Spec Tech Industrial

Back___________________Next__________________Home

Buy Your Industrial Control Products Here!

Gemco Parts Description Page 27


Part
Number
Product
Category
Description
E023063 Brake Parts Ametek Gemco Block. Wheel End Hinge Block on a TM-2311 Brake. Ref. # 12 1 per brake, 318B787H07 8/6
E023080 Brake Parts Ametek Gemco Coil. Series Coil for a TM-2311. 246.0 AMPS @ .5 Hr / 183.0 AMPS @ 1.0 Hr Resistance OHMS per Coil = .0100 637C520G20 3/7
E023095 Brake Parts Ametek Gemco Coil. Series Coil for a TM-2311. 105.0 AMPS @ .5 Hr / 80.0 AMPS @ 1.0 Hr Resistance OHMS per Coil = .0550 186C862G16 3/7
E023124 Brake Parts Ametek Gemco Switch Kit to complete a Brake Engagement Circuit on a TM2311 Brake. Includes Switch, Bracket, Hardware & Instructions. Some brake modification is required This single switch can be wired for a normally open or a normally closed circuit allowing this switch to show a engaged or disengaged brake. One or the other not both
E023204 Brake Parts Ametek Gemco Rectifier Assembly for a TM-2311 or TM-3014 and can be used for Qty. 2, TM-43 to TM1985 Brake Assemblies. Supplied with a NEMA 4 Rated Enclosure. An open chassis design is available at less cost. The following AC input voltages are available 380, 440, 550 600. Please specify one voltage at time of order though the panel can be connected for the other voltages (40LBS)
E023205 Brake Parts Ametek Gemco Rectifier Assembly for a TM-2311 or TM-3014 and can be used for Qty. 2, TM-43 to TM1985 Brakes. Open chassis design without enclosure. A NEMA 4 enclosure is available at additional cost. The following AC input voltages are available 380, 440, 550 600. Please specify one voltage at time of order though the panel can be connected for the other voltages (40LBS)
E023500 Brake Parts Ametek Gemco Brake Wheel 23 Inch Diameter with a Pilot Bore BE231001
E023513 Brake Parts Ametek Gemco Brake Wheel, 23 Inch Diameter with a Finished Bore & Keyway for a 612 or 812 Mill Motor. AISE Standard Offset of 8.25 inches BE231003
E023514 Brake Parts Ametek Gemco Brake Wheel, 23 Inch Diameter with a Finished Bore & Keyway for a 614 or 814 Mill Motor. AISE Standard Offset of 8.25 inches BE231004
E023515 Brake Parts Ametek Gemco Brake Wheel, 23 Inch Diameter with a Finished Bore & Keyway for a 616 or 816 Mill Motor. AISE Standard Offset of 8.25 inches BE231002
E023516 Brake Parts Ametek Gemco Brake Wheel, 23 Inch Diameter with a Finished Bore & Keyway for a 618 or 818 Mill Motor. AISE Standard Offset of 8.75 inches BE231005
E023520 Brake Parts Ametek Gemco Brake Wheel 23 Inch Diameter
E023521 Brake Parts Ametek Gemco Brake Wheel 23 Inch Diameter with a pilot bore
E030023 Brake Parts Ametek Gemco Resistor. External resistor forced for a TM-3014 Brake Assembly
E030024 Brake Parts Ametek Gemco Coil. Shunt Wound Coil for a TM-3014 Brake Assembly. 2 Coils per brake, sold each. 32 Volts per coil continuous duty, 40 Volts per coil intermittent duty, average resistance 4.5 Ohms. Ref # 26
E030025 Brake Parts Ametek Gemco Main Spring on a TM-3014 Brake Assembly. Item #3, a recommended spare part. 1 per Brake 438A072H01 7/6
E030026 Brake Parts Ametek Gemco Seat. Main Spring Seat on a TM-3014 Brake. Item #2. 1 per brake 318B795H08 10/7
E030027 Brake Parts Ametek Gemco Brake Shoe & Lining Complete for a TM-30141, 30 Inch Diameter Electric Brake Assembly, Qty. 1, 2 per Brake, Ref. # 14, Bonded, Non-Asbestos Material 426C041G01 7/6
E030030 Brake Parts Ametek Gemco Series Wound Coil for a TM3014 Brake. Qty 1, 2 per brake. Old Westinghouse # 645C518G16
E030031 Brake Parts Ametek Gemco Block. Inner Hinge Block on a TM-3014 Brake Tie Rod. Ref. #4. 1 per Brake 318B795H08 7/6
E030032 Brake Parts Ametek Gemco Release Bushing on a TM-3014 Brake Assembly. Item # 5, 1 per brake 318B792H08 1/7
