1665 Brake. Includes Switch, Bracket, Hardware & Instructions. Some brake modification is required This single switch can be wired for a normally open or a normally closed circuit allowing this switch to show a engaged or disengaged brake. One or the other not both
E016224 Ametek Gemco Block. Inner Tie Rod Block on a ETH14NA Brake
E016232 Ametek Gemco Pin. Pin for the Inner Tie Rod Block on a ETH14NA Brake. Includes Grease Fittings & Retaining Rings (<1LB)
E016500 Ametek Gemco Brake Wheel 16 Inch Diameter. Pilot Bore, TM & ET Brakes
E018500 Ametek Gemco Brake Wheel 16 Inch Diameter, Pilot Bore, TM & ET Brakes
E019022 Ametek Gemco Resistor. External resistor forced for a TM-1985 Brake Assembly
E019024 Ametek Gemco Brake Shoe & Lining Complete for a TM-1985 or ET-19, 19 Inch Diameter Electric Brake Assembly, Qty. 1, 2 per Brake, Ref. # 14, Bonded, Non-Asbestos Material 439C394G01 (45LBS) 1/8
E019025 Ametek Gemco Coil. Shunt Coil for a TM-1985, 19 Inch Brake Assembly. 2 Coils are used on this brake. 32 Volts per coil continuous duty, 40 Volts per coil intermittent duty, average resistance 8.5 Ohms. Coils are connected in series. Ref # 26. Price shown is for a single 1 coil 1/8
E019027 Ametek Gemco Brake Shoe Bolt on a TM1985 or ET19 Brake Assembly. Page Ref. # 16. 2 per brake. 24D6387G01 1.25'' Dia. X 10.5'' L Rod threaded both ends 1 end has pin hole, Nut for use with pin, 1 pin. Nut is on & pinned (5 LBS) 8/7 2 Weeks
E019028 Ametek Gemco Bushing on the Shoe Clapper Arm for a TM1985 orTM2311 Brake, 2 per brake 31D4114H20 3/7 (<1LB)
E019029 Ametek Gemco Bushing on the Brake Base for the TM1985 and TM2311 Brakes, 8 per Brake / 4 Pair 31D4118H19 (1LB) 6/6
E019030 Ametek Gemco Pin. Stop Pin on a TM1985 Brake, 318B571H06 6/6
E019031 Ametek Gemco Clapper Assembly on a TM-1985 Brake. Ref. #25. 1 per brake 318B670G01 1/7
E019032 Ametek Gemco Wheel End Spring Seat on a 19 Inch Frame 1985 Brake, 1 per Brake, 318B777H06 6/6
E019033 Ametek Gemco Spring Clip on a TM-1985 Brake Assembly. Ref. #27. 2 per brake. Old Westinghouse #318B778H06
E019036 Ametek Gemco Pin. Pivot Pin on a TM1985 Brake, 4 per Brake, 318B789H06 3/7
E019037 Ametek Gemco Pin. Tension Spring Pin on a TM-1985 Brake Assembly. Ref # 29 1 per brake. 318B790H06 1/6
E019038 Ametek Gemco Block. Inner Hinge Block on a TM-1985 Brake Tie Rod. Ref # 4 1 per Brake 318B791H06 8/6
E019039 Ametek Gemco Release Bushing, 19 and 23 Inch Brakes, 1 per Brake, 318B792H06 6/6 2 to 3 Weeks
E019040 Ametek Gemco Adjusting Screw for a TM1985 & TM2311 Brake Assembly. Page Ref. # 8. 1 Per Brake. 318B793H06 8/1
E019042 Ametek Gemco Main Spring Seat on a TM1985 Brake Assembly, 1 per Brake, 310B795H06 6/6
E019043 Ametek Gemco Dust Seal for the Coil on a TM1985 Brake, 1 per Brake, 318B917H06 6/6
E019044 Ametek Gemco Main Spring on a TM1985 Brake Assembly, 1 per brake, 438A072H05 8/6
E019045 Ametek Gemco Indicator Bracket on TM-1355 to TM-1985 Brakes. Mounts to coils, facilitates brake adjustment (<1LB)
E019048 Ametek Gemco Adjusting Screw Block. Inner, on a TM1985 Electric Brake Assembly, 1 per Brake, 438A219H01 6/6
E019057 Ametek Gemco Tie Rod on a TM1985 19 Inch Brake Assembly. Ref # 6. 1 per brake. 635C104G06 6/6 2 to 3 Weeks
E019058 Ametek Gemco Outer Brake Shoe Arm with Bushings on a TM1985 Brake. Ref. # 17. 1 per brake. Old Westinghouse # 439C395G01
E019059 Ametek Gemco Clapper & Arm for a TM 1985 Brake, 1 Per brake, 439C397G01
E019060 Ametek Gemco Clapper Arm. Outer Clapper Arm on a TM-1985 Brake Assembly. Includes Bushings. Ref. #24. 1 per Brake 439C398G03 1/7
E019061 Ametek Gemco Coil. Series Wound Coil for a TM1985 Brake, 2 Coils per brake sold individually / each, 637C729G16 (100LBS) 1/8
E019062 Ametek Gemco Coil. Series Coil for a TM1985 Brake, 2 per brake, sold each, 637C523G16, 810 /612 Mill Motors, 0.124 Ohms Resistance Average, 180 Amps 1/2 Hour, 137 Amps 1 Hour (150LBS) 1/8
