Spec Tech Industrial

Back___________________Next__________________Home<

Buy Your Industrial Control Products Here!

Gemco Parts Description Page 21

Part
Number
Product
Category
Description
CB-110 Brake Parts Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / solenoid Released, 7 Inch Diameter, AC Voltages, 60 or 50 Hz., Single Phase., 85 Ft LB Continues or 110 FT LB Intermittent, less a 7.00 X 4.25 Inch Brake Wheel. 60 LBS. Gross Reliable design with very few parts. Simple one point torque adjustment. Rugged long life solenoid - tested in more than 2 million operational cycles without electrical failure. Manual brake release with hand pressure on the solenoid arm. Solenoid plunger travel indicator - a mark on the plunger indicates when the brake should be adjusted for lining wear. Simple two-point adjustment for lining wear.
CB-15 Brake Parts Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 4.5 Inch Diameter, AC Voltages, 60 or 50 Hz., Single Phase., 10 Ft LB Continues or 15 FT LB Intermittent, less a 4.50 X 2.75 Inch Brake Wheel E004800. (20LBS) Reliable design with very few parts. Simple one point torque adjustment. Rugged long life solenoid - tested in more than 2 million operational cycles without electrical failure. Manual brake release with hand pressure on the solenoid arm. Solenoid plunger travel indicator - a mark on the plunger indicates when the brake should be adjusted for lining wear. Simple two-point adjustment for lining wear.
CB-160 Brake Parts Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 10 Inch Diameter, Many AC Voltages, 60 or 50 Hz., Single Phase., 160 FT LB Intermittent Duty, 125 FT LB continues Duty, less a 10.00 X 4.25 Inch Brake Wheel E010800. 78 LBS Net. Motor Freight on a skid. Reliable design with very few parts. Simple one point torque adjustment. Rugged long life solenoid - tested in more than 2 million operational cycles without electrical failure. Manual brake release with hand pressure on the solenoid arm. Solenoid plunger travel indicator - a mark on the plunger indicates when the brake should be adjusted for lining wear. Simple two-point adjustment for lining wear
CB-35 Brake Parts Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 5.50 Inch Diameter, AC Voltages, 60 or 50 Hz., Single Phase., 25 Ft LB Continues or 35 FT LB Intermittent, less a 5.50 X 3.25 Inch Brake Wheel E005500. (34LBS) Reliable design with very few parts. Simple one point torque adjustment. Rugged long life solenoid - tested in more than 2 million operational cycles without electrical failure. Manual brake release with hand pressure on the solenoid arm. Solenoid plunger travel indicator - a mark on the plunger indicates when the brake should be adjusted for lining wear. Simple two-point adjustment for lining wear
CB-75 Brake Parts Ametek Gemco Brake Assembly, AC Solenoid, Spring Set / Solenoid Released, 7 Inch Diameter, AC Voltages, 60 & 50 Hz., Single Phase, 50 FT LB Continues or 75 FT LB Intermittent, less a 7.00 X 4.25 Inch Brake Wheel E007500. (60LBS) Reliable design with very few parts. Simple one point torque adjustment. Rugged long life solenoid - tested in more than 2 million operational cycles without electrical failure. Manual brake release with hand pressure on the solenoid arm. Solenoid plunger travel indicator - a mark on the plunger indicates when the brake should be adjusted for lining wear. Simple two-point adjustment for lining wear
CO197500 Brake Parts Ametek Gemco Cover. Cover only for a Series 1980 NEMA , 4 to 6 Circuit Cam Box (4LBS)
Cast Iron or Bronze Encl Brake Parts Ametek Gemco Cast Bronze Enclosure for NEMA 4 2000 Series Worm Gear Limit Switches, adder
Coil TM- 63 Brake Parts Ametek Gemco Coil for a TM-63 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 1 per brake.
Coil TM- 83 Brake Parts Ametek Gemco Coil for a TM-83 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each (25LBS)
Coil TM-1035 Brake Parts Ametek Gemco Coil for a TM-1035 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each (30LBS)
Coil TM-1355 Brake Parts Ametek Gemco Coil for a TM-1355 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each
Coil TM-1665 Brake Parts Ametek Gemco Coil for a TM-1665 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each
Coil TM-1985 Brake Parts Ametek Gemco Coil for a TM-1985 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each 1/8
Coil TM-2311 Brake Parts Ametek Gemco Coil for a TM-2311 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each 3/7
Coil TM-3014 Brake Parts Ametek Gemco Coil for a TM-3014 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 2 per brake. Sold each
Coil TM-43 Brake Parts Ametek Gemco Coil for a TM-43 Brake. This description is for pricing only. Exact part number is required at time of order. Ref # 26 1 per brake.