E030033 Brake Parts Ametek Gemco Tie Rod on a TM-3014 Brake Assembly. Item # 6. 1 per brake. 635C104G08 7/6
E030034 Brake Parts Ametek Gemco Adjusting Screw Block on a TM-3014 Brake. Ref # 7 1 per brake 7/6
E030035 Brake Parts Ametek Gemco Screw. Adjusting Screw on a TM3014 Brake. , Item #3. 1 per Brake, 318B793H08 1/7
E030036 Brake Parts Ametek Gemco Wheel End Spring Seat on a TM-3014 Brake Assembly. Item # 11. 1 per brake 318B777H08 10/7
E030040 Brake Parts Ametek Gemco Brake Shoe Bolt on a TM-3014 Brake Assembly. Ref. # 16. 2 per brake. 450A869G01 3/6
E030043 Brake Parts Ametek Gemco Pin. Pivot Pin 1/7
E030045 Brake Parts Ametek Gemco Bushing on a TM3014 Brake 16 per brake 1/7
E030046 Brake Parts Ametek Gemco Clapper & Arm on a TM-3014 Brake Assembly. Ref. #22. 1 per brake. 641C792G01 3/6
E030047 Brake Parts Ametek Gemco Pin 1/7
E030050 Brake Parts Ametek Gemco Dust Seal for the coil on a TM-3014 Brake Assembly. Recommended spare part. 1 per brake 318B917H08
E030051 Brake Parts Ametek Gemco Spring Clip on a TM-3055 Brake Assembly. Ref # 27 2 per brake. 318B778H08 (1LB) 1/7
E030052 Brake Parts Ametek Gemco Tension Spring for a TM3014 30 Inch Brake. Ref. # 28. 2 per brake. Recommended spare part. 438A411H08 3/6
E030053 Brake Parts Ametek Gemco Pin. Tension Spring Pin on a TM3014 Brake. Ref # 29 1 per brake. 318B790H08 3/6
E030054 Brake Parts Ametek Gemco Brake Lining, TM3014, Old 861C691G22
E030055 Brake Parts Ametek Gemco Coil Leads, TM1355 thru TM3014, include lugs. Series Wound brake coils, 4 per brake ( 2 per coil) the 30 inch brake requires 8 (1LB)
E030079 Brake Parts Ametek Gemco Series Wound Brake Coil for a TM-3014 30 Inch Brake Assembly. 2 per brake, sold individually 645C518G19 2/7
E030096 Brake Parts Ametek Gemco Hinge Block, Magnet End on a TM-3014 Brake Assembly. Item #1. 1 per brake 318B788H08
E030097 Brake Parts Ametek Gemco Hinge Block. Wheel End Hinge Block on a TM-3014 Brake. Item #12. 1 per brake. 318B787H08 7/6
E030101 Brake Parts Ametek Gemco Switch Kit to complete a Brake Engagement Circuit on a TM3014 Brake. Includes Switch, Bracket, Hardware & Instructions. Some brake modification is required This single switch can be wired for a normally open or a normally closed circuit allowing this switch to show a engaged or disengaged brake. One or the other not both
E030500 Brake Parts Ametek Gemco Brake Wheel 30 Inch Diameter Pilot Bore TM Brakes CF
E109062 Brake Parts Ametek Gemco Coil. Series Coil for a TM1985 Brake, 2 per brake, sold each, 637C523G16 1/8
ET-10 Brake Parts Ametek Gemco Electro-Thrust Brake Assembly, 10 Inch Diameter Brake, 200 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.3 to 7.3 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist applications. 150 LBS + skid. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal 8210104ASXXXI
ET-10DC Brake Parts Ametek Gemco Electro-Thrust Brake Assembly, 10 Inch Diameter Brake, 200 LB FT, 230 VDC., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.3 to 7.3 Sec. to softly apply the brake, 150 LBS + skid
ET-11NA Brake Parts Ametek Gemco Electro-Thrust Brake Assembly. 11 Inch Diameter, 400 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Spring Applied Electrohydraulic Release, Built to AISE specs with the exception of the increased brake torque. -13 thru 104 Degrees F. Brake Setting Times, Without the Adjusting Valve 0.75 Sec. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist applications. With the Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching), enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal (200 LBS)