E019065 Ametek Gemco Lining Kit, pair of drilled linings & rivet fasteners for a TM1985, 19 Inch Diameter Brake 861C691G20, 10-14 Rivet, also available undrilled for bonded brake shoes (8LBS) 6/6
E019066 Ametek Gemco Base on a TM-1985 Brake Assembly. Ref. #18. 1 per brake. Old Westinghouse #439C399G01
E019067 Ametek Gemco Inner Brake Shoe Arm with Bushings on a TM-1985 Brake. Ref. #21. 1 per brake. Old Westinghouse # 439C395G02
E019070 Ametek Gemco Hinge Block on the magnet end of a TM1985 Brake Assembly, 318B788H06 6/6
E019071 Ametek Gemco Wheel End Hinge Block on a TM-1985 Brake Assembly. Ref. # 12. 1 per brake. Old Westinghouse # 318B787H06
E019088 Ametek Gemco Coil. Series Wound Coil for a TM-1955 Brake. 2 Coils per brake sold individually / each. 637C729G17 .002 OHMS / coil. 616 or 814 1/8
E019119 Ametek Gemco Lead. Coil Lead TM-1985 to TM-3014 Brake Coils. Shunt wound coils. 2 per brake (1LB)
E019125 Ametek Gemco Switch Kit to complete a Brake Engagement Circuit on a TM1955 Brake. Includes Switch, Bracket, Hardware & Instructions. Some brake modification is required This single switch can be wired for a normally open or a normally closed circuit allowing this switch to show a engaged or disengaged brake. One or the other not both
E019172 Ametek Gemco Tie Rod for an ET19 Brake, 1 per brake (15LBS)
E019190 Ametek Gemco Tie Rod Assembly Complete with all attached components for a TM-1985 Brake Assembly
E019500 Ametek Gemco Brake Wheel 19 Inch Diameter Pilot Bore TM & ET Brakes
E019503002-G- Ametek Gemco Brake Wheel
E019527002 Ametek Gemco Brake Wheel
E019527002-G- Ametek Gemco Brake Wheel
E019530002-G- Ametek Gemco Brake Wheel
E023022 Ametek Gemco Series Resistor
E023023 Ametek Gemco Resistor. External resistor forced for a TM-2311 Brake Assembly. With taps set as specified on Ametek data sheet, Old Westinghouse # 423A299G06 (5LBS)
E023025 Ametek Gemco Brake Shoe & Lining Complete for a TM-2311, 23 Inch Diameter Electric Brake Assembly, Qty. 1, 2 per Brake, Ref. # 14, Bonded, Non-Asbestos Material 635C316G01 1/8
E023026 Ametek Gemco Coil for a TM-2311 Brake Assembly. Shunt Wound. 2 Coils are required for this brake. 32 Volts per coil continuous duty, 40 Volts per coil intermittent duty, average resistance 6.1 Ohms. Cost per coil, brake requires 2 coils connected in series. Ref # 26. Old # 637C373G16 3/7
E023027 Ametek Gemco Spring. Wheel End Spring on a TM 19, 23 or 30 Inch Brake Tie Rod. Ref No. 10 1 per Brake Recommended Spare Part 24D5096H11 (3LBS) 2/7
E023028 Ametek Gemco Bolt. Brake Shoe Bolt on a TM2311 Brake Assembly. 2 per Brake, 24D6387G02 2/7
E023029 Ametek Gemco Stop Pin on a TM2311 Brake, 1 Per Brake, 318B571H07 2/7
E023030 Ametek Gemco Seat. Wheel End Spring Seat on a TM2311 Brake Assembly, 1 per brake, 318B777H07 8/6
E023031 Ametek Gemco Spring Clip on a TM-2311 Brake Assembly. Ref. #27. 2 per brake. Old Westinghouse #318B778H07
E023034 Ametek Gemco Pin. Pivot Pin for a TM2311 Electric Brake, 4 per Brake, 318B789H07
E023035 Ametek Gemco Pin. Tension Spring Pin on a TM2311 Brake Assembly, 1 per Brake, 318B790H07
E023036 Ametek Gemco Block. Inner Hinge Block on a TM-2311 Brake Tie Rod. Ref. #4. 1 per Brake, 318B791H07 8/6
E023038 Ametek Gemco Main Spring Seat on a TM-2311 Brake. 1 per brake 318B795H07 9/6
E023039 Ametek Gemco Dust Seal for Coil on a TM2311 Electric Brake, 1 Per Brake,318B917H07
E023040 Ametek Gemco Clapper on a TM-2311 Brake Assembly. Ref. #25. 1 per brake. Old Westinghouse #319B098G01
E023044 Ametek Gemco Spring. Tension Spring for a 19 or 23 Inch TM Brake, 438A069H05, Item # 28, 2 per brake, sold each, recommended spare part
E023045 Ametek Gemco Spring. Main Spring on a TM2311 Brake Assembly. Item 3. 438A072H03, 1 per brake. Recommended spare part 8/6
E023046 Ametek Gemco Adjusting Screw Block for a TM2311 Brake Assembly, 1 per Brake, 438A429H01
E023047 Ametek Gemco Tie Rod on a TM2311 23 Inch Brake Assembly, Ref. #6, 1 per Brake, 635C104G07.