Conversion System Type H Brake Parts Ametek Gemco A/H-ERC Conversion System for Type H Wagner Hydraulic Brake Systems. Converts a Wagner manual brake system to an Air Over Hydraulic Brake System that can be controlled remotely via an electric circuit. This conversion is for Wagner Hydraulic Brake Systems though other hydraulic brake systems could be suitable for this conversion. (system suitability investigation would be required) The Conversion System Includes: One 3/4 HP Motor Driven Compressor Assembly, One Pre- Piped and Pre-Wired Control Panel, One Two-Way Hydraulic Check Valve, One Installation Kit including all the necessary tubing, fittings & fluid. If the existing brake system does not include a Fluid Reservoir Bleeder, it is required, and is at additional cost. This system requires electrical input of 230 Volt DC or 460 Volt AC, 3 Phase, 60 Hz for the compressor and 115 Volt Control on AC Systems. Please specify AC or DC at time of order. Systems are available with the HM parking option at additional cost.
D7010 Brake Parts Ametek Gemco Yates Tube. Replacement Tube, H4-F-N3.2X-1.00X1.38XXS13, Rev NS, TM1355
DT-2RV212-A7 Brake Parts Ametek Gemco Switch 04537003
E004022 Brake Parts Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 4.5 Inch Diameter, 460 Volt AC, 60 Hz., Single Phase., 15 FT LB Intermittent, less a 4.50 X 2.75 Inch Brake Wheel E004800. (20LBS)
E004044 Brake Parts Ametek Gemco Resistor for a TM43 Brake Assembly with a shunt wound coil. This is the standard resistor. Not to be used with rectifiers employing a Forcing Scheme. E004045 is used with a Forcing Scheme Rectifier
E004045 Brake Parts Ametek Gemco Resistor. Forcing Resistor for use with a TM-43 Brake Assembly
E004047 Brake Parts Ametek Gemco Brake Shoe & Lining for a TM-43 4.5 Inch Electric Brake, Bonded Non-Asbestos Lining Material. Sold each, 2 per Brake. 70 Degree Arc, 645C555G02 (2LBS)
E004051 Brake Parts Ametek Gemco Coil. Shunt Wound Coil for a TM-43 Brake Assembly. Intermittent Duty, 1 Hour Cycle 80 Volts DC / 1.10 AMPS. Continuous Duty, 8 Hour Cycle 64 Volts DC / 0.88 AMPS. Average Cold Coil Resistance 73 OHMS. Ref # 26 1 coil per brake 645C545G16 Resistors are required in series E004044 / Forcing E004045 (16LBS)
E004054 Brake Parts Ametek Gemco Pin on a CB35 Brake. Ref # 14 3 per brake @ bottom & top of brake shoes 2247C08H01 (<1LB)
E004055 Brake Parts Ametek Gemco Pin on a CB-15 Brake Assembly. Between Link and Lever. Ref. # 8 1 per brake. 2247C08H02 (<1LB)
E004056 Brake Parts Ametek Gemco Pin on a CB15 Brake Assembly. Connects plunger & link. Item Ref. 6. 1 per brake 2247C08H03 (<1LB)
E004059 Brake Parts Ametek Gemco Lever for a CB15 4 & 1/2 Inch Brake Assembly. Lever between plunger link and inner shoe arm. 2247C09H01
E004060 Brake Parts Ametek Gemco Rod. Adjusting Rod on a CB15 4 & 1/2 Inch Brake, 1 per brake. Ref # 17 , 3279B86G01
E004062 Brake Parts Ametek Gemco Link on a CB-15 brake Assembly. Between plunger & lever arm. Item Ref. 7. 1 per brake. 3279B92H01 (1LB)
E004063 Brake Parts Ametek Gemco Spring Seat on a CB15 Brake Assembly. Ref # 10 1 per brake. Old Westinghouse # 3279B94Ho2
E004065 Brake Parts Ametek Gemco Spring, Main Tension on a CB15 Brake Assembly. Ref # 11 1 per brake. Old Westinghouse # 3280B02H01
E004070 Brake Parts Ametek Gemco Bolt. Brake Shoe Bolt for a TM43 or TM63 Brake, 27D7221H04 1/2 - 13 X 3-1/4" LG STL G2 PLATED HEX HD CAP Ref # 15, 2 per brake (1LB)
E004071 Brake Parts Ametek Gemco Seat/ Plate. Spring Seat / Plate on the Wheel End of a TM43 Brake, Ref. # 9, 318B777H01 (1LB)
E004074 Brake Parts Ametek Gemco Block. Inner Hinge Block on a TM-43 Brake Tie Rod. Ref. #4. 1 per Brake 318B791H01
E004075 Brake Parts Ametek Gemco Release Bushing on a TM43 Brake
E004076 Brake Parts Ametek Gemco Main Spring Seat on a TM43 Brake Assembly
E004077 Brake Parts Ametek Gemco Dust Seal for the Coil on a TM43 Brake Assembly
E004078 Brake Parts Ametek Gemco Spring. Wheel End Spring on a TM-43 Brake Tie Rod Ref. # 11 1 per brake. Recommended spare part 438A070H15 (1LB)