ET-13 Brake Parts Ametek Gemco Electro-Thrust Brake Assembly, 13 Inch Diameter Brake, 550 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. or With Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist applications. 250 LBS + skid. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal
ET-13DC Brake Parts Ametek Gemco Electro-Thrust Brake Assembly, 13 Inch Diameter Brake, 550 LB FT, 230 VDC,Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. or With Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist applications. 250 LBS + skid. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal
ET-14NA Brake Parts Ametek Gemco Electro-Thrust Brake Assembly, 14 Inch Diameter, 800 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake, 320 LBS + skid Ships via motor freight. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal
ET-14NA DC Brake Parts Ametek Gemco Electro-Thrust Brake Assembly, 14 Inch Diameter, 800 LB FT, 230 VDC, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist applications. 320 LBS + skid Ships via motor freight. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal
ET-16 Brake Parts Ametek Gemco Electro-Thrust Brake Assembly, 16 Inch Diameter Brake, 1000 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.45 Sec. or With Adjusting Valve 0.8 to 3.8 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist applications. 400 LBS + skid. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal
ET-18NA Brake Parts Ametek Gemco Electro-Thrust Brake Assembly, 18 Inch Diameter Brake, 1500 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.35 Sec. With Adjusting Valve 0.7 to 3.0 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist applications. 640 LBS + skid Ships via motor freight. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures & strip heaters
ET-19 Brake Parts Ametek Gemco Electro-Thrust Brake Assembly, 19 Inch Diameter Brake, 2000 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.35 Sec. or With Adjusting Valve 0.7 to 3.0 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist applications. 6400 LBS + skid. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal
ET-19NA Brake Parts Ametek Gemco Electro-Thrust Brake Assembly, 18 Inch Diameter Brake, 1600 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.35 Sec. With Adjusting Valve 0.7 to 3.0 Sec. to softly apply the brake, 640 LBS + skid Ships via motor freight. Options include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters.
ET-23 Brake Parts Ametek Gemco Electro-Thrust Brake Assembly, 8210-23-4-A-S-X-X-X-I 
23 Inch Diameter Brake, 4000 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.27 Sec. With Adjusting Valve 0.4 to 1.7 Sec. to softly apply the brake, 875 LBS + skid. Options include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters (900LBS)
ET-30 Brake Parts Ametek Gemco Electro-Thrust Brake Assembly, 30 Inch Diameter Brake, 9000 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve TBD Sec. With Adjusting Valve TBD Sec. to softly apply the brake, 1500 LBS + skid
ET-6NA Brake Parts Ametek Gemco Electro-Thrust Brake Assembly, 6 Inch Diameter Brake, 60 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F., Brake Setting Times Without Adjustable Valve 1.1 Sec. / With Adjustable Valve 1.5 to 7.2 Sec., to softly apply the brake, (as such this brake is not suitable for hoist applications ) 120 LBS + skid., Ships via motor freight. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures & strip heaters
ET-8 Brake Parts Ametek Gemco Electro-Thrust Brake Assembly, 8 Inch Diameter Brake, 100 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F., Brake Setting Times Without Adjustable Valve 1.1 Sec. / With Adjustable Valve 1.5 to 7.2 Sec., to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. 140 LBS + skid. Ships via motor freight. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal.