E023051 Ametek Gemco Clapper Arm on a TM-2311 Brake Assembly. Ref. #24. 1 per brake. 637C362G01
E023052 Ametek Gemco Clapper & Arm on a TM-2311 Brake Assembly. Ref. #22. 1per brake. 637C343G01
E023053 Ametek Gemco Series Wound Coil for a TM2311 Brake. Qty 1, 2 per brake. 637C502G17
E023054 Ametek Gemco Series Wound Coil for a TM2311 Brake. Qty 1, 2 per brake. 637C502G16
E023055 Ametek Gemco Lining Kit, pair of drilled linings & fasteners for a TM2311, 23 Inch Diameter Brake 861C691G21 11/6
E023056 Ametek Gemco Outer Brake Shoe Arm on a TM-2311 Brake Assembly. Ref. #17. 1 per brake. 637C324G01
E023057 Ametek Gemco Base on a TM-2311 Brake Assembly. Ref. #18. 1 per brake. 434C392G01
E023058 Ametek Gemco Inner Brake Shoe Arm on a TM-2311 Brake Assembly. Ref. #21. 1 per brake. 637C324G02
E023062 Ametek Gemco Hinge Block on the magnet end of a TM2311 Brake, 1 per brake, 318B788H07
E023063 Ametek Gemco Block. Wheel End Hinge Block on a TM-2311 Brake. Ref. # 12 1 per brake, 318B787H07 8/6
E023080 Ametek Gemco Coil. Series Coil for a TM-2311. 246.0 AMPS @ .5 Hr / 183.0 AMPS @ 1.0 Hr Resistance OHMS per Coil = .0100 637C520G20 3/7
E023095 Ametek Gemco Coil. Series Coil for a TM-2311. 105.0 AMPS @ .5 Hr / 80.0 AMPS @ 1.0 Hr Resistance OHMS per Coil = .0550 186C862G16 3/7
E023124 Ametek Gemco Switch Kit to complete a Brake Engagement Circuit on a TM2311 Brake. Includes Switch, Bracket, Hardware & Instructions. Some brake modification is required This single switch can be wired for a normally open or a normally closed circuit allowing this switch to show a engaged or disengaged brake. One or the other not both
E023204 Ametek Gemco Rectifier Assembly for a TM-2311 or TM-3014 and can be used for Qty. 2, TM-43 to TM1985 Brake Assemblies. Supplied with a NEMA 4 Rated Enclosure. An open chassis design is available at less cost. The following AC input voltages are available 380, 440, 550 600. Please specify one voltage at time of order though the panel can be connected for the other voltages (40LBS)
E023205 Ametek Gemco Rectifier Assembly for a TM-2311 or TM-3014 and can be used for Qty. 2, TM-43 to TM1985 Brakes. Open chassis design without enclosure. A NEMA 4 enclosure is available at additional cost. The following AC input voltages are available 380, 440, 550 600. Please specify one voltage at time of order though the panel can be connected for the other voltages (40LBS)
E023500 Ametek Gemco Brake Wheel 23 Inch Diameter with a Pilot Bore BE231001
E023513 Ametek Gemco Brake Wheel, 23 Inch Diameter with a Finished Bore & Keyway for a 612 or 812 Mill Motor. AISE Standard Offset of 8.25 inches BE231003
E023514 Ametek Gemco Brake Wheel, 23 Inch Diameter with a Finished Bore & Keyway for a 614 or 814 Mill Motor. AISE Standard Offset of 8.25 inches BE231004
E023515 Ametek Gemco Brake Wheel, 23 Inch Diameter with a Finished Bore & Keyway for a 616 or 816 Mill Motor. AISE Standard Offset of 8.25 inches BE231002
E023516 Ametek Gemco Brake Wheel, 23 Inch Diameter with a Finished Bore & Keyway for a 618 or 818 Mill Motor. AISE Standard Offset of 8.75 inches BE231005
E023520 Ametek Gemco Brake Wheel 23 Inch Diameter
E023521 Ametek Gemco Brake Wheel 23 Inch Diameter with a pilot bore
E030023 Ametek Gemco Resistor. External resistor forced for a TM-3014 Brake Assembly
E030024 Ametek Gemco Coil. Shunt Wound Coil for a TM-3014 Brake Assembly. 2 Coils per brake, sold each. 32 Volts per coil continuous duty, 40 Volts per coil intermittent duty, average resistance 4.5 Ohms. Ref # 26
E030025 Ametek Gemco Main Spring on a TM-3014 Brake Assembly. Item #3, a recommended spare part. 1 per Brake 438A072H01 7/6
E030026 Ametek Gemco Seat. Main Spring Seat on a TM-3014 Brake. Item #2. 1 per brake 318B795H08 10/7
E030027 Ametek Gemco Brake Shoe & Lining Complete for a TM-30141, 30 Inch Diameter Electric Brake Assembly, Qty. 1, 2 per Brake, Ref. # 14, Bonded, Non-Asbestos Material 426C041G01 7/6
E030030 Ametek Gemco Series Wound Coil for a TM3014 Brake. Qty 1, 2 per brake. Old Westinghouse # 645C518G16
E030031 Ametek Gemco Block. Inner Hinge Block on a TM-3014 Brake Tie Rod. Ref. #4. 1 per Brake 318B795H08 7/6
E030032 Ametek Gemco Release Bushing on a TM-3014 Brake Assembly. Item # 5, 1 per brake 318B792H08 1/7
E030033 Ametek Gemco Tie Rod on a TM-3014 Brake Assembly. Item # 6. 1 per brake. 635C104G08 7/6
E030034 Ametek Gemco Adjusting Screw Block on a TM-3014 Brake. Ref # 7 1 per brake 7/6
E030035 Ametek Gemco Screw. Adjusting Screw on a TM3014 Brake. , Item #3. 1 per Brake, 318B793H08 1/7
E030036 Ametek Gemco Wheel End Spring Seat on a TM-3014 Brake Assembly. Item # 11. 1 per brake 318B777H08 10/7
E030040 Ametek Gemco Brake Shoe Bolt on a TM-3014 Brake Assembly. Ref. # 16. 2 per brake. 450A869G01 3/6
E030043 Ametek Gemco Pin. Pivot Pin 1/7
E030045 Ametek Gemco Bushing on a TM3014 Brake 16 per brake 1/7
E030046 Ametek Gemco Clapper & Arm on a TM-3014 Brake Assembly. Ref. #22. 1 per brake. 641C792G01 3/6