E004079 Brake Parts Ametek Gemco Tension Spring on a TM43 Brake Assembly
E004080 Brake Parts Ametek Gemco Tension Spring on a TM43 Brake Assembly
E004097 Brake Parts Ametek Gemco Tie Rod on a TM43 4 Inch Brake Assembly. Ref #7. 1 per brake. Old Westinghouse 635C104G09
E004098 Brake Parts Ametek Gemco Bushing for a TM43 or TM63 Brake Assembly, 2 per brake
E004101 Brake Parts Ametek Gemco Lining and Rivet Kit on a CB15 Brake Assembly. Linings have 4 countersunk holes for the rivets. Also available undrilled for bonded applications. Old Westinghouse # 3279B95G01 1 kit per brake. recommended spare part (1LB)
E004102 Brake Parts Ametek Gemco Coil for a CB-15 Brake. 460 Volt 60 Hz. Single Phase, 3280B04G03 (1LB)
E004104 Brake Parts Ametek Gemco Coil for a CB-15 Brake. 115 Volt 60 Hz. Single Phase, 3280B04G01 (1LB)
E004105 Brake Parts Ametek Gemco Coil for a CB-15 Brake. 230 Volt 60 Hz. Single Phase, 3280B04G02 (1LB)
E004107 Brake Parts Ametek Gemco Coil for a CB-15 Brake. 200 Volt 60 Hz. Single Phase, 3280B04G17 (1LB)
E004109 Brake Parts Ametek Gemco Solenoid Assembly on a 4.5" Dia. CB15 Brake Assembly, includes Plunger & Solenoid Guides, 3279B97H01
E004113 Brake Parts Ametek Gemco Shoe with Lining, Inner, for a CB15 Brake, old 2254C28G01
E004114 Brake Parts Ametek Gemco Shoe with Lining, Outer, for a CB15 Brake, old 2254C27G01
E004117 Brake Parts Ametek Gemco Lining & Rivet Kit for a TM43 4.5 Inch Dia. Electric Brake, 1 Pair drilled for with rivets. The rivets are included. Old Westinghouse # 961C691G23. Undrilled linings for bonded application are also available. Just specify undrilled on any order.
E004118 Brake Parts Ametek Gemco Arm. Outer Brake Shoe Arm on a TM-43 Brake. Ref # 16, 1 per brake, 645C544G01
E004143 Brake Parts Ametek Gemco Block. Wheel End Hinge Block for a TM43 Brake. Ref # 12 1 per brake. 318B787H01
E004153 Brake Parts Ametek Gemco Coil for a TM43 Brake. Series Wound Coil. 32 Amps 1/2 Hour & 26.5 Amps 1 Hour. Resistance 0.181 OHMS.
E004154 Brake Parts Ametek Gemco Coil. Series Coil for a TM-43 Brake Assembly. 26.5 AMPS Intermittent Duty Cycle, 0.287 Ohms Resistance, G645C545G26 (8 LBS)
E004167 Brake Parts Ametek Gemco Coil. Series Coil for a TM-43 Brake Assembly. 12.5 Amps .5 Hour & 10.3 Amps 1 Hour. Resistance 1.18 Ohms, average.. Ref # 26 1 Coil is required on this brake. Old Westinghouse # 645C545G23
E004175 Brake Parts Ametek Gemco Bushing. Neoprene Bushing on a CB-15 or CB-35 Brake. 2 per brake (<1LB)
E004182 Brake Parts Ametek Gemco Series Coil for a TM-43 Brake Assembly. .Item # 26. 936 Ohms Res. 14 AMPS / 1/2 Hour . 11.5 AMPS / 1 Hour. Old Westinghouse # 208C757G16 1 per brake.
E004500 Brake Parts Ametek Gemco Brake Wheel for the TM-43 Brake Assembly, 4.5 Inch Diameter, 3.125" Face, 1.56 Offset, 2.62" Hub Length, 2.75 Inch Hub Diameter, 1.625" Maximum Bore, 9850 Maximum, RPM, Offset Hub Style ( symmetrical hub style also available), Solid Hub with centerline machined. WK2 / LB FT2 .14 Add $ 125.00 to finish hub offset, hub length, bore & key.
E004600999-C- Brake Parts Ametek Gemco Brake Wheel 4.5
E004800 Brake Parts Ametek Gemco Brake Wheel for the CB15 Brake Assembly, 4.5 Inch Diameter, 2.75" Face, 2.64" Offset, 2.2" Hub Length, Solid Hub with center line machined. 1.625" Maximum Bore, 9850 Maximum RPM, 2247C13H01 Add $125.00 to finish hub, bore & keyway (9LBS)
E005001 Brake Parts Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 5.50 Inch Diameter, 230 VAC, 60 Hz., Single Phase., 35 FT LB Intermittent, less a 5.50 X 3.25 Inch Brake Wheel (29LBS)
E005002 Brake Parts Ametek Gemco Magnetic Shoe Brake Assembly, Spring Set / Solenoid Released, 5.50 Inch Diameter, 460 VAC, 60 Hz., Single Phase., 35 FT LB Intermittent, less a 5.50 X 3.25 Inch Brake Wheel (29LBS)
Updated on February 26, 2016 1:30 PM
203 Vest Avenue
Valley Park, MO 63088
Toll Free: (888) SPECTECH
Phone: (636) 537-0202
Fax: (636) 537-1405
E:mail: sales@spectechind.com