ET-8DC Brake Parts Ametek Gemco Electro-Thrust Brake Assembly, 8 Inch Diameter Brake, 100 LB FT, 230 VDC, Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F., Brake Setting Times Without Adjustable Valve 1.1 Sec. / With Adjustable Valve 1.5 to 7.2 Sec., to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. 140 LBS + skid. Ships via motor freight. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal
ET-8NA Brake Parts Ametek Gemco Electro-Thrust Brake Assembly, 8 Inch Diameter Brake, 160 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 1.1 Sec. With Adjusting Valve 1.5 to 7.2 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. 140 LBS + skid. Options available at additional cost include: Self Adjusting Mechanism for Lining Wear, Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures, strip heaters & hydraulic actuators for auxiliary cab control via a progressive hydraulic brake pedal.
ETH-08NA-DC Brake Only Brake Parts Ametek Gemco Electro-Thrust Brake Assembly, 8 Inch Diameter Brake with hydraulic slave actuator for auxiliary manual cab control via a existing Wagner hydraulic brake system., 160 LB FT, 230 Volt DC Motor, Built to AISE Specifications with the exception of the brake torque which is 60 FT LB higher than AISE specifies, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times; Without Adjusting Valve 1.1 Sec. With Adjusting Valve 1.5 to 7.2 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application (165LBS) Options available at additional cost include: Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures and strip heaters
ETH-10 Brake Only Brake Parts Ametek Gemco spring applied, electro-hydraulically released, 10 inch brake assembly with hydraulic slave actuator for auxiliary manual cab control via the existing Wagner hydraulic brake system. The hydraulic thruster is powered by a 460 / 230 Volt AC motor. 200 FT LBS.
ETH-10 Brake Sys DC Brake Parts Ametek Gemco Electro-Thrust Brake System with Hydraulic Cab Control. 10 Inch Diameter Brake, 200 LB FT, 230 VDC Shunt Wound Motor. Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.3 to 7.3 Sec. to softly apply the brake, hydraulic actuator for auxiliary cab control for a progressive hydraulic brake pedal actuation. System includes: Qty. 1, ET-10 Brake Assembly, Fluid Reservoir Bleeder, Pushbutton Switch with Enclosure for operating the bleeder check valve, Control Cylinder with Foot Pedal, 100 Feet of Hydraulic Tubing, Tube Fittings, Unions, Clamps, Bushings, Brackets, Gaskets, 4 Armored Flexible Hoses & Wagner 21B DOT 3 Super Heavy Duty Brake Fluid SAE1703
ETH-10-DC Brake Only Brake Parts Ametek Gemco Electro-Thrust Brake Assembly, 10 Inch Diameter Brake with hydraulic slave actuator for auxiliary manual cab control via a existing Wagner hydraulic brake system., 200 LB FT, 230 Volt DC Motor, Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times; Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.3 to 7.3 Sec. to softly apply the brake. Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. Options available at additional cost include: Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures and strip heaters # 82300014 (165LBS)
ETH-13 Brake Only Brake Parts Ametek Gemco Electro-Thrust Brake Assembly, 13 Inch Diameter Brake with hydraulic slave actuator for auxiliary manual cab control via a existing Wagner hydraulic brake system., 550 LB FT, 230 / 460 VAC, 3 Phase, 60 Hz., Built to AISE Specifications, Spring Applied Electrohydraulic Release, -13 thru 104 Degrees F. Brake Setting Times, Without Adjusting Valve 0.75 Sec. With Adjusting Valve 1.2 to 4.8 Sec. to softly apply the brake, Engineered for Overhead Crane Trolley & Bridge Applications to reduce swinging loads. NOT designed for hoist application. 250 LBS + skid. Options available at additional cost include: Limit Switches for set and release information, Silicon Fluid for low temperature application -40 degrees F., Hand Release (latching or non-latching) enclosures and strip heaters.
203 Vest Avenue
Valley Park, MO 63088
Toll Free: (888) SPECTECH
Phone: (636) 537-0202
Fax: (636) 537-1405
E:mail: sales@spectechind.com