E030047 Ametek Gemco Pin 1/7
E030050 Ametek Gemco Dust Seal for the coil on a TM-3014 Brake Assembly. Recommended spare part. 1 per brake 318B917H08
E030051 Ametek Gemco Spring Clip on a TM-3055 Brake Assembly. Ref # 27 2 per brake. 318B778H08 (1LB) 1/7
E030052 Ametek Gemco Tension Spring for a TM3014 30 Inch Brake. Ref. # 28. 2 per brake. Recommended spare part. 438A411H08 3/6
E030053 Ametek Gemco Pin. Tension Spring Pin on a TM3014 Brake. Ref # 29 1 per brake. 318B790H08 3/6
E030054 Ametek Gemco Brake Lining, TM3014, Old 861C691G22
E030055 Ametek Gemco Coil Leads, TM1355 thru TM3014, include lugs. Series Wound brake coils, 4 per brake ( 2 per coil) the 30 inch brake requires 8 (1LB)
E030079 Ametek Gemco Series Wound Brake Coil for a TM-3014 30 Inch Brake Assembly. 2 per brake, sold individually 645C518G19 2/7
E030096 Ametek Gemco Hinge Block, Magnet End on a TM-3014 Brake Assembly. Item #1. 1 per brake 318B788H08
E030097 Ametek Gemco Hinge Block. Wheel End Hinge Block on a TM-3014 Brake. Item #12. 1 per brake. 318B787H08 7/6
E030101 Ametek Gemco Switch Kit to complete a Brake Engagement Circuit on a TM3014 Brake. Includes Switch, Bracket, Hardware & Instructions. Some brake modification is required This single switch can be wired for a normally open or a normally closed circuit allowing this switch to show a engaged or disengaged brake. One or the other not both
E030500 Ametek Gemco Brake Wheel 30 Inch Diameter Pilot Bore TM Brakes CF
E109062 Ametek Gemco Coil. Series Coil for a TM1985 Brake, 2 per brake, sold each, 637C523G16 1/8
Enclosure CB110 NEMA 4 Ametek Gemco Electric Brake Enclosure. NEMA 4 with Shaft Seals. Shaft Diameters and Approval Drawing required. Must be ordered with brake.
Enclosure CB15 NEMA 4 Ametek Gemco Electric Brake Enclosure. NEMA 4 with Shaft Seals. Shaft Diameters and Approval Drawing required. Must be ordered with brake.
Enclosure CB160 NEMA 4 Ametek Gemco Electric Brake Enclosure. NEMA 4 with Shaft Seals. Shaft Diameters and Approval Drawing required. Must be ordered with brake.
Enclosure CB35 NEMA 4 Ametek Gemco Electric Brake Enclosure. NEMA 4 with Shaft Seals. Shaft Diameters and Approval Drawing required. Must be ordered with brake.
Enclosure CB75 NEMA 3 Ametek Gemco Electric Brake Enclosure. NEMA 3. Approval Drawing required. Must be ordered with brake
Enclosure CB75 NEMA 4 Ametek Gemco Electric Brake Enclosure. NEMA 4 with Shaft Seals. Shaft Diameters and Approval Drawing required. Must be ordered with brake.
Enclosure ET-8 Ametek Gemco Enclosure. NEMA 3R Enclosure for a ET-8 Brake Assembly. Specifically 8210-8-4-A-S-X-X-N-I
Enclosure NEMA 12 Ametek Gemco Enclosure. NEMA 12 Enclosure for all AHM Panels. 36 X 48 Inches
Enclosure TM-1665 NEMA 4 Ametek Gemco Enclosure. NEMA 4 Rated Enclosure for a TM-1665 Brake assembly. Includes Brake Wheel Shaft Seals. Shaft Diameters and approval drawing are required. Enclosures must be ordered with a brake. A Thermostatically Controlled Heater is available at additional cost
Enclosure TM83 Ametek Gemco Enclosure. NEMA 3R Enclosure for a TM83 Brake Assembly
Enclosure TMSC-1035 Ametek Gemco Enclosure. NEMA 3R Enclosure for a TMSC-1035 Brake Assembly
Enclosure TMSC-1355 Ametek Gemco Enclosure. NEMA 3R Enclosure for a TMSC-1355 Brake Assembly. Approval drawing provided, requires signature
Enclosure TMSC-1665 Ametek Gemco Enclosure. NEMA 4 Enclosure for a TMSC-1665 Brake Assembly. Approval drawing provided, requires signature
ET-10 Ametek Gemco Electro-Thrust Brake Assembly, 10 Inch Diameter Brake, 200 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.3 to 7.3 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist applications. 150 LBS + skid. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal 8210104ASXXXI
ET-10DC Ametek Gemco Electro-Thrust Brake Assembly, 10 Inch Diameter Brake, 200 LB FT, 230 VDC., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.3 to 7.3 Sec. to softly apply the brake, 150 LBS + skid
ET-11NA Ametek Gemco Electro-Thrust Brake Assembly. 11 Inch Diameter, 400 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Spring Applied Electrohydraulic Release, Built to AISE specs with the exception of the increased brake torque. -13 thru 104 Degrees F. Brake Setting Times, Without the Adjusting Valve 0.75 Sec. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist applications. With the Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching), enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal (200 LBS)
ET-13 Ametek Gemco Electro-Thrust Brake Assembly, 13 Inch Diameter Brake, 550 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. or With Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist applications. 250 LBS + skid. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal
ET-13DC Ametek Gemco Electro-Thrust Brake Assembly, 13 Inch Diameter Brake, 550 LB FT, 230 VDC,Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. or With Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist applications. 250 LBS + skid. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal
ET-14NA Ametek Gemco Electro-Thrust Brake Assembly, 14 Inch Diameter, 800 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake, 320 LBS + skid Ships via motor freight. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal
ET-14NA DC Ametek Gemco Electro-Thrust Brake Assembly, 14 Inch Diameter, 800 LB FT, 230 VDC, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist applications. 320 LBS + skid Ships via motor freight. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal
ET-16 Ametek Gemco Electro-Thrust Brake Assembly, 16 Inch Diameter Brake, 1000 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.45 Sec. or With Adjusting Valve 0.8 to 3.8 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist applications. 400 LBS + skid. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal
ET-18NA Ametek Gemco Electro-Thrust Brake Assembly, 18 Inch Diameter Brake, 1500 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.35 Sec. With Adjusting Valve 0.7 to 3.0 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist applications. 640 LBS + skid Ships via motor freight. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures & strip heaters
ET-19 Ametek Gemco Electro-Thrust Brake Assembly, 19 Inch Diameter Brake, 2000 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.35 Sec. or With Adjusting Valve 0.7 to 3.0 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist applications. 6400 LBS + skid. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal
ET-19NA Ametek Gemco Electro-Thrust Brake Assembly, 18 Inch Diameter Brake, 1600 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.35 Sec. With Adjusting Valve 0.7 to 3.0 Sec. to softly apply the brake, 640 LBS + skid Ships via motor freight. Options include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters.
ET-23 Ametek Gemco Electro-Thrust Brake Assembly, 8210-23-4-A-S-X-X-X-I
23 Inch Diameter Brake, 4000 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.27 Sec. With Adjusting Valve 0.4 to 1.7 Sec. to softly apply the brake, 875 LBS + skid. Options include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters (900LBS)
ET-30 Ametek Gemco Electro-Thrust Brake Assembly, 30 Inch Diameter Brake, 9000 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve TBD Sec. With Adjusting Valve TBD Sec. to softly apply the brake, 1500 LBS + skid
ET-6NA Ametek Gemco Electro-Thrust Brake Assembly, 6 Inch Diameter Brake, 60 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F., Brake Setting Times Without Adjustable Valve 1.1 Sec. / With Adjustable Valve 1.5 to 7.2 Sec., to softly apply the brake, (as such this brake is not suitable for hoist applications ) 120 LBS + skid., Ships via motor freight. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures & strip heaters
ET-8 Ametek Gemco Electro-Thrust Brake Assembly, 8 Inch Diameter Brake, 100 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F., Brake Setting Times Without Adjustable Valve 1.1 Sec. / With Adjustable Valve 1.5 to 7.2 Sec., to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. 140 LBS + skid. Ships via motor freight. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal.
ET-8DC Ametek Gemco Electro-Thrust Brake Assembly, 8 Inch Diameter Brake, 100 LB FT, 230 VDC, Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F., Brake Setting Times Without Adjustable Valve 1.1 Sec. / With Adjustable Valve 1.5 to 7.2 Sec., to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. 140 LBS + skid. Ships via motor freight. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal
ET-8NA Ametek Gemco Electro-Thrust Brake Assembly, 8 Inch Diameter Brake, 160 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 1.1 Sec. With Adjusting Valve 1.5 to 7.2 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. 140 LBS + skid. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal.
ETH-08NA-DC Brake Only Ametek Gemco Electro-Thrust Brake Assembly, 8 Inch Diameter Brake with hydraulic slave actuator for auxiliary manual cab control via a existing Wagner hydraulic brake system., 160 LB FT, 230 Volt DC Motor, Built to AISE Specifications with the exception of the brake torque which is 60 FT LB higher than AISE specifies, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times; Without Adjusting Valve 1.1 Sec. With Adjusting Valve 1.5 to 7.2 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application (165LBS) Options available at additional cost include: Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures and strip heaters
ETH-10 Brake Only Ametek Gemco spring applied, electro-hydraulically released, 10 inch brake assembly with hydraulic slave actuator for auxiliary manual cab control via the existing Wagner hydraulic brake system. The hydraulic thruster is powered by a 460 / 230 Volt AC motor. 200 FT LBS.
ETH-10 Brake Sys DC Ametek Gemco Electro-Thrust Brake System with Hydraulic Cab Control. 10 Inch Diameter Brake, 200 LB FT, 230 VDC Shunt Wound Motor. Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.3 to 7.3 Sec. to softly apply the brake, hydraulic actuator for auxiliary cab control for a progressive hydraulic brake pedal actuation. System includes: Qty. 1, ET-10 Brake Assembly, Fluid Reservoir Bleeder, Pushbutton Switch with Enclosure for operating the bleeder check valve, Control Cylinder with Foot Pedal, 100 Feet of Hydraulic Tubing, Tube Fittings, Unions, Clamps, Bushings, Brackets, Gaskets, 4 Armored Flexible Hoses & Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703
ETH-10-DC Brake Only Ametek Gemco Electro-Thrust Brake Assembly, 10 Inch Diameter Brake with hydraulic slave actuator for auxiliary manual cab control via a existing Wagner hydraulic brake system., 200 LB FT, 230 Volt DC Motor, Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times; Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.3 to 7.3 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. Options available at additional cost include: Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures and strip heaters # 82300014 (165LBS)
ETH-13 Brake Only Ametek Gemco Electro-Thrust Brake Assembly, 13 Inch Diameter Brake with hydraulic slave actuator for auxiliary manual cab control via a existing Wagner hydraulic brake system., 550 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake, Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. 250 LBS + skid. Options available at additional cost include: Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures and strip heaters.
ETH-13 Brake Only DC Ametek Gemco spring applied, electro-hydraulically released, 13 inch brake assembly with hydraulic slave actuator for auxiliary manual cab control via the existing Wagner hydraulic brake system. The hydraulic thruster is powered by a 230 Volt DC Shunt Wound Motor.550 FT LBS.
ETH-13 Brake Sys Ametek Gemco Electro-Thrust Brake Assembly, 13 Inch Diameter Brake with hydraulic slave actuator for auxiliary manual cab control via a existing Wagner hydraulic brake system., 550 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake, Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. 250 LBS + skid. Options available at additional cost include: Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures and strip heaters. System includes: Qty. 1, ET-13H Brake Assembly, Fluid Reservoir Bleeder, Pushbutton Switch with Enclosure for operating the bleeder check valve, Control Cylinder with Foot Pedal, 100 Feet of Hydraulic Tubing, Tube Fittings, Unions, Clamps, Bushings, Brackets, Gaskets, 4 Armored Flexible Hoses & Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703
ETH-13 Brake Sys DC Ametek Gemco Electro-Thrust Brake System with Hydraulic Cab Control. 13 Inch Diameter Brake, 550 LB FT, 230 VDC Shunt Wound Motor. Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake, hydraulic actuator for auxiliary cab control for a progressive hydraulic brake pedal actuation. System includes: Qty. 1, ET-13 Brake Assembly, Fluid Reservoir Bleeder, Pushbutton Switch with Enclosure for operating the bleeder check valve, Control Cylinder with Foot Pedal, 100 Feet of Hydraulic Tubing, Tube Fittings, Unions, Clamps, Bushings, Brackets, Gaskets, 4 Armored Flexible Hoses & Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703
ETH-14NA Ametek Gemco spring applied, electro-hydraulically released brake assembly with hydraulic actuator for auxiliary manual cab control via foot pedal (sold separately). The thruster includes a 230VDC motor. The brake is set up for a 14'' diameter wheel which is not included. Two 10797 armored hose kits are included. A fluid reservoir bleeder is required, but not included. A manual hydraulic foot pedal control cylinder is required, but not included.
ETH-14NA BO Ametek Gemco spring applied, electro-hydraulically released, 14 inch brake assembly with hydraulic slave actuator for auxiliary manual cab control via the existing Wagner hydraulic brake system. The hydraulic thruster is powered by a 460 / 230 Volt AC motor. 800 FT LBS.
ETH-14NA-DC Brake Only Ametek Gemco Electro-Thrust Brake Assembly, 14 Inch Diameter Brake with hydraulic slave actuator for auxiliary manual cab control via a existing Wagner hydraulic brake system., 800 LB FT, 230 Volt DC Motor, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times; Without Adjusting Valve 0.45 Sec. With Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. Options available at additional cost include: Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures and strip heaters # (300LBS)
ETH-16 Brake Only Ametek Gemco Electro-Thrust Brake Assembly, 16 Inch Diameter Brake with hydraulic slave actuator for auxiliary manual cab control via a existing Wagner hydraulic brake system., 1000 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.45 Sec. With Adjusting Valve 0.8 to 3.8 Sec. to softly apply the brake, Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. 400 LBS + skid. Options available at additional cost include: Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures and strip heaters
ETH-16 Brake Only DC Ametek Gemco spring applied, electro-hydraulically released brake assembly with hydraulic actuator for auxiliary manual cab control via foot pedal (sold separately). 1000 LB / FT. Brake Setting Times, Without Adjusting Valve 0.45 Sec. With Adjusting Valve 0.8 to 3.8 Sec. to softly apply the brake.The thruster includes a 230VDC motor. The brake is set up for a 16'' diameter wheel which is not included. A fluid reservoir bleeder is required, but not included. A manual hydraulic foot pedal control cylinder is required, but not included.
ETH-16 Brake Sys DC Ametek Gemco spring applied, electro-hydraulically released brake system with hydraulic actuator for auxiliary manual cab control via foot pedal. 1000 LB / FT. Brake Setting Times, Without Adjusting Valve 0.45 Sec. With Adjusting Valve 0.8 to 3.8 Sec. to softly apply the brake. The thruster includes a 230VDC Shunt Wound Motor. The brake is set up for a 16'' diameter wheel which is not included. System includes: Qty. 1, ETH-16 Brake Assembly, Fluid Reservoir Bleeder, Pushbutton Switch with Enclosure for operating the bleeder check valve, Control Cylinder with Foot Pedal, 100 Feet of Hydraulic Tubing, Tube Fittings, Unions, Clamps, Bushings, Brackets, Gaskets, 4 Armored Flexible Hoses & Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703
ETH-16 Brake System AC Ametek Gemco Electro-Thrust Brake Assembly, 16 Inch Diameter Brake with hydraulic slave actuator for auxiliary manual cab control via a foot pedal. 1000 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.45 Sec. With Adjusting Valve 0.8 to 3.8 Sec. to softly apply the brake, Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. System includes: Qty. 1, ETH-16 Brake Assembly, Fluid Reservoir Bleeder, Pushbutton Switch with Enclosure for operating the bleeder check valve, Control Cylinder with Foot Pedal, 100 Feet of Hydraulic Tubing, Tube Fittings, Unions, Clamps, Bushings, Brackets, Gaskets, 4 Armored Flexible Hoses & Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703400 LBS + skid. Options available at additional cost include: Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures and strip heaters
F00017 Ametek Gemco Gasket. Copper Gasket , used with armored hose, 33/64'' I.D. (<1LB)
F000602 Ametek Gemco Gasket. Copper Gasket (<1LB)
F000603 Ametek Gemco Gasket. Copper Gasket (<1LB)
F000996 Ametek Gemco Plug
F002395 Ametek Gemco Boot. Actuator Boot, Item 11, used on actuating cylinders J007905, J023437 & J008765 (1LB)
F004481 Ametek Gemco Adapter 1 X 16 for a Disc Brake Power Cluster (-1LB)
F006446 Ametek Gemco Screw. Bleeder Screw (<1LB)
F011955 Ametek Gemco Adaptor Fitting, 1/2 -20 UNF Male to 1/4-18 NPTF Male, Brass (1LB)
F020412 Ametek Gemco 2 Way Hydraulic Check Valve with Fittings for 1/4 Inch O.D. Copper Tubing
F034635 Ametek Gemco Displacement Cylinder
FRBKIT Ametek Gemco Fluid Reservoir Bleeder Kit including an AC or DC fluid reservoir bleeder assembly, a bleeder pushbutton and necessary tubing, fittings and brake fluid.
Hand Release Ametek Gemco Hand Release Option. Must be ordered with brake
HM18X8-1 Ametek Gemco Hydraulic Brake System. Cab controlled Type HM Brake system with Parking Brake. Qty. 18 X 8 Brake, with Type HM Control Unit and Parking Brake Control Station, Fluid Reservoir Bleeder, Bleeder Push-Button, Control Cylinder & Pedal, Armored Hoses, 150 Feet of Tubing, Fittings & Brake Fluid. Specify whether bleeder check valve is to be controlled by 230 VDC / 115 Volt AC or Manually Operated via a 90 Degree Ball Valve
J000086 Ametek Gemco Nut. Brass Tube Nut for the connection of flared copper tubing joints (1LB)
J000233 Ametek Gemco Fastener. Brass Brake Lining Fastener Assembly for use with Lining J004954. Item # 25. 7/16 Inch Diameter Brass Slotted Screw / Bolt, Nut & Lockwasher for a 10 Inch Brake J002926, 8 per lining, 16 per brake, sold each (<1LB)
J000269 Ametek Gemco Outlet Fitting. 1/2 X 20 male thread at both ends. 1 end is for flared tubing the other end is flat like the end of the armored hose requires F17 copper gasket (<1LB)
J000363 Ametek Gemco Fastener. Brass Brake Lining Fastener Assembly for use with Lining J001276 & J001234. Item # 24. 5/8 Inch Diameter Brass Slotted Screw / Bolt, Nut & Lockwasher for a 14 & 18 Inch Brake, 6 per lining, 12 per brake, sold each (<1LB)
J000387 Ametek Gemco Fastener. Brass Brake Lining Fastener Assembly for use with Lining J23024 & J007846. Item # 4. Brass Slotted Screw / Bolt, Nut & Lockwasher for 6 & 8 Inch Brakes, 6 per lining, 12 per brake, sold each (<1LB)
J000391 Ametek Gemco Spring Clamp Tool for air releasing cylinders.
J001234 Ametek Gemco Lining. Brake Lining for a 14 Inch Hydraulic Brake. Lining has 8 Drilled & Countersunk holes for J000363 Brass Fasteners sold separately. Ref item # 23. 2 per brake. Sold each. 287DC Scan-Pak, Non Asbestos, MSDS Sheet Provided ( 7 LBS)
J001235 Ametek Gemco Brake Shoe & Lining for a 14 Inch Hydraulic Brake. Bonded linings with new pin & hardware. Qty. 1, 2 per brake assembly (23LBS)
J001276 Ametek Gemco Lining. Brake Lining for an 18 Inch Hydraulic Brake. Lining has 14 Drilled & Countersunk holes for J00363 Brass Fasteners sold separately. Ref item # 23. 2 per brake. Sold each. 288DC Scan-Pak, Non Asbestos, MSDS Sheet Provided ( 8 LBS)
J001396 Ametek Gemco Head Gasket, Head & Barrel to Control Cylinder Seal
J001768 Ametek Gemco Arm. Lever Arm on a 14 Inch Hyd brake. Ref item # 12. 1 per brake
J001803 Ametek Gemco Brake Shoe & Lining for a 18 Inch Hydraulic Brake, Qty. 1, 2 per brake (35LBS) ISG CLE 1231853
J002395 Ametek Gemco Boot. Actuator Boot, Item 11, used on actuating cylinders J007905, J023437 & J008765 (1LB)
J002398 Ametek Gemco Brake Base for 6 or 8 Inch Hydraulic Brake ISG SAP 1094553
J002680 Ametek Gemco Brake Base, 10 Inch Hydraulic ISG SAP 1094527
J002681 Ametek Gemco Shoe Arm, 10 Inch Hydraulic ISG SAP 1087483
J002682 Ametek Gemco Shoe Arm, 10 Inch Hydraulic ISG SAP 1087484
J002683 Ametek Gemco Base for a 2929 14 Inch Brake ISG SAP 1094535
J002684 Ametek Gemco Shoe Arm on a 14 Inch Brake, right side with provision for shoe centering lock kit ISG SAP 1087485
J002685 Ametek Gemco Shoe Arm on a 14 Inch Brake with mount for hyd. cylinder ISG SAP 1087486
J002686 Ametek Gemco 18 Inch Hyd Centering Spring
J002779 Ametek Gemco Brake Assembly. 8 X 3 Inch Hydraulic Brake Assembly, 200 to 450 FT LBS (30LB)
J002926 Ametek Gemco Brake Assembly. Hydraulic Brake, 10 Inch Diameter, Type H. Hydraulic Actuator and the Brake Wheel are not included (93LBS)
J002929 Ametek Gemco Hydraulic Brake Assembly. 14 Inch Diameter Type ''H'' Hydraulic Brake, ships less the Hydraulic Actuator which must be purchased separately. 0 to 600 FT LBS on a Manual Brake System. 0 to 1400 FT LBS on a Air over Hydraulic Powered Brake System. A 14 X 6 Inch Brake Wheel is not included (161LBS)
J002932 Ametek Gemco Brake Assembly, 18 X 8 Type H. Up to 900 LBS. / FT. dynamic stopping torque on a manual hydraulic brake system. 1800 LBS. / FT. dynamic stopping torque on a Air / Hydraulic brake system. 27.75 Inches Wide. 34.375 Inches high with brake applied. A hydraulic actuator and brake wheel are not included (266LBS)
J002935 Ametek Gemco Base. Brake Base on an 18 Inch Hydraulic Brake. Item 26, 1 per brake (40LBS)
J002936 Ametek Gemco Arm. Brake Shoe Arm on an 18 Inch Hydraulic Brake. Item 18, 1 per brake (20LBS)
J002937 Ametek Gemco Arm. Brake Shoe Arm on an 18 Inch Hydraulic Brake. Item 1, 1 per brake. Arm that has the actuator (20LBS)
J003054 Ametek Gemco Actuator. Type HM Hydraulic Actuator / Slave Cylinder on a 6 or 8 Inch Hyd Brake with the Parking Brake Option. Item 29A, 1 per brake (11LBS) ISG SAP 1085518
J003080 Ametek Gemco Brake Fluid Reservoir Bleeder. OBSOLETE, replaced by PSD-0180101. Includes a Solenoid Operated Valve which is controlled by a remotely mounted switch which is not included. 230 Volt DC, Fluid Capacity 2-1/3 rd Quart. Replaced by PSD0180101 (13LBS)
J003082 Ametek Gemco Brake Fluid Reservoir Bleeder. OBSOLETE, replaced by PSD0180100. Ametek Gemco Brake Fluid Reservoir Bleeder. Includes a Solenoid Operated Valve which is controlled by a remotely mounted switch which is not included. 440 Volt AC, 50/60 Hz., 45VA. Fluid Capacity 2-1/3 rd Quart. Net Weight 9 LBS Replaced by PSD-0180100 110 Volt
J003083 Ametek Gemco Brake Fluid Reservoir Bleeder. OBSOLETE, replaced by PSD0180100. Ametek Gemco Brake Fluid Reservoir Bleeder. Includes a Solenoid Operated Valve which is controlled by a remotely mounted switch which is not included. 110 Volt AC, 50/60 Hz., 45VA. Fluid Capacity 2-1/3 rd Quart. Net Weight 9 LBS Replaced by PSD-0180100. (ISGSAP1267689)
J003205 Ametek Gemco Brake Assembly. 8 X 3 Inch Type HM Brake, 200 FT LBS Manual Operation / 450 FT LBS Air over Hydraulic Operation. HM = Spring Set Parking & Holding 50 FT LBS, includes actuator (32LBS)
J004954 Ametek Gemco Brake Lining, 10 Inch Diameter, Hydraulic, drilled and countersunk for 8 brass fasteners
J005137 Ametek Gemco Bushing. Tube Bushing for brake lines (<1LB)
J005138 Ametek Gemco Clamp. Bushing Clamp for brake lines (<1LB)
J005780 Ametek Gemco Hose Bracket for the armored hose
J006110 Ametek Gemco Brake Shoe & Lining for a 10 Inch Hydraulic Brake J002926. Bonded linings with new pin & hardware Qty. 1, 2 per brake assembly (13LBS)
J006693 Ametek Gemco Bushing. Knuckle Bushing on a 14 or 18 Inch Brake (1LB) ISG SAP 1111645
J006694 Ametek Gemco Eye Bolt Bushing used on a 10, 14 or 18 Inch Hyd. Brake ISG SAP 1111273
J006696 Ametek Gemco Pin on a 14 or 18 Inch Brake Assembly. Connects top of the hydraulic actuator to the lever arm.1/2 Inch Diameter X 2.375'' Long. Smallest solid pin with two holes for cotter pins. 1 per brake CMH000180 (<1LB)
J006816 Ametek Gemco Pin on a 14 Inch Brake Assembly. Mounts shoes & the bottom of both brake arms. 5.875 Inch Long X 1 Inch Diameter 0.875